Page 3
Welcome aboard your vehicle This user manual contains the information required: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to fully benefit from the all the functions and the technical developments it incorporates. –...
EXTERIOR 1 4 - We l c o m e a b o a r d y o u r v e h i c l e...
Page 7
EXTERIOR 1. Electric windows 317 1 Window wipers 152 Demisting 307 2. 50 card Locking/unlocking the doors 62 3. Rear view mirrors 141 4. Bodywork maintenance 340 5. Tyres 344 6. Lights: operation 143 Lights: replacement 361 We l c o m e a b o a r d y o u r v e h i c l e - 5...
PASSENGER COMPARTMENT 1 6 - We l c o m e a b o a r d y o u r v e h i c l e...
Page 9
PASSENGER COMPARTMENT 1. Adjusting your driving position 80 1 2. Passenger compartment storage/fittings 322 3. Rear headrests 78 Rear bench seat 78 4. Luggage compartment storage/fittings 328 5. Child safety 94 6. Front headrests 73 Front seats 73 We l c o m e a b o a r d y o u r v e h i c l e - 7...
SAFETY ON BOARD 1 1 2 - We l c o m e a b o a r d y o u r v e h i c l e...
Page 15
SAFETY ON BOARD 1. Airbags Front 85 1 2. Airbags Central 91 3. Airbags Curtain 91 4. Seat belts 80 5. Airbags side 90 We l c o m e a b o a r d y o u r v e h i c l e - 1 3...
IDENTIFYING A VEHICLE - LABELS 1 1 4 - We l c o m e a b o a r d y o u r v e h i c l e...
Page 17
IDENTIFYING A VEHICLE - LABELS 1. Vehicle identification plate 375 1 2. Vehicle identification number reminder 375 3. Tyre pressure label 346 4. Engine identification plate 376 5. Technical information for the emergency services 375 We l c o m e a b o a r d y o u r v e h i c l e - 1 5...
THE ENGINE COMPARTMENT (ROUTINE MAINTENANCE) 1 1 6 - We l c o m e a b o a r d y o u r v e h i c l e...
Page 19
THE ENGINE COMPARTMENT (ROUTINE MAINTENANCE) 1. Coolant 335 1 2. Brake fluid 337 3. Remote battery terminals 339, 24, 29, 357 4. Opening the bonnet 331 5. Engine oil dipstick 332 6. Engine oil filler cap 332 7. Screen washer fluid 338 We l c o m e a b o a r d y o u r v e h i c l e - 1 7...
THE E-TECH FULL HYBRID VEHICLE 1 2 0 - We l c o m e a b o a r d y o u r v e h i c l e...
Page 23
THE E-TECH FULL HYBRID VEHICLE E-Tech full hybrid vehicle system: introduction 24 1 E-Tech full hybrid vehicle system: important recommendations 28 1. Warning lights 134 Displays and indicators 127 Power meter 180 2. Parking aids 268 3. Regenerative braking change paddles 167 4.
E-TECH FULL HYBRID VEHICLE (HEV) Introduction 2 2 4 - G e t t i n g t o k n o w y o u r v e h i c l e...
Page 27
E-TECH FULL HYBRID VEHICLE (HEV) As with any battery, it discharges when the warning light is displayed in blue 1. "12 Volt" battery 127. it is used. The traction battery is 2. Orange electrical power cables charged: Failure to do so may result in damage 2 ...
Page 28
E-TECH FULL HYBRID VEHICLE (HEV) Note: the "12 V" battery does not help to start the combustion engine. This is As your E-Tech full hy- provided by the E-Tech full hybrid sys- brid vehicle is silent, 2 tem. when leaving it always engage the gear in Ppo- "400 V" electrical circuit sition, apply the parking brake and switch off the ignition.
