Advertisement
SERVICE MANUAL
EN
DESCRIPTION
These Pressure Tanks are CE marked in accordance
with Pressure Equipment Directive 2014/68/EU and
ATEX Directive 2014/34/EU Protection level II 2 G
X T4/Ex h IIB T4 Gb for use in Zones 1 and 2.
The agitators are marked in accordance with ATEX
Directive 2014/34/EU Protection level II 1/2 G Ex h
IIB T4 Ga/Gb, and to Machinery Safety Directive
2006/42/EC.
These pressure tanks are designed as a pressure
container to supply liquid material at a constant
preset pressure up to a maximum of 7.6 bar
(110 psi). The tanks are built to ASME BPV XIII
standards.
183G models are constructed from Galvanised
carbon steel. 183S models are constructed from
stainless steel, and are better suitable for use with
water based and more corrosive materials. They
are suitable for use with flammable materials.
A polyethylene liner is included for easy clean up.
Important: Read and follow all instructions and SAFETY PRECAUTIONS before using
77-3135-R9 (6/2024)
PRESSURE FEED TANK ASSEMBLIES
9.5, 40, AND 60 LITER CAPACITIES
9.5 Liter
TANK MODEL
183S-210-CE
183S-211-CE
183S-212-CE
183S-213-CE
183G-1010-CE
183G-1012-CE
183G-1013-CE
183S-1010-CE
183S-1012-CE
183S-1013-CE
183S-1510-CE
183S-1512-CE
183S-1513-CE
this equipment. Retain for future reference.
40 Liter
CAPACITY
9.5 L [2 Gallon]
9.5 L [2 Gallon]
9.5 L [2 Gallon]
9.5 L [2 Gallon]
40 L [10 Gallon]
40 L [10 Gallon]
40 L [10 Gallon]
40 L [10 Gallon]
40 L [10 Gallon]
40 L [10 Gallon]
60 L [15 Gallon]
60 L [15 Gallon]
60 L [15 Gallon]
1 / 16
60 Liter
TANK MATERIAL
AGITATION
Stainless Steel
none
Stainless Steel
Direct Drive
Stainless Steel
Manual
Stainless Steel
Gear Reduced
Galvanized Steel
none
Galvanized Steel
Manual
Galvanized Steel
Gear Reduced
Stainless Steel
none
Stainless Steel
Manual
Stainless Steel
Gear Reduced
Stainless Steel
none
Stainless Steel
Manual
Stainless Steel
Gear Reduced
77-xxxx-R1.0
Page #
www.carlisleft.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Carlisle BINKS 183S-210-CE
Summary of Contents for Carlisle BINKS 183S-210-CE
- Page 1 SERVICE MANUAL PRESSURE FEED TANK ASSEMBLIES 9.5, 40, AND 60 LITER CAPACITIES 9.5 Liter 40 Liter 60 Liter DESCRIPTION TANK MODEL CAPACITY TANK MATERIAL AGITATION 183S-210-CE 9.5 L [2 Gallon] Stainless Steel none These Pressure Tanks are CE marked in accordance 183S-211-CE 9.5 L [2 Gallon] Stainless Steel...
- Page 2 In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: WARNING NOTE CAUTION Hazards or unsafe practices which Hazards or unsafe practices which could result in severe personal Important installation, operation or could result in minor personal injury, injury, death or substantial property maintenance information.
-
Page 3: Pressure Relief Procedure
SAFEGUARDS The following hazards may occur during the normal use of this equipment. Please read the following chart. HAZARD CAUSE SAFEGUARDS Fire Solvents and coatings can be highly 1. Adequate exhaust must be provided to keep the air free flammable or combustible, especially of accumulations of flammable vapors. -
Page 4: Specifications And Options
SPECIFICATIONS & OPTIONS SPECIFICATIONS GALVANIZED TANKS STAINLESS STEEL TANKS Maximum Working Pressure 7.5 bar [110 PSI] 7.5 bar [110 PSI] Tank Shell SA-414 Steel, Galvanized (Zinc) 304 Stainless Steel Tank Lid SA-414 Steel, Galvanized (Zinc) 304 Stainless Steel Fluid Tube 3/8 in. -
Page 5: Maintenance
OPERATION & SERVICE CHECKS OPERATION 7. Cup cloth over air cap on the gun and pull WARNING trigger. This will force material back 1. Close the air inlet valve to tank. Turn through the hose into the tank. High pressure can cause serious injury. handle on regulator counterclockwise until 8. - Page 6 9.5 LITER STAINLESS STEEL TANK ASSEMBLIES NOTE ITEM Use PTFE based thread sealant on PART NO. DESCRIPTION QTY. all air and fluid connections. QN-97 HANDLE ▲ PETROLEUM QMS-2 PLUG (NON-AGITATED MODELS ONLY) JELLY/GREASE SSG-8184-K2 O-RING (KIT OF 2) ▲ ■ QMG-21 AIR MANIFOLD SS-2707...
