Kingfisher FPCSP46-2 Manual

Kingfisher FPCSP46-2 Manual

Petrol chain saw (45.8 cm3)

Advertisement

Quick Links

Petrol Chain Saw
(45.8 cm
)
3
FPCSP46-2
EAN: 5059340141343
BX220IM
WARNING: Read the instructions before using the product!

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FPCSP46-2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Kingfisher FPCSP46-2

  • Page 1 Petrol Chain Saw (45.8 cm FPCSP46-2 EAN: 5059340141343 BX220IM WARNING: Read the instructions before using the product!
  • Page 2: Table Of Contents

    FPCSP46-2 Let’s get started... These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. Getting Started... Safety information Your product Before start Quick start more detail... Product functions Operation Care maintenance...
  • Page 3: Safety Warnings

    Safety information FPCSP46-2 Safety warnings 1. This product is not intended for use by children and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge. 2. Children should be supervised to ensure that they do not play with the product.
  • Page 4 Safety information FPCSP46-2 15. Do not under any circumstances modify the product. Modifications can result in serious personal injury or death. 16. Do not start cutting until you have a clear work area and secure footing. 17. All product servicing and maintenance, other than the items listed in this manual, should be performed by an authorised service centre.
  • Page 5: Getting Started

    Safety information FPCSP46-2 9. Use caution when handling fuel. To avoid any accidental fires, move the product at least 3 metres from the fuelling point before starting the engine. 10. Tighten the fuel tank cap thoroughly after refilling the fuel tank.
  • Page 6 Safety information FPCSP46-2 Operation 1. When sawing ensure the product does not touch any foreign materials such as rocks, fences, nails etc. Such objects may be flung out and could result in damage to the product, serious or even fatal injuries.
  • Page 7: Safety Information

    Safety information FPCSP46-2 Transport and storage 1. Stop the engine and engage the chain brake before transporting the product. 2. Carry the product with the engine stopped, the guide bar and saw chain to the rear, and the exhaust away from the body.
  • Page 8 Safety information FPCSP46-2 3. Only use replacement bars and chains specified by the manufacturer. Incorrect replacement bars and chains may cause chain breakage and/or kickback. 4. Follow the manufacturer’s sharpening and maintenance instructions for the saw chain. Decreasing the depth gauge height can lead to increased kickback.
  • Page 9 Safety information FPCSP46-2 Residual risks Even if you are operating this product in accordance with all the safety requirements, potential risks of injury and damage remain. The following dangers can arise in connection with the structure and design of this product: 1.
  • Page 10 Safety information FPCSP46-2 Description of signal words: The signal word that indicates a hazard with a high level of risk DANGER! which, if not avoided, will result in death or serious injury. The signal word that indicates a hazard with a medium level of WARNING! risk which, if not avoided, could result in death or serious injury.
  • Page 11 Safety information FPCSP46-2 Petrol engines produce toxic carbon monoxide exhaust fumes. Breathing carbon monoxide can cause nausea, fainting or even death. Do not operate the engine indoors! Always hold the product firmly in both hands. Kickback! Tip contact may cause the guide bar to move suddenly upward and backwards what may cause serious injury to user.
  • Page 12 Safety information FPCSP46-2 Choke – CLOSE position. Choke – OPEN position. Stop switch positions. Stop the engine. Press the primer 8 times before starting the cold engine. Objects thrown by the product could hit the operator or other bystanders. Always ensure that other people and pets remain at a safe distance from the product when it is in operation.
  • Page 13: Your Product

    Your product FPCSP46-2 20 21 1. Lubrication holes (on both sides) 12. Stop switch 2. Guide bar 13. Fuel tank cap 3. Saw chain 14. Adjusting screws for carburetor 4. Front hand guard (with chain brake) 15. Recoil starter handle 5.
  • Page 14: Technical Specifications

    Your product FPCSP46-2 Content of delivery 22. Chain oil flow adjuster 25. Screwdriver 23. Main unit 26. Fuel mixing container 24. Multi-tool 27. Guide bar cover Technical specifications General > Dimensions: approx. 48 x 26 x 30 mm Machine without guide bar, saw chain and >...
  • Page 15 Your product FPCSP46-2 Engine > Engine model: 1E43F-2 > Engine type: air cooled, 2-stroke engine > Engine displacement: 45.8 cm > Nominal power: 1.6 kW > Maximum operating engine speed (rotational frequency): 12000 min Idle speed: > 3000 min >...
  • Page 16: Before You Start