Page 29
E-TECH FULL HYBRID VEHICLE (HEV) Operation These are energy flows between: This is used to brake the vehicle and recharge the traction battery. – B : the combustion engine; The E-Tech full hybrid system selects – C : the electrical assembly (traction the combustion engine and/or the elec- All-electric driving mode 2 ...
Page 30
E-TECH FULL HYBRID VEHICLE (HEV) Important recommendations 2 Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious in jury or electric shocks which could result in death. In the event of an accident or impact In the event of an accident or an impact to the underside of the vehicle (e.g.
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Introduction 2 G e t t i n g t o k n o w y o u r v e h i c l e - 2 9...
Page 32
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) – your vehicle's charging status with – during deceleration phases; 1. Electric charging connection low battery warning; – with the combustion engine starting 2. Secondary 12 V battery – the traction battery charging pro- automatically, even at idle speed, to 2 gramming, based on certain choices act as a generator and maintain the...
Page 33
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) "400 V" electrical circuit equipment (lights, windscreen wipers, braking assistance, etc.). The drive system of the rechargeable hybrid ve- 2 hicle uses direct current of approximately 400 V. This system can get hot during and after switching off the ignition. Observe the warning messages on the labels in the vehicle.
Page 34
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) pedal, the motor generates electrical mode. You will not yet necessarily be For further information on the pedestri- current during deceleration and this used to it, and neither will other road an horn, refer to the multimedia in- energy is used to brake the vehicle users. It is difficult for them to hear the structions.
Page 35
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Energy flow is using only the electrical assembly to power the vehicle movement. 2 Regenerative braking level warning light D Depending on the driving mode select- When you lift your foot off the acceler- When the hybrid system is using the ed, the various energy flows are ator pedal or when you press on the combustion engine with or without the shown on the instrument panel.
Page 36
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Press switch 8 as many times as re- "E-Save" mode from the outset, espe- message disappears from the instru- quired to exit "Electric" mode. cially in the event of a rough road sur- ment panel. face. The "Electric" message disappears 2 Activation, deactivation of "E- along with the warning light from Save" mode the instrument panel. Note: when the traction battery level is low, the vehicle automatically switches to hybrid mode and the combustion...
Page 37
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Important recommendations 2 Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious in jury or electric shocks which could result in death. In the event of an accident or impact In the event of an accident or an impact to the underside of the vehicle (e.g.
Page 38
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Risk of electric shock and a risk to life. 2 3 6 - G e t t i n g t o k n o w y o u r v e h i c l e...
Page 39
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Charging 2 Schematic diagram G e t t i n g t o k n o w y o u r v e h i c l e - 3 7...
Page 40
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) 1 Specific wall socket or recharging terminal 2 Charging cable 2 3 Electric charging connection (pas- senger side) If you have any questions regarding the equipment needed for charging, please ask an authorised dealer. 3 8 - G e t t i n g t o k n o w y o u r v e h i c l e...
Page 41
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Important recommendations for charging 2 Important recommendations for charging your vehicle Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious in jury or electric shocks which could result in death. Charging Do not do anything to the vehicle during charging (washing, working in the engine compartment, etc.).
Page 42
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Depending on the vehicle, either the Charging cords 10 A or 16 A cable can be used for: – in normal use, on a socket used only Charging lead A 2 for the vehicle (14 A/16 A charging); –...
Page 43
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Charging cable B Before cleaning the charg- ing cable, make sure it is 2 disconnected. Clean the cable using a cloth slightly dampened with water. When cleaning, make sure that the cloth does not come into con- tact with the ends of the cable (connectors, charging pins) to avoid any risk of corrosion.
Page 44
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Important recommendations 2 Important recommendations for charging your vehicle Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious in jury or electric shocks which could result in death. Choice of charging cord The standard charging cords supplied with the vehicle have been designed specifically for this vehicle. It is designed to pro- tect you against the risks of electric shock that can lead to death or fire.
