Subscribe to Our Youtube Channel
Related Manuals for MPS MEDACURE LINCOLN EXPANDABLE BED
Summary of Contents for MPS MEDACURE LINCOLN EXPANDABLE BED
- Page 1 U S E R M A N U A L Lincoln Expandable Bariatric Bed FOR SERIES MODEL # LX-BARI & LX-BARI-9 IMPORTANT: CHECK THE LABEL ON THE BED FRAME FOR THE CORRESPONDING MODEL NUMBER ©2022 Made in China...
-
Page 2: Table Of Contents
Table of Contents Introduction & Product Features ..................3 Parts List & Description ....................4 Installing The Lifting Frame & Height Adjustment Motor ......................5 Installing the Length Extension Frame ................6 Installing the Bed Boards .....................7-8 Casters ..........................9 Bed Width Extension ....................9-10 Bed Length Extension ....................10 Corner Matress Retainer ....................11 Bumper Guard Installation &... -
Page 3: Introduction & Product Features
Introduction MEDACURE LINCOLN EXPANDABLE BED is a fully electric, versatile and multi-functional bed for Long Term Care, Hospital & Homecare settings. It expands in both the width (from 36” to 48”) and length (from 80” to 88”) which makes it ideal for standard, bariatric and tall patients. The LX-BARI has a low position of 14.9” and 5 patient position functions to enhance the quality of care and for ultimate comfort. -
Page 4: Parts List & Description
Parts List & Description IMPORTANT: Read this manual completely before setting up or operating this system and keep in a safe place for future reference. To avoid injury and for maximum safety, this system should only be installed by an authorized technician or dealer representative. ELECTRIC BED INSTALLATION PARTS LISTED BELOW AS PER FIGURE # 1 Bed Frame Bed Foot Board... -
Page 5: Adjustment Motor
Installations 1. INSTALLING THE LIFTING FRAME Remove the φ13.5 bolt from the lifting frame (1). Place a φ 14 plastic washer between the lifting frame (1) and lifting frame (2), matching the bolt holes on both lifting frames. Fasten with a φ 13.5 bolt with cotter pin as per Figure # 2. Use 4 bolts to connect the lifting frames. -
Page 6: Installing The Length Extension Frame
Installations 3. INSTALLING THE LENGTH EXTENSION FRAME 3.1. Insert extension frame (left) & extension frame (right) into the 60 x 30 mm rectangular bedframe tube. See Figure #4 The extension frame tubes should face upward. FIGURE #4 Insert the extension frame, tighten the bolt to lock the extension frame, and then fix the plastic head bolt. -
Page 7: Installing The Bed Boards
Installations 4. INSTALLING THE BED BOARDS 4.1. Press the M8 × 18 plate nut into the bed board holes, as per Figure # 6. 4.2.1 Match the bed head board with the bed frame installation holes. Fasten by M8 X 20 cup head bolt with φ 8 flat washer, as per Figure # 7. - Page 8 Installations Match the bed foot board with the extension frame installation holes. Fasten by M8 X 20 cup head bolt with φ 8 flat washer. Bed foot board can be installed in both the high and low level position. See Figure # 8 & Figure # 9. FIGURE #8 Bed foot board in low-level FIGURE #9...
-
Page 9: Casters
Installations 5. CASTERS There are 4 pcs. locking casters and 4 pcs. swivel casters per set. Step on the locking pedal (lower) to activate the locking position and step on the unlocking pedal (upper) to deactivate the locking system. See Figure # 12 & 13. Step on the pedal to Step on the pedal lock the caster in place... -
Page 10: Bed Length Extension
Installations IMPORTANT NOTE: There are 3 location holes on each extension frame for 3 width adjustment settings - 36”, 42” and 48” widths. There are 4 separate extension frames on each side of the main frame. Repeat the above method in 6.1 to achieve the desired width and then tighten the “Locking Bolt”... -
Page 11: Corner Matress Retainer
Installations 8. MATRESS RETAINERS Each corner of the bed frame has two mattress retainer installation holes. Insert the mattress retainer as noted in Figure # 16.1. Mattress Retainer Installation for Mattress Retainer Installation for Standard Bed Deck Expandable Bed Deck FIGURE #16.1 9. - Page 12 Installations 9.2 Extended Position: Push the bumper guard stem upward and turn the stem outward until the screw clicks with slot as noted in Figure # 16.3. FIGURE #16.3 9.3 Retracted Position: when bumper guard is not in use, push the stem upward and turn it inward until screw clicks with slot as noted in Figure # 16.4 FIGURE #16.4 10.
-
Page 13: Patient Remote Controls
Installations 11. PATIENT REMOTE CONTROL Raise Bed Head Part Lower Bed Head Part Raise Bed Foot Part Lower Bed Foot Part Raise Both Bed Lower Both Bed Head and Foot Part Head and Foot Part Raise The Entire Bed Lower The Entire Bed Trendelenburg ReverseTrendelenburg FIGURE #17...
Need help?
Do you have a question about the MEDACURE LINCOLN EXPANDABLE BED and is the answer not in the manual?
Questions and answers