Subscribe to Our Youtube Channel
Related Manuals for HeatStar 2HSHG10000C
Summary of Contents for HeatStar 2HSHG10000C
- Page 1 OWNER’S MANUAL CEILING MOUNT ELECTRIC HEATER 10,000W / 6,500W | 240V MODEL: 2HSHG10000C...
-
Page 2: Table Of Contents
SAFETY & PRECAUTIONS CONTENTS CONTINUED CONTINUED SAFETY INFORMATION ..............................3 SPECIFICATIONS ................................4 MOUNTING INSTRUCTIONS ............................5 USAGE INSTRUCTIONS ..............................6 INSTALLATION INSTRUCTIONS ..........................7 CONNECTING THE POWER ............................7 SAFETY INSTRUCTIONS ............................... 8 CARE & MAINTENANCE ..............................9 WARRANTY ..................................9 TROUBLESHOOTING ..............................10 HARDWIRED INSTALLATION REQUIRED This heater must be grounded and hardwired to a properly sized current protection circuit breaker in... -
Page 3: General Safety Information
SAFETY INFORMATION INTENDED USE: 7. This heater is not suitable for use in hazardous locations as defined by the National Fire Electric Utility heaters are designed to meet a Protection Association (NFPA) in the United variety of heating requirements. This product States. - Page 4 Do not insert or allow foreign objects to auto-restart is Fahrenheit 80°F/26°C. enter any ventilation or exhaust opening as this may cause an electric shock, fire, or damage the heater. 2HSHG10000C DIGITAL HEAVY DUTY 10,000W ELECTRIC UTILITY HEATER WATTS SWITCH POSITION VOLTS (VAC) PHASE...
-
Page 5: Mounting Instructions
MOUNTING INSTRUCTIONS Figure 1 NOTE: Diagram is not drawn to scale, for information purposes only. NOTE: Product dimensions are approximate and subject to change without notice. WARNING FOR INDOOR USE ONLY, IN A DRY LOCATION FREE OF GASOLINE, PAINT, FLAMMABLE LIQUIDS OR COMBUSTIBLE DUST OR MATERIALS. -
Page 6: Usage Instructions
USAGE INSTRUCTIONS OPERATION AND TEMPERATURE TIMER FUNCTION: SETTING The Timer function allows you to set the length of operation from1 to 12 hours. Each time the TIMER 1. This heater is designed to maintain a button is pressed the length of operation will comfortable room temperature. -
Page 7: Installation Instructions
INSTALLATION AND CONNECTING POWER BRACKET INSTALLATION CONNECTING THE POWER Refer to Figure 4. 1. With the power off at the breaker, remove all screws from the bottom lid for access to the 1. Locate a ceiling joist or other firm structural electrical section of the heater. -
Page 8: Adjusting Air Flow
CONNECTING THE POWER (Continued) ADJUSTING AIR FLOW 3. Pull enough wire into the heater and connect to wire to the Power Block located in the 1. Tilt the unit–Loosen the top Small Knob- electrical area of the heater (See Figure 7). Screws and thread into provided holes in 4. -
Page 9: Care & Maintenance
PURCHASING in any respect which in our judgment affects Accessories may be purchased at any HeatStar its condition or operation. Some states do not local dealer or direct from the factory. -
Page 10: Troubleshooting
TROUBLESHOOTING POSSIBLE CLEARING ERROR ERROR CODE RECOMMENDED SOLUTION CAUSE CODES Ensure Heater is Installed with Sufficient Clearance All-Around, See Figure 1. Insufficient • 6 feet minimum mounting from floor Clearance Around Heater • 8 inches minimum from rear of heater •... - Page 11 TROUBLESHOOTING (Continued) POSSIBLE CLEARING ERROR ERROR CODE RECOMMENDED SOLUTION CAUSE CODES Disconnect power! Detach Fan Grille by removing screws. Locate Temp Sensor Thermocouple on Housing (below Fan Motor Bracket). Ensure Detached wire pair and thermocouple “tip” are free or Loose of damage.
- Page 12 ENERCO GROUP, INC. 4560 W. 160TH ST. CLEVELAND, OHIO 44135 866-447-2194 Heatstar is a registered trademarks of Enerco Group, Inc. © 2024, Heatstar. All rights reserved. Printed in China 0424_M009...
Need help?
Do you have a question about the 2HSHG10000C and is the answer not in the manual?
Questions and answers