    Before you start FPCSP46-2 Unpacking 1. Unpack all parts and lay them on a flat, stable surface. 2. Remove all packing materials and protective shipping materials, if applicable. 3. Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the product and contact your dealer.
  • Page 17 Before you start FPCSP46-2 Assembly WARNING! The product must be fully assembled before operation! Do not use a product that is only partly assembled or assembled with damaged parts! Follow the assembly instructions step-by-step and use the pictures provided as a visual guide to assemble the product easily! Disconnect the spark plug connector before assembly! Reconnect it after assembly (see "Maintenance").
  • Page 18 Before you start FPCSP46-2 1. Pull the front hand guard (4) backwards to disengage the chain brake (Fig. 1). 2. Unscrew the fixing nuts (18) using the multi-tool (24) and remove them together with the clutch cover (17) (Fig. 2).
  • Page 19 Before you start FPCSP46-2 3. Place the slot on the guide bar (2) over the 2 bolts. Make sure to fit the guide bar with the saw chain “cutter” symbol at the top of the bar (step 1, Fig. 3).
  • Page 20 Before you start FPCSP46-2 7. Refit the clutch cover (17) and fasten using the fixing nuts (18) and the multi-tool (24). To fit the clutch cover, align the tensioner pin with the lower hole on the guide bar by turning the chain tension adjuster (19) clockwise or anti-clockwise with the multi- tool (Fig.
  • Page 21 Before you start FPCSP46-2 WARNING! Disconnect the spark plug connector before adjusting saw chain tension! The cutting edges of the saw chain are sharp! Always wear protective gloves when handling chain! Always maintain proper chain tension! A loose chain increases the risk of...
  • Page 22: Chain Lubrication

    Before you start FPCSP46-2 Switching between standard/winter operation Set the vent for the carburettor to standard or winter operation mode. In winter operation mode the vent is open so that the hot air from around the cylinder can flow to the carburettor.
  • Page 23 Before you start FPCSP46-2 5 mm 4. Wipe up spilled saw chain oil with a soft cloth. Refit and screw the oil tank cap firmly (Fig. 11). NOTE: Always dispose of used saw chain oil and objects contaminated with them in accordance with local regulations.
  • Page 24 Before you start FPCSP46-2 Filling up fuel and oil WARNING! This product is not supplied with petrol-oil mixture in the engine! Before operating this product it is essential to fill it with petrol-oil mixture! This product is equipped with a 2-stroke engine, the fuel and oil tank are combined and it is essential to fill a fuel-oil mixture before operating this product.
  • Page 25 Before you start FPCSP46-2 100 ml 2.5 ml 200 ml 5 ml 40:1 300 ml 7.5 ml 400 ml 10 ml 4. Unscrew and remove the fuel tank cap (13) (Fig. 15). 5. Fill the fuel into the fuel tank. Leave approximately 5 mm of space between the top of the fuel and the inside edge of the tank to allow for expansion.
  • Page 26: Operating Controls

    Before you start FPCSP46-2 Operating controls Front hand guard Choke knob Primer Throttle trigger lock-out Oil tank cap Recoil starter handle Stop switch Fuel tank cap Throttle trigger Chain oil flow adjuster...
  • Page 27: Quick Start

    Quick start FPCSP46-2 Preparation Add fuel and oil Assemble Adjust Add chain oil mixture Starting Engage the Set stop switch Press primer Fully pull Pull recoil chain brake to I 8 times choke knob starter handle 4 times Full press in...
  • Page 28: Intended Use

    For safe use it is essential to read the entire instruction manual before first use! Intended use This petrol chain saw FPCSP46-2 is designated with a power output of 1.6 kW. The product is intended for cutting logs and limbs with a thickness of max. 37.5 cm (see “Technical specifications”).
  • Page 29: Safety Equipment

    Quick start / Product functions FPCSP46-2 This product must not be used for cutting other materials, such as plastic, stone, metal, wood that contains foreign objects, or materials that are harmful to health. This product should not be used outside of domestic premises e.g. for cutting firewood in forested areas.
  • Page 30: Product Functions

    Product functions FPCSP46-2 Chain brake / front hand guard The front hand guard (4) is a safety mechanism that stops the saw chain (3) immediately when it is pushed towards the operator in case of a kickback. The chain brake is a safety mechanism activated by the front hand guard (4). When kickback occurs, the saw chain stops immediately.
  • Page 31 Product functions FPCSP46-2 Chain brake test – non-manual chain brake The non-manual chain brake stops the operation of the saw chain in such a manner that the kickback action produced at the end of the guide bar non-manually engages the chain brake.
  • Page 32: Operation