Page 45
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Charging types that conform to Eu- ropean standards 2 Alternating current (AC) If the information is displayed on the vehicle charging flap, follow the in- structions below. Before plugging in a charging lead, check that: – the colour and one of the letters of the input socket 1 correspond to the colour and one of the letters on the end 4 of the lead;...
Page 46
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Labels Charging type Alternating current ( AC ) 2 Charging terminal 1 /Charging Connection Vehicle 3 /Charging lead 5 lead 4 Charging types that conform to European standards (for all other cases, please consult an approved dealer).
Page 47
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) period of time or even become impos- – The button 7 launches imme- Electric charging socket 3 sible. diate charging of the vehicle; It is preferable to recharge the vehicle 2 Precautions after driving if the charge level is low (< 25%) and in negative temperatures. Avoid charging and parking your vehi- cle in extreme temperatures (hot or Advice...
Page 48
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) – press the charging flap 8 to unlock The charging cord is automatically it. The warning light 9 illuminates in locked with the vehicle. This will make white; it impossible to unplug the cord from 2 your vehicle.
Page 49
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) The display on the instrument panel One charging is complete, the warning – Press the button 6 or press and light 9 illuminates continuously in disappears after a few seconds. It hold the door unlocking button on the reappears on the instrument panel green.
Page 50
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) Label 13 – when it lights up continuously in red Charging programming this indicates an operating fault. The label 13 located on the right-hand 2 side reminds you of the following in- structions: – do not wash the charging flap using a high-pressure water jet;...
Page 51
E-TECH PLUG-IN HYBRID VEHICLE (PHEV) With the vehicle stationary and the en- gine on, from the "Vehicle" world 2 on If you have just accepted a the multimedia screen 1 , press the system update via the mul- "Electric" menu 3 then the "Charging & 2 timedia system, the traction Air conditioning"...
CARD – automatic remote opening/closing of beep sounds and the hazard warning the electric windows 317. General information lights and side repeaters do not flash. 2 Depending on the vehicle, If the battery is flat, you can you may have a digital key still lock/unlock and start your vehicle 62 160.
Page 53
CARD Fitting a hand strap 7 Press and hold button 4 for approxi- use of equipment operating on the mately two seconds to switch on the same frequency as the card) may dis- exterior lighting and emit a sound. rupt its operation. 2 Note: press button 4 again to switch off the lighting.
Page 54
CARD Deactivating/activating the "hands- Insert the hand strap into the compo- nent 8 and pass the end of the strap free mode" Driver's responsibility through the buckle. when parking or stop Depending on the vehicle, you can de- 2 Position the strap at the opening 6 and ping the vehicle activate/activate unlocking when ap- close the casing. Never leave an animal, proaching and locking when moving away from the vehicle.
Page 55
CARD "Hands-free" unlocking when ap- "Hands-free" locking when moving proaching the vehicle away from the vehicle 2 If the card has been within the detec- tion zone 1 for approximately 15 min- utes, remote locking is deactivated. To If the card is in the access zone 1 the With the card on you and the doors lock the vehicle, press the button 3 on vehicle will be unlocked.
Page 56
CARD "Hands-free" unlocking by opening Using the card as a remote control – if the card remains close to vehicle the luggage compartment zone 2 during approximately five min- utes after the vehicle has been un 2 locked; – after several passes in the vicinity of zone 2 without the doors having been opened.
Page 57
CARD Locking using the card Deadlocking With the doors and luggage compart- ment door closed, press button 3 : the 2 vehicle will be locked. The hazard warning lights flash twice to indicate that the vehicle is locked and, depending on the vehicle, the door mirrors automatically fold in. Depending on the vehicle, press and hold button 3 to lock the vehicle and close the front and rear windows.
Page 58
CARD The hazard warning lights and side in- Battery dicator lights give two slow flashes and three quick flashes to confirm Replacing the battery 2 locking. Depending on the vehicle, the door mirrors may fold in automatically when the vehicle is locked 141. To deactivate deadlocking Press button 1 once.
