Related Manuals for Nexigo ALR-F100
Summary of Contents for Nexigo ALR-F100
- Page 1 100" Fresnel Ambient Light Rejecting Screen for UST Projectors ALR-F100 User Manual Scan the QR code or visit our link to download the latest manual or watch the installation video. nexigo.com/manuals...
-
Page 2: Contact Information
14 days of the delivery date, and we will extend your warranty coverage another year, for a total of two years! From all of us here at NexiGo, we want to thank you for your trust in us. We look forward to serving you again in the near future. -
Page 3: Parts List
Thank you for choosing NexiGo! After unpacking your unit, please check the packaging to make sure that every piece on the Parts List is present. PARTS LIST Code Name Image Quantity Code Name Image Quantity Horizontal Horizontal Inner Frame Inner Frame... -
Page 4: Spare Parts
Stretcher Nut Stretcher Bolt INSTALLATION INSTRUCTIONS This installation video contains detailed instructions on the operation and installation of the NexiGo Ambient Light Rejecting Screen. Please scan the QR code below and FOLLOW THE INSTALLATION VIDEO to install and use. -03-... -
Page 5: Installation Steps
INSTALLATION STEPS Please wear gloves to protect the screen from fingerprints. Gloves ASSEMBLING THE INNER FRAME Step 1: Before you begin, unfold the white Installation Mat (l) and lay it on a clean floor. Perform all installation steps on top of the Installation Mat to avoid damaging the screen. - Page 6 Step 3: Remove the Auxiliary Screw (E) stored in the Horizontal Brackets (C). Step 4: Insert each Horizontal Bracket (C) into its neighboring Horizontal Inner Frame (A1/A2) segment and fasten one side first, then slide to the other side and fix it with the 4 mm Allen Wrench (Z2).
- Page 7 Step 5: Remove the Auxiliary Screw (E) stored in the Corner Brackets (D). Step 6: Insert each Corner Bracket (D) into its neighboring Horizontal Inner Frame (A2, A1) and Vertical Inner Frame (B). -06-...
- Page 8 Step 7: Reinsert and fasten the Auxiliary Screw (E) using the 4 mm Allen Wrench (Z2) to connect each side of the Inner Frame (A1/A2). Repeat this step for all four Corner Brackets (D). Step 8: Finally, attach the Support Beam (F) to the Inner Frame (A1/A2).
- Page 9 Step 10: Set the Inner Frame aside for later. INSTALLING THE FRESNEL SCREEN Step 1: Remove the protective brackets at each end of the cardboard tube to unpack the Fresnel Screen. To remove the brackets, use the 4 mm Allen Wrench (Z2) to remove the screws holding the brackets together.
- Page 10 Step 2: Carefully remove the Fresnel Screen (H) from the tube and unroll it onto the Installation Mat with the rear side facing upward. The rear side of the screen is labeled THIS WAY UP so that you know which half of the screen should be nearest to the floor when you install the Fresnel Screen.
- Page 11 Step 4: Align the Inner Frame with the rear side of the Fresnel Screen (H). Handle with care to avoid creasing the screen. Step 5: Insert the Fiberglass Rods (J1, J2) into the black sleeves along the edges of the screen as shown below.
- Page 12 Step 6: Slide the Stretcher Bars (M, N) over the Fiberglass Rods (J1, J2) at the edges of the screen, as shown in the figure below. Please take out Connecting Rod (X) before installing the Stretcher Bars (M). Step 7: Slide the Stretcher Nuts (K) on the...
- Page 13 Step 8: Insert a Stretcher Bolt (L) into each Stretcher Nut (K) and fasten them using the 3 mm Allen Wrench (Z3). For now, only tighten the Stretcher Bolts halfway. They should be installed in the sequence of 1-1→2-2 →3-3→4-4, as shown in the figure below. Step 9: Before you continue, ensure that the screen is laying properly without any creasing or distortion.
- Page 14 (P) to connect the segments of the Horizontal Outer Frame (Q1, Q2, Q3) as shown below. Horizontal Outer Frame (Q3) is the frame piece with the NexiGo logo. Connect the Horizontal Outer Frame (Q1, Q3) and place it on the side of your Fresnel Screen...
- Page 15 Step 2: Connect the Vertical Outer Frame (R) to the Horizontal Outer Frame (Q1, Q2, Q3) using the Corner Protectors (O). Step 3: Fix the Outer Frame to the Inner Frame using the Screws (G). -14-...
- Page 16 Step 4: Remove the adhesive film from the back of the Wall Protectors (U) and attach them onto the lower Horizontal Inner Frame (A1, A2). Ensure that the Wall Protectors (U) are placed at the bottom of the screen. Each Wall Protector should be placed roughly 12 in (310mm) from the outer corners.
- Page 17 MOUNTING THE SCREEN ON THE WALL Step 1: Hold up the Fresnel Screen and mark the location of the corners as shown below. If you need a point of reference, turn on your projector and point it towards the wall where you intend to mount your Fresnel Screen.
- Page 18 Step 2: Use an 8mm electric drill to create two pilot holes in the wall. Place each hole 169 mm (6.65 in) down from the upper corners marked on your wall. The left hole should be 563 mm (22.16 in) from the upper left corner and the right hole should be 587 mm (23.11 in) from the upper right corner.
- Page 19 Step 3: Hold up each Wall Mounting Bracket (V) so that the upper left mounting hole lines up with your pilot holes. Mark the wall at the location of the other mounting holes and create new two pilot holes where you marked the wall. Step 4: Hammer the Wall Anchors...
- Page 20 Step 6: Attach the screen to the Wall Mounting Brackets (V). Watch the rear side when hanging the screen. Hang the screen so that the half of the screen labeled THIS WAY UP points is on the bottom. -19-...
- Page 21 Step 7: After the screen is hung on the wall, rotate the Adjustment Rod (W) to adjust the height of the screen to achieve the best display effect. Step 8: Remove the adhesive film from the wall-facing side of the Wall Protectors (U) to fix the bottom of the screen to the wall.
- Page 22 REFERENCE DISTANCE If you purchase Aurora Pro and AS200 / AS400 together, you can refer to the following distances. Please note that these distances are for reference only, as they have been measured manually. The data has been manually tested, and there may be an error of one inch. Please make adjustments according to the actual situation.
- Page 23 PJ92+AS200 Screen / Wall Front View Rear View PJ92+AS400 Screen / Wall Front View Rear View -22-...
- Page 25 Get in touch with FREE online services. facebook.com/letsnexigo...
Need help?
Do you have a question about the ALR-F100 and is the answer not in the manual?
Questions and answers