Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Atlantic BOOST
Summary of Contents for Atlantic BOOST
- Page 1 MADE IN ITALY BOOST Installation ad use manual 0,37÷15 RANGE 0,50÷20...
- Page 2 Index BOOST Introduction 1.1 PRESENTATION pag. 3 1.2 DESCRIPTION pag. 3 1.3 HANDLING pag. 3 Safety informations 2.1 WARNINGS pag. 4 2.2 CAUTION pag. 4 Installation 3.1 ASSEMBLING pag. 5 3.2 ELECTRICAL CONNECTIONS pag. 6 BOOST 3.3 INITIAL VIEWS pag. 8 3.4 ADJUSTMENTS AND SETTINGS...
- Page 3 The instruction and warnings given below concern the standard version; refer to the sale 1.2 DESCRIPTION BOOST is an electronic panel for direct start-up of operating programs for clean water, waste of 2 single-phase or three-phase pumps with water and minimum level management with over current and dry running protection.
-
Page 4: Safety Information
• (400V ± 10% 50/60Hz x il BOOST -400/...) protected. The line must be protected with an • (230V ± 10% 50/60Hz x il BOOST -230) Earth leackage and magnetic switch measured in accordance with the regulations locally in force. -
Page 5: Installation
Installation BOOST 3.1 ASSEMBLING Fix the control panel for a stable support with If use an electric screwier pay attention not to screws and screw anchor using the holes spoil the thread or the screws. arranged in the box. After the fixing, remove every plastic or metallic To fix the cables in their terminals use a tool surplus (ex. -
Page 6: Electrical Connections
Installation BOOST 3.2 ELECTRICAL CONNECTIONS BOOST 230 display N L C N L C 1 2 3 C Alarm output selector (J2/J3) 12 Vcc output free contact N.O. 230 V 50÷60 Hz... - Page 7 Installation BOOST BOOST 400 display 1 2 3 C Alarm output selector (J2/J3) 12 Vcc output free contact N.O. 400 V 50÷60 Hz...
- Page 8 (P1 and P2). IMPORTANT! The BOOST control panel is not intended as a reading instrument, therefore the value of the current absorption detected and shown on the display may differ from the actual value by ±10%. For an accurate verification of the current absorption, use a suitable reading instrument.
-
Page 9: Adjustments And Settings
Installation BOOST 3.4 ADJUSTMENTS AND SETTINGS PARAMETERS SETTING AND CONTROL PANEL OPERATIVITY TRIMMER 1 TRIMMER 2 TRIMMER 3 To set the maximum absorbed current parameters At the end of this phase, by pressing the “AUT” (pump 1 and pump 2) and the sensitivity of the... -
Page 10: Dip Switch Setting
Installation BOOST 3.5 DIP-SWITCH SETTING SW1 DIP-SWITCH DIP-SWITCH 1 - PROGRAM SELECTION The panel is set as standard with dip-switch 1 in the “OFF” position. To access the menu and select the programs on display, set dip-switch 1 to the “ON” position with the panel on (see “PROGRAMS SETTING”). -
Page 11: Programs Setting
Installation BOOST 3.6 PROGRAMS SETTING ACCESS TO PROGRAMS DIP-SWITCH 1 To access the menu and select the programs on display, set dip-switch 1 to the “ON” position with panel on. PROGRAMS SETTING To select the program to be set, scroll through the sequence with the “AUT”... - Page 12 Installation BOOST PROGRAM DESCRIPTION PUMP 1 MAXIMUM CURRENT (default: 10A) Setting of the threshold value of the maximum absorbed current, below which the panel intervenes stopping the pump 1 and activating the alarms. CHANGE PUMP 1 MAXIMUM CURRENT 1 0 0...
- Page 13 Installation BOOST PROGRAM DESCRIPTION CLEAN WATER (DEFAULT) Preset program for operation with pressure switches, floats for clean water or CLC level probes (see application example 1). WASTE WATER Preset program for operation with floats for waste water or CLC level probes (see application example 2).
- Page 14 Installation BOOST 3.7 TRIMMER SETTINGS If you want to modify the threshold value of PROTECTION DELAY the maximum motors absorbed current or the The pumps protections switching sensitivity of the CLC input level probes, you delay has been set at 5 sec.
-
Page 15: General Use
General use BOOST 4.1 KEYPAD AND LIGHTS INDICATIONS BOOST CONTROL PANEL blue light indicating power network presence and powered panel. ALARM red light to indicate a general alarm and pump stop (min and max Amp, min or max level and dry running). - Page 16 General use BOOST 4.2 ALARMS LED SIGNALING DEACTIVATION All alarms are displayed on the If the panel is in alarm and you control panel (red led flashing) and want to silence it, press the “0” activate the following outputs: button twice.
- Page 17 General use BOOST DISPLAY ALARMS To view the type of alarm, turn off the ignition, The display will show the alarm code present open the door and turn it on again. (see table below). CODE ALARM CODE ALARM AL 1...
-
Page 18: Typical Installations
General use BOOST 4.3 TYPICAL INSTALLATIONS EXAMPLE 1 p 3 o n p 4 o f f p 5 o f f start/stop start/stop G1 optional, if not used it must be jumpered. Pr 1 Pr 2 start/stop start/stop start... - Page 19 General use BOOST EXAMPLE 2 p 3 o f f p 4 o n p 5 o f f start start stop EXAMPLE 3 p 3 o f f Pr 1 Pr 2 start/stop start/stop p 4 o f f p 5 o n G1 optional, if not used it must be jumpered.
-
Page 20: Maintenance
“0” button. Turning the main switch interlocking door in “OFF” position. 5.2 SERVICE BOOST does not require any routine maintenance DANGER! provided that their working limits are observed. Make sure that BOOST is... -
Page 21: Certificate Of Conformity
Atlantic Power Control S.r.l.s Via E. Fermi, 10 - 35020 Polverara (PD) - ITALY DECLARES UNDER IS OWN RESPONSIBILITY THAT THE FOLLOWINGS CONTROL PANELS: BOOST -230 e BOOST -400 ARE IN CONFORMITY WITH COMMUNITY DIRECTIVES REGARDING: • European • Electromagnetic... - Page 22 Notes BOOST...
- Page 23 Notes BOOST...
- Page 24 ATLANTIC POWER CONTROL S.r.l.s. Via E. Fermi, 10 35020 Polverara (PD) Italy Tel +39 0495855425 CERTIFIED www.atlanticontrol.com 9001 - 14001 45001 info@atlanticontrol.com...
Need help?
Do you have a question about the BOOST and is the answer not in the manual?
Questions and answers