Page 59
CARD If they need to be re- Precautions relating to placed, be sure to use batteries: 2 the same or equivalent – keep batteries (new or type of battery (consult used) out of reach of children; an Approved Dealer). – do not swallow batteries; Risk of chemical burns which may lead to death.
DIGITAL KEY Depending on the country and sub- Secure access to the digi The digital key's operational scription, you can install a digital key tal key on the smart reach will depend on your for your vehicle on your smartphone. 2 phone smartphone's Bluetooth® The digital key contains the rights re- It is the responsibility of the owner connection.
Page 61
DIGITAL KEY the internet throughout the procedure seconds for the vehicle to identify the Starting, stopping the engine (via Wi-Fi or mobile networks); digital key installed on your smart- – the occasional user's digital key is phone. activated once the procedure is com- 2 From your smartphone, with Blue- pleted. tooth® activated, open the manufacturer's application and discov- Revoking a digital key er the various functions available for...
Page 62
DIGITAL KEY For more information, please refer to mobile network) at least once every 48 the information on "Starting, stopping hours. Otherwise, connect your smart- the engine" 160. phone to the internet for a few minutes 2 so that the digital key can be reactivat- The smartphone must remain in the vehicle throughout the journey.
DOORS AND OPENING ELEMENTS Opening from the inside Opening and closing the doors 2 Opening from the outside Rear doors With the doors unlocked or the card on Pull the handle 3 . you, hold the handle 2 and pull it to- Depending on the vehicle, it may be wards you.
Page 64
DOORS AND OPENING ELEMENTS Child safety ing buzzer will sound when a door is opened. Driver's responsibility when parking or stop 2 Door or luggage compartment lid ping the vehicle open buzzer Never leave an animal, With the vehicle stationary and the ig- child or adult who is not self-suffi- cient alone in your vehicle, even nition on, the warning light ap- for a short time.
Page 65
DOORS AND OPENING ELEMENTS The card's built-in key Using the key integrated in the – the vehicle is located in a high elec- card tromagnetic radiation zone; – vehicle locked using a digital key 58. 2 The built-in key 2 can be used to lock or unlock the driver's door when the –...
Page 66
DOORS AND OPENING ELEMENTS Locking the doors manually Interior locking/unlocking door con- Door and tailgate status indicator trol With the ignition on, the switch 6 warning light indicates the locking sta- 2 tus of the opening elements: – when the warning light is on, the doors and luggage compartment door are locked;...
Page 67
DOORS AND OPENING ELEMENTS When the door is closed, all the doors you reach approximately 6 mph (10 ments are properly closed. If they are and tailgate will be locked. km/h). properly closed, contact an approved dealer. Note: it is only possible to unlock the The door can be unlocked: 2 ...
Page 68
DOORS AND OPENING ELEMENTS Opening manually from inside the Luggage compartment vehicle The attaching of any car- To open rying device (bike rack, 2 luggage box etc.) resting on the luggage compart- ment lid is prohibited. To install a carrying device on your vehicle, contact an approved dealer. Automatic tailgate Conditions of use –...
Page 69
DOORS AND OPENING ELEMENTS using the remote control card Using the exterior opening control Ensure that nobody is close to the moving parts 2 when opening/closing the tailgate. Risk of injury. Depending on the equipment, the tail- gate locks and unlocks at the same time as the doors. There are various ways to handle the tailgate: –...
Page 70
DOORS AND OPENING ELEMENTS Using the tailgate interior closing Using the dashboard control control 2 The "hands-free" function enables al- lows you to access the luggage com- To open the tailgate, press and hold partment when you have your hands Press the control 3 . the switch 4 until you hear the sound full.
Page 71
DOORS AND OPENING ELEMENTS Obstacle detection the closure (a beep is emitted every second). Deactivate the "hands- If the tailgate detects an obstacle dur- free" function before Activation/deactivation of the ing its manoeuvre then it will stop. It 2 "hands-free" function you: will then be released from the obstacle following a small movement in the op- (depending on the multimedia system) –...
