Advertisement
GENERAL CONTROLS
Volume knob and
function selector
Disc controls
Selecting the source to play
Slide the FUNCTION selector to select CD, TUNER
CD:
or AUDIO IN.
To play back a disc. (See "DISC OPERATIONS. " )
TUNER:
To listen to the radio broadcast. (See "TUNER
OPERATIONS. " )
AUDIO IN:
To listen to the other equipment connected to
the AUDIO IN jack. (See "LISTENING TO OTHER
EQUIPMENT. " )
DISC OPERATIONS
Basic procedure
1
4
Load a disc.
Adjust the volume.
2
Set the source to CD.
To stop playback
The total number of
tracks
3
Start playback.
To pause playback
The current track
number
• To resume, press the same button again.
Disc holder
Radio controls
Display
Adjusting the volume
Turning the unit off
Turn the VOLUME knob to increase or decrease the
Slide the FUNCTION selector to
volume.
• Set the volume to minimum when you turn on the
unit.
Decrease
Increase
Program playback
Up to 20 tracks can be programmed to play in a
desired order.
To program the playing order
While playback is stopped...
1
Show the program creation display.
Program number
• Now you can select the first track of the
program.
To select a track
2
Select a desired track.
To locate a desired position on the disc
During playback...
3
Add the track to the program.
• The next program number appears on the
Press and hold
display, then track selection display is shown.
Program number
TUNER OPERATIONS
Basic procedure
1
3
Set the source to TUNER.
Select a station.
2
Select the band—FM or AM.
OFF.
4
Adjust the volume.
Repeat/Random playback
4
Select the desired playback mode.
Repeat steps 2 and 3.
• When the 20th track is programmed, "- - -"
flashes on the display and the 21st track
cannot be programmed.
5
Start playback.
Each time you press the button, the playback
mode changes as follows:
Indicator
• After program playback ended or stopped, the
REPEAT
program playback mode is automatically canceled.
REPEAT ALL
(The PROGRAM indicator disappears from the
display.)
RANDOM
To play back the program again, press PROGRAM,
To cancel, press the same button repeatedly until
then PLAY/PAUSE 6.
the indicator above disappears from the display.
• Repeat playback is also canceled if the playback
To edit the program
is stopped.
1 While playback is stopped, press PROGRAM
• Random playback cannot be used during
repeatedly to select the program number of the
program playback. If you program the playing
track you want to replace.
order during random playback, random
• To add a track at the end of the program, select
playback is canceled.
the last program number.
2 Perform steps 2 and 3 on the left column to select
a new track.
To erase the entire program
While playback is stopped...
1 Press PROGRAM.
• PROGRAM indicator lights up on the display.
2 Press 7.
• The entire program is also erased in the following
cases:
– when you open the disc holder.
– when the unit is turned off.
– when you select another source.
Improving the FM reception
When an FM stereo (FM ST) broadcast is hard to receive or noisy, select the monaural reception
(MONO).
• To restore stereo reception, switch to FM ST.
Adjusting the antenna
FM
Moves to indicate the
current frequency
LISTENING TO OTHER
EQUIPMENT
Playback mode indicator (See below.)
Playback mode
Repeats the current track.
Repeats all tracks.
Plays tracks at random.
Basic procedure
1
Turn the volume to minimum.
2
Connect the equipment.
• Connect the equipment with the stereo
mini plug (3.5 mm (3/16 in) diameter) to
the AUDIO IN jack on the rear.
AM
The AM antenna is built in, so adjusting the
position of the unit may help AM reception.
3
Set the source to AUDIO IN.
4
Start playing the equipment.
5
Adjust the volume.
Advertisement