    Operation FPCSP46-2 Operation Check before starting: 1. Check the product, as well as accessories for damage before each use. Do not use the product if it is damaged or shows wear. 2. Double check that accessories and the guide bar/saw chain are properly fixed.
  • Page 33 Operation FPCSP46-2 Engine cold start 1. Place the saw where it does not come into contact with any objects. 2. Engage the chain brake. 3. Set stop switch (12) to I (Fig. 21). 4. Press the primer (8) until the bubble is filled with fuel (6-8 times) (Fig. 22).
  • Page 34 Operation FPCSP46-2 Engine warm start 1. Place the saw where it does not come into contact with any objects. 2. Engage the chain brake. 3. Set stop switch (12) to I (Fig. 25). 4. Pull out the choke knob (7) fully and then press in back in fully (Fig. 26).
  • Page 35 Operation FPCSP46-2 Basic operating / cutting procedure 1. To become proficient attend a recognised chain saw training course to learn how to operate chain saws safely and effectively. Familiarise yourself with all the controls and switches. Practise all movements with the product switched off.
  • Page 36 Operation FPCSP46-2 8. Do not operate the product with arms fully extended or attempt to saw areas which are difficult to reach, or on a ladder. Never use the product above shoulder height (Fig. 29). 9. Optimum sawing is achieved if the chain speed remains constant during cutting.
  • Page 37 Operation FPCSP46-2 1. Pinching the saw chain (3) along the bottom of the guide bar (2) may pull the product forward away from the operator (“skating”) (Fig. 31). 2. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back toward the operator (“bouncing”) (Fig.
  • Page 38: Felling A Tree

    Operation FPCSP46-2 WARNING! Most “kickback” accidents happen during limbing! Pay close attention to the position of the ‘kickback’ zone of the bar when you are “limbing branches that are under tension. Felling a tree 1. When bucking and felling operations are being performed by two or more persons at the same time, the felling operations should be separated from the bucking operation by a distance of at least twice the height of the tree being felled.
  • Page 39: Limbing And Pruning

    Operation FPCSP46-2 Felling back cut 1. Make the felling back cut (Fig. 34, A) at least 50 mm higher than the horizontal notching cut (Fig. 34). Keep the felling back cut parallel to the horizontal notching cut. Make the felling back cut so enough wood is left to act as a hinge. The hinge (Fig.
  • Page 40: Bucking A Log

    Operation FPCSP46-2 Cutting spring poles A spring pole is any log, branch, rooted stump, or sapling which is bent under tension by other wood so that it springs back if the wood holding it is cut or removed. On a fallen tree, a rooted stump has a high potential of springing back to the upright position during the bucking cut to separate the log from the stump.
  • Page 41: After Use

    Operation FPCSP46-2 5. Support small logs on a sawing stand or another log while bucking (Fig. 40). 6. If the wood diameter is large enough for you to insert a soft bucking wedge without touching the chain, you should use the wedge to hold the cut open to prevent pinching (Fig.
  • Page 42: Care And Maintenance

    Care and maintenance FPCSP46-2 The golden rules for care WARNING! Always stop the engine, disconnect the spark plug connector and let the product cool before performing inspection, maintenance and cleaning work. DANGER! Proper maintenance is essential for safe and trouble free operation.
  • Page 43: Maintenance Table

    Care and maintenance FPCSP46-2 Cleaning the guide bar > Disassemble the guide bar (2) and saw chain in reversed order from assembly. > Remove any dirt accumulated inside the guide bar slot using the putty knife (not provided) (Fig. 42).
  • Page 44 Care and maintenance FPCSP46-2 Sprocket wheel 1. Clean the sprocket wheel. 2. Using a disposable lube gun, insert the needle nose into the lubrication hole (1) and inject grease until it appears at the outside edge of the sprocket (Fig. 43).
  • Page 45 Care and maintenance FPCSP46-2 4. Remove any dirt accumulated inside the guide bar slot using the putty knife (not provided) (Fig. 45). 5. Check the guide bar “rail” for wear: Hold a ruler (straight edge) against the side of the guide bar and “cutter side plates”. If there is a gap between the ruler and guide bar the guide bar “rail”...
  • Page 46 Care and maintenance FPCSP46-2 2. The height difference between the tooth and the ridge is the cutting depth. When sharpening the saw chain (3) you have to consider the following points (Fig. 47). > File angle > Cutting angle >...
  • Page 47: Air Filter