Page 72
DOORS AND OPENING ELEMENTS Limiting the tailgate opening angle sufficient to allow the tailgate to oper- The obstacle detection is ate. – Avoid multiple manual stops during an aid to opening and 2 the automatic tailgate movement (risk closing the tailgate, it of damaging the tailgate system). does not in any way re- –...
Page 73
DOORS AND OPENING ELEMENTS Driver's responsibility when parking or stop 2 ping the vehicle Never leave your vehicle with a child, an adult who is not self-sufficient or a pet inside or at the rear of the tailgate, even for a short while.
FACIAL RECOGNITION If the face image is not recognised by the camera during recognition, the sys- tem suggests the last profile used. 2 Note: make sure that the camera is not obscured (by dirt, mud, etc.). When recalling a posi- tion (memorisation, changing profile), make sure that no one is near the moving parts (in particular, in the rear seats).
FRONT SEATS To move it backwards, press the but- Front seats with manual control Front headrests ton 1 and push it backwards. To move the seat forwards or back Note: it is not possible to remove the 2 To raise the headrest front headrests. Raise the handle 1 to unlock. Release Pull the headrest upwards to the de- the handle at the desired position and sired height.
Page 76
FRONT SEATS Front seats with electric con- Move lever 2 as many times as neces- – an initial press on the pictogram sary upwards or downwards. trols of the desired seat activates the heating system at maximum power. 2 To tilt the seatback Three switch-integrated warning lights Lift handle 3 and tilt the seatback to are illuminated;...
Page 77
FRONT SEATS Adjusting the seat position Heated seats For safety reasons, carry out any adjustments 2 while the vehicle is sta- tionary. We would advise you not to re- cline the seatbacks too far to en- sure that the effectiveness of the seat belts is not reduced. Nothing should be placed on the floor (area in front of the driver) as these objects may slide under the pedals during sudden braking ma- noeuvres, thus obstructing their...
Page 78
FRONT SEATS Operating faults You can activate the " Massage " func- tion (Active Lumbar) on the driver's If an operating fault is detected, the seat or, depending on the vehicle, on warning lights on the pictogram for the 2 the front passenger seat. seat concerned will flash on the multi- media screen 5 . Consult an approved dealer.
Page 79
FRONT SEATS Press and hold the switch 1 of the seat on which you would like to acti- Deactivate the "Easy Ac- vate the "Massage" function, according cess Seat" function be- to the defined parameters. 2 fore installing a child seat on the front passen- Settings ger seat and/or on the rear seats. Refer to the multimedia instructions for Risk of injury.
REAR SEATS To remove the headrest Rear bench seat Rear headrests Functions 2 Position for use Pull on strap 1 to tilt the bench seat- back forwards, then remove the head- rest. To fold down the seatback The side headrests and centre head- To refit the headrest rest are not adjustable. Ensure that the front seats are far enough forward.
Page 81
REAR SEATS Central rear armrest Raise the seatback again until it reach- es the locking joint of the seatback. Be careful not to jam the seat belt be- tween the seatback and the parcel 2 shelf. Check the operation of the seat belt. When refitting the seat back, make sure it is correctly locked in place. If seat covers are fit...
SEAT BELTS Adjusting the seat belts Seat belts Make sure that the rear bench seat 78 is locked Always wear your seat belt when trav- 2 in position correctly so that elling in your vehicle. You must also the rear seat belts will operate comply with the legislation of the par- correctly. ticular country you are in.
Page 83
SEAT BELTS The seat belt must be worn as close to With the doors closed, the graphic 6 is the body as possible. e.g. avoid wear- displayed on the instrument panel for ing heavy clothing, keeping bulky ob- approximately 60 seconds when the jects under the belts, etc. vehicle ignition is switched on. This in- 2 forms the driver of the fastening status Locking of each of the front seat belts every time:...