- Page 7 9.5 LITER TANK – DIRECT DRIVE AGITATOR DIRECT DRIVE AG Note Use PTFE based thread sealant on all air and fluid connections STAN PETROLEUM JELLY/GREASE Note Open side of shaft seal (31) faces downward. Retainer (32) required only for vacuum operation.
- Page 8 9.5 LITER TANK – GEAR-REDUCED AGITATOR GEAR-REDUCED AGITATOR Note Use PTFE based thread sealant on all air and fluid connections GEAR-REDUCED AGITATOR-REGULAT HOOK-UP Refer to 77-3141 for 31-452-CE details. STANDARD REGULATION 1 OR 2 REGULATORS ...
- Page 9 5/10/15-GALLON GALVANIZED TANK ASSEMBLIES 40 & 60 LITER TANK ASSEMBLIES NOTE NOTE Refer to 77-3141 for Open side of the shaft seal (8) Use PTFE based thread sealant more information (39). faces downward. on all air and fluid connections. Retainer (9) required only for vacuum operation.
- Page 10 40 & 60 LITER STAINLESS STEEL TANK ASSEMBLIES – PARTS LIST STAINLESS STEEL GALVANIZED 40 L 60 L 40 L ITEM PART NO. DESCRIPTION QTY. QTY. QTY. QMS-46 RETAINING NUT ▲ QMG-85 THRUST WASHER ▲ ----- THRUST COLLAR ▲ ----- SET SCREW (5/16-18 X 3/8) ▲•...
- Page 11 TANKS – AIR CONTROL SINGLE REGULATOR AIR CONTROL Control tank pressure only. 85-470 for non-agitated tanks 85-471 for agitated tanks *Items with an asterisk are for use with an agitator. ITEM PART DESCRIPTION 85-470 85-471 HAR-511 AIR REGULATOR 20-1753-1 BUSHING-STL-PLTD – 3/8 (m) x 1/4 (f) VA-542 BALL VALVE 83-1290...
- Page 12 85-469 CONVERSION TO DOUBLE REGULATOR ASSEMBLY KIT Convert standard single regulator or extra-sensitive air control to a double regulator air control. ITEM PART DESCRIPTION QTY. • — 1/4 NPT PLUG (SUPPLIED W/ REGULATOR) 83-4233 D.M. NIPPLE 1/4 x 3/8 HAR-507 AIR REGULATOR 83-1355 GAUGE –...
- Page 13 NOTES 77-3135-R9 (6/2024) 13 / 16 www.carlisleft.com...
- Page 14 NOTES www.carlisleft.com 14 / 16 77-3135-R9 (6/2024)
- Page 15 IN ACCORDANCE WITH PED 2014/68/EC Carlisle Fluid Technology confirms that the products listed below, defined under the Pressure Equipment Directive (PED) 2014/68/EC as ‘Pressure Accessories’ , are below or equal to the limits set out in points (a), (b) and (c) of paragraph 1 and in paragraph 2 respectively and have been designed and manufactured in accordance with Sound Engineering Practice (SEP) Article 4, Paragraph 3.
-
Page 16: Warranty Policy
This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty. The use of any parts or accessories, from a source other than Carlisle Fluid Technologies, will void all warranties. Failure to reasonably follow any maintenance guidance provided may invalidate any warranty.
Need help?
Do you have a question about the BINKS 183S-210-CE and is the answer not in the manual?
Questions and answers