Table of Contents
Related Manuals for AMI KW950-CR
Summary of Contents for AMI KW950-CR
- Page 1 KW950-CR COURSE RECORDER & GYRO INTERFACE © This Manual and the information contained therein is the property of AMI Marine (UK) It must not be reproduced or otherwise disclosed without prior consent in writing from AMI Marine (UK)
- Page 2 AMI Manual KW 950-CR Doc No: AMI TM950-CR This Page Left Blank Intentionally Manual KW950-CR Iss03 Rev03.doc...
- Page 3 Minor text change Iss03 Rev01 17.12.10 Added Switch Options Table Rev02 18.01.11 Addition of Rudder Angle Rev03 17.03.11 Text change and additional page breaks NOTE: All alterations must be verified by re-authorisation and approval of the complete document. Manual KW950-CR Iss03 Rev03.doc...
- Page 4 AMI Manual KW 950-CR Doc No: AMI TM950-CR This Page Left Blank Intentionally Manual KW950-CR Iss03 Rev03.doc...
-
Page 5: Table Of Contents
AMI Manual KW 950-CR Doc No: AMI TM950-CR KW950-CR Course Recorder & Gyro Interface Course Recorder KW950-CR ................7 Introduction ....................7 Specification ....................8 Installation Guide ....................9 Power Supply SK1 ..................9 Gyro Input - SK2 ..................10 Stepper and Synchro Interface Wiring ............ - Page 6 AMI Manual KW 950-CR Doc No: AMI TM950-CR This Page Is Intentionally Blank Manual KW950-CR Iss03 Rev03.doc...
-
Page 7: Course Recorder Kw950-Cr
The data output from the KW950-CR includes time, date, position, ground speed, course, and the date from GPS, Rudder Angle (if combined with the GPS data prior to the KW950-CR) along with heading from the gyro. Both inputs are combined and passed to the printer with the supplied serial cable. -
Page 8: Specification
Red led 7 segment digits 14mm high, and a 4 segment bar DISPLAY: 9 to 32 volts DC at < 5 watts POWER: DIN case 144 x 72 x 144 deep, with cable glands on rear panel. HOUSING: Manual KW950-CR Iss03 Rev03.doc... -
Page 9: Installation Guide
Installation Guide Location The KW950 can be mounted using the trunnion mount supplied. Alternatively The DIN case will fit a 68 by 132 mm panel cut-out using optional fixing clamps. Wiring Cable entry is via glands on the rear panel. The cable tails should be long enough for the instrument to be withdrawn for service. -
Page 10: Gyro Input - Sk2
Rectified DC Stepper - Negative Steps S1-, and via a diode to Ref- S2-, and via a diode to Ref- S3-, and via a diode to Ref- Common pos to S1+, S2+, S3+, Ref+ ( all linked ) Manual KW950-CR Iss03 Rev03.doc... -
Page 11: Standard Negative Stepper Terminations
5V CMOS (SK 4) PRINTER + 5V Pin 3 = A Pin 7 = 0 DATA IN 2 (SK5) -VE STEPPER 25/70V 6 STEPS PER DEGREE GYRO I/P (SK2) HEADING 24V DC DC INPUT (SK 1) Manual KW950-CR Iss03 Rev03.doc... -
Page 12: 360:1 Synchro
( or Ref+ ) ( try this if first does not follow ) S1-,S2-,S3- ( all linked ) NOTE: If Output rotates in the wrong direction swap S1 and S2 DC Synchro 24Volts S1+ and S3- S2+ and S1- S3+ and S2- Manual KW950-CR Iss03 Rev03.doc... -
Page 13: Standard Synchro 360:1 Terminations
NMEA PORT (SK 3) DATA IN DATA OUT 5V CMOS (SK 4) PRINTER + 5V Pin 3 = A Pin 7 = 0 DATA IN 2 (SK5) SYNCHRO 360:1 GYRO I/P (SK2) HEADING 24V DC DC INPUT (SK 1) Manual KW950-CR Iss03 Rev03.doc... -
Page 14: Data Inputs - Sk3 And Sk5
Note that the power line 0 volts connects to “0”. Before making the connection check that there is no more than 5 volts difference between the KW950-CR output and the lines of the receiving equipment. If a voltage exists damage may be caused to the KW950-CR which will not be covered by our warranty. -
Page 15: Interface Testing
001 011 010 110 100 101. With rectified stepper input LD1 should be on all the time. With a synchro input all leds are on, with each one going off for a short time only at half degree (half rev) intervals. Manual KW950-CR Iss03 Rev03.doc... -
Page 16: Printer Settings
8bit Parallel I/F bi-directional mode Packet mode Auto Character table PC 437 International character set for Italic table Italic U.S.A. Manual feed wait time 1.5 seconds Buzzer Auto CR (IBM 2380 Plus) IBM character table Table2 Manual KW950-CR Iss03 Rev03.doc... -
Page 17: Board Layout
AMI Manual KW 950-CR Doc No: AMI TM950-CR Board Layout Manual KW950-CR Iss03 Rev03.doc... - Page 18 AMI Manual KW 950-CR Doc No: AMI TM950-CR This Page Is Intentionally Blank Manual KW950-CR Iss03 Rev03.doc...
-
Page 19: Warranty Registration Form
Eastleigh Hants SO50 6NZ A full explanation of AMI Marine (UK) Ltd warranty conditions can be found on our web site or requested via email. * Terms of Service and Policies are subject to change without notice. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Please complete and return to AMI Marine (UK) either by post to the above address or by email to technical@amimarine.net... - Page 20 AMI Manual KW 950-CR Doc No: AMI TM950-CR This Page Is Intentionally Blank Manual KW950-CR Iss03 Rev03.doc...
Need help?
Do you have a question about the KW950-CR and is the answer not in the manual?
Questions and answers