Page 84
SEAT BELTS When the vehicle speed exceeds ap- – the doors are opened during driving proximately 12 mph (20 km/h), if one (vehicle speed above zero); – a beep sounds for around 30 or 120 – a front seat belt is fastened/unfas- of the front seat belts is or becomes seconds;...
Page 85
SEAT BELTS Adjusting the height of the front Rear side seat belts 8 Rear centre seat belt 9 seat belts 2 The belts are fastened, unfastened Slowly unwind the belt 9 . Press the button 7 to adjust the seat and adjusted in the same way as the Fasten the buckle 10 into the red belt height, so that the shoulder strap...
Page 86
SEAT BELTS Warnings The following information applies to the vehicle’s front and rear seat belts. 2 – No modification must be made to the originally-fitted restraint system components (seat belts, seats and their mountings). For special operations (e.g. fitting a child seat), please contact an approved dealer. –...
ADDITIONAL SAFETY DEVICES Pretensioners Methods of restraint in addition – Have the entire re- to the front seat belts straint system checked 2 following an accident. Depending on the vehicle, they may comprise: – No operation whatsoever is per- mitted on any part of the system – seat belt inertia reel pretension (pretensioners, airbags, comput- ers;...
Page 88
ADDITIONAL SAFETY DEVICES Driver and passenger front airbags This system is only operational when The airbag system uses the ignition is switched on. Fitted to the driver and passenger pyrotechnic principles. In a severe frontal impact, the airbags sides. 2 This explains why, when inflate rapidly, cushioning the impact of A symbol on the lower section of the...
Page 89
ADDITIONAL SAFETY DEVICES 2 The following cases trigger the pre In the event of a frontal impact with In a side impact with another vehi tensioners or airbags . another vehicle of an equivalent or cle of an equivalent or higher cate higher category, with an impact area gory, at an impact speed equal to or In a frontal impact against a rigid...
Page 90
ADDITIONAL SAFETY DEVICES 2 The pretensioners or airbags may be In the following cases, the preten – side impact at the front or rear of the triggered in the following cases: sioners or airbags might not be trig vehicle; gered: –...
Page 91
ADDITIONAL SAFETY DEVICES Warnings All of the following warnings are intended to ensure that the airbag is not obstructed in any way when it is inflated and 2 also to prevent the risk of serious injury caused by objects which may be projected when it inflates. Warnings in relation to the driver's airbag –...
Page 92
ADDITIONAL SAFETY DEVICES Side seat belt pretensioners Methods of restraint in addition – Have the entire re- to the rear seat belts straint system checked 2 following an accident. Depending on the vehicle, they may comprise: – No operation whatsoever is per- mitted on any part of the system –...
Page 93
ADDITIONAL SAFETY DEVICES side of the seats to protect the occu- pants in the event of a severe side im- pact. 2 Curtain airbag This airbag fitted (depending on the vehicle) along the upper sides of the vehicle – they inflate along the front and rear door side windows to protect the passengers in the event of a se- vere side impact. Central airbag This airbag fitted to the driver's seat and deployed between the driver's seat and the passenger seat in order to protect the driver and passenger in...
Page 94
ADDITIONAL SAFETY DEVICES Warnings 2 Warning relating to the passengerairbag side airbag and theairbagcentral airbag – Fitted with covers: seats equipped with anairbag require vehicle-specific covers. Contact an approved dealer to find out if these covers are available. The use of any covers other than those designed for your vehicle (includ- ing those designed for another vehicle) may affect the operation of the airbag and compromise your safety. –...
Page 95
ADDITIONAL SAFETY DEVICES Additional methods of restraint All of the following warnings are intended to ensure that the airbag is not obstructed in any way when it is inflated and 2 also to prevent the risk of serious injuries caused by items which may be projected when it inflates. The airbag is designed to complement the action of the seat belt.