    Care and maintenance FPCSP46-2 9. Use a depth gauge measuring instrument File position Cutting tip to check the height of Depth gauge the depth gauge. Depth Cutting length setting 1.27 mm Top plate gauge measuring jigs (0.05") are available from most reputable tool merchants (Fig.
  • Page 48: Fuel Filter

    Care and maintenance FPCSP46-2 Fuel filter The fuel tank of this product is fitted with a filter located at the free end of the fuel pipe. The fuel tank of this product is fitted with a filter located at the free end of the fuel pipe.
  • Page 49: Adjusting The Carburetor

    Care and maintenance FPCSP46-2 4. Check the spark plug for damage and wear. The colour of the electrode should be light-brown. 5. Remove the deposits from the electrode with a soft wired brush. Avoid heavy cleaning of the electrode. 6. Dry the spark plug with a soft cloth, if it is wet from fuel.
  • Page 50: Spare Parts/Replacement Parts

    Care and maintenance FPCSP46-2 Spare parts/Replacement parts The following parts of this product may be replaced by the consumer. Spare parts are available at an authorised dealer or through our customer service. Description Model no. or Specification Guide bar (2)
  • Page 51 Care and maintenance FPCSP46-2 Long term storage NOTE: Risk of product damage! > If you are not going to be using the product for a while, remove the fuel and saw chain oil from the product. This way, you will prevent a gumming-up of the engine and of the grease pump.
  • Page 52: Troubleshooting

    Troubleshooting FPCSP46-2 Troubleshooting Suspected malfunctions are often due to causes that the operators can fix themselves. Therefore check the product using this section. In most cases, the problem can be solved quickly. WARNING! Only perform the steps described in these instructions! All further...
  • Page 53 Troubleshooting FPCSP46-2 Problem Possible cause Solution Engine does Spark plug defective? Replace spark plug. not start. Engine cold? Follow cold starting procedure. Carburetor setting not correct? Adjust the carburetor. Engine does Air filter is soiled? Clean the air filter. not reach Spark plug is soiled (tip is Clean spark plug.
  • Page 54: Recycling And Disposal

    Recycling and disposal / Guarantee FPCSP46-2 Recycling and disposal 1. Old products are potentially recyclable and do not, therefore, belong in your household rubbish. You are requested to assist us and our contribution to saving resources and protecting the environment by handing in this product to an equipped collection centre (if there is one available).
  • Page 55: Ec Declaration Of Conformity

    Nazwa i adres producenta lub jego upoważnionego przedstawiciela: Denumirea și adresa producătorului sau a reprezentantului său autorizat: Nombre y dirección del fabricante o de su representante autorizado: Nome e endereço do fabricante ou do respetivo mandatário: Kingfisher International Products B.V., Rapenburgerstraat 175E, 1011 VM Amsterdam, The Netherlands www.kingfisher.com/products...
  • Page 56 EC declaration of conformity FPCSP46-2 The object of the declaration described above is in conformity with the relevant Union harmonisation legislation: L’objet de la déclaration décrit ci-dessus est conforme à la législation d’harmonisation de l’Union applicable: Wymieniony powyżej przedmiot niniejszej deklaracji jest zgodny z odnośnymi wymaganiami unijnego prawodawstwa harmonizacyjnego: Obiectul declarației descris mai sus este în conformitate cu legislația relevantă...
  • Page 57 Semnatar autorizat şi deţinătorul dosarului ethnic/Firmante autorizado y titular del expediente técnico/Signatário David Awe autorizado e detentor da ficha técnica: Group Quality & Sustainability Director On/le/dnia/la/am/el/em: 11/08/2020 Kingfisher International Products B.V., Rapenburgerstraat 175E, 1011 VM Amsterdam, The Netherlands www.kingfisher.com/products...
  • Page 58 Manufacturer, Fabricant, Prodecent, Producător, Fabricante: UK Manufacturer: Kingfisher International Products Limited 3 Sheldon Square London W2 6PX United Kingdom EU Manufacturer: Kingfisher International Products B.V. Rapenburgerstraat 175E 1011 VM Amsterdam The Netherlands www.diy.com www.screwfix.com www.screwfix.ie To view instruction manuals online,...

This manual is also suitable for:

5059340141343

Table of Contents

Save PDF