Advertisement
Quick Links
1
Product Overview
Introduction
1.1
The SD6 is a highly integrated Bluetooth 5.0 low energy module device. It has 32-bit ARM® Cortex™-M0 CPU
with 512KB Flash, 64KB SRAM and an ultra-low power, high performance, multi-mode radio. It intergrates rich
feature peripheral units, programmable protocol and profile to support BLE application, makes customers'
product to be built with minimum bill-of-material (BOM) cost.
Features
1.2
Features
1.3
CPU
⚫ 32-bit ARM® Cortex™-M0 CPU
⚫ Up to 64MHz clock
Memories
⚫ 512KB Flash
⚫ 64KB Data SRAM
⚫ 8KB Code Cache
2.4GHz Transceiver
⚫ Compliant to Bluetooth 5.0
⚫ Single-pin antenna: no RF matching or
RX/TX switching required
⚫ Support two data rates
— 2Mbps
— 1Mbps
⚫ TX Power -20 to +5dBm in 3dB steps
Low power consumption
⚫ Transmitter: 5.5mA@0dBm Tx power, with
DC-DC
⚫ Receiver: 5mA @with DC-DC
⚫ Sleep Mode 13μA@with 32KHz RTC and all
SRAM retention
⚫ 0.7μA @ OFF Mode(IO wake up only)
Oscillator
⚫ Support 16M XTAL
⚫ Embedded 32M RC oscillator and 32K RC
oscillator
PeriPheral
⚫ 20/9 general purpose I/O pins
— All pins can be configured as digital interface
by
programmable
mapping(except P01)
— All pins can be configured for wake-up and
IO
MUX
function
Advertisement
Related Manuals for EDAN SD6
Summary of Contents for EDAN SD6
- Page 1 Product Overview Introduction The SD6 is a highly integrated Bluetooth 5.0 low energy module device. It has 32-bit ARM® Cortex™-M0 CPU with 512KB Flash, 64KB SRAM and an ultra-low power, high performance, multi-mode radio. It intergrates rich feature peripheral units, programmable protocol and profile to support BLE application, makes customers’...
-
Page 2: Flexible Power Management
⚫ Embedded 1.35V buck DC-DC converter(it external interrupt does not exist in SOP16 package) — All pins output state can be retained Package in sleep mode ⚫ 2x UART ⚫ QFN32（4*4*0.75mm） ⚫ 6-channel output PWM ⚫ SOP16（9.90*3.90*1.40mm） ⚫ 2x I2C Certification ⚫... - Page 3 This section describes the pin assignment and the pin functions for the different package types. CST92F34-SOP16 Figure 1.1 Module pin assignments Table 1.1 Pin description item Pin name Type Description Ground BAT_IN 3.3V power input Reserved Reserved Reserved Reserved P14/WAKEUP General purpose input/output P02/SWD_IO General purpose input/output / SWD debug IO...
- Page 4 FCC Statement This Module complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this module may not cause harmful interference, and (2) this module must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- Page 5 Limited module procedures This module will only use in Edan Instruments, Inc’s host device only. We will retain control over the final installation of the modular such that compliance of the end product is assured.
- Page 6 Information on test modes and additional testing requirements When install this modular with limit modular approval, Edan Instruments, Inc will perform the test of radiated emission and spurious emission according to FCC part 15C:15.247 and 15.209 requirement, only if the test result comply with FCC part 15.247 and 15.209 requirement, then the host can be sold legally.
Need help?
Do you have a question about the SD6 and is the answer not in the manual?
Questions and answers