CHILD SAFETY General information A collision at 31 mph (50 Driver's responsibility km/ h ) is the same as when parking or stop 2 Carrying children falling a distance of 10 ping the vehicle metres. Transporting a Never leave an animal, Please ensure that you comply with child without a restraint is the child or adult who is not self-suffi- the legislation of your country.
Page 97
CHILD SAFETY proved Dealer to find out which seats are recommended for your vehicle. Set a good example by al- Never leave a child unat- ways fastening your seat tended in the vehicle. The regulations on transporting chil- 2 dren are specific to each country. The belt and teaching your Check that your child is use of a child seat depends on the age child: always strapped in and...
Page 98
CHILD SAFETY Forward-facing child seats Booster cushions Choosing a child seat Rear-facing child seats 2 Up to 18 kg or 4 years, the child may From 15 kg or 4 years, the child can travel on a forward-facing seat. travel using a booster seat, which will Choose a seat according the child's enable the seat belt to be adapted to A baby’s head is, proportionally, heav-...
Page 99
CHILD SAFETY Choosing a child seat mounting In the latter three cases check that The seat belt must never your child seat can be installed by con- There are two ways to attach child sulting the list of compatible vehicles. be twisted or the tension seats: using the seat belt or using the 2 ...
Page 100
CHILD SAFETY The ISOFIX anchorage points have been exclu- 2 sively designed for child seats with the ISOFIX system. Never fit a different type of child seat, seat belt or other ob- jects to these fittings. Check that nothing is obstructing the anchorage points. If your vehicle has been involved in a road accident, have the ISOFIX anchorage points checked and replace your child...
Page 101
CHILD SAFETY The ISOFIX anchorage points have been exclu- 2 sively designed for child seats with the ISOFIX system. Never fit a different type of child seat, seat belt or other ob- jects to these fittings. Check that nothing is obstructing the anchorage points. If your vehicle has been involved in a road accident, have the ISOFIX anchorage points checked and replace your child...
CHILD SEATS ent child seat, check with the manufac- Fitting a child seat, general in- turer that it can be fitted. RISK OF DEATH OR formation SERIOUS INJURY: be- In the front seat 2 fore fitting a rear-facing The laws concerning children travelling Some seats are not suitable for fitting child seat on the front in the front passenger seat differ in child seats.
Page 103
CHILD SEATS Ensure that the child Fitting a seat ISOFIX in seat or the child's feet do the rear-left seat means 2 not prevent the locking in the middle seat cannot place of the seat in front be used. The central 78 and 73.
Page 104
CHILD SEATS Attachment by seat belt 2 Fitting diagram 1 0 2 - G e t t i n g t o k n o w y o u r v e h i c l e...
Page 105
CHILD SEATS RISK OF DEATH OR SERIOUS INJURY: before fitting a rear facing child seat on the front passenger seat, check that the airbag has been deactivated 112. 2 Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. Seat not suitable for fitting child seats.
Page 106
CHILD SEATS Installation table The table below summarises the information shown on the following diagram in order to ensure the regulations in 2 force are respected. Front passenger seat (6) Weight of the Rear side seats Rear centre Type of child seat With airbag de...
Page 107
CHILD SEATS B3 = Seat enabling a child seat with "B3" approval to be attached by seat belt: check that it can be fitted. (2) A carrycot can be installed across the vehicle and it will take up at least two seats. Position the child with his or her feet near- est the door. 2 (3) If necessary, position the vehicle seat as far back as possible and raise the seatback (by approximately 25°). In order to in- stall a rear-facing child seat, move the front seat as far forward as possible, then move the front seat back as far as it will go, without allowing it to come into contact with the child seat.
Page 108
CHILD SEATS Attachment using the ISOFIX system 2 Fitting diagram 1 0 6 - G e t t i n g t o k n o w y o u r v e h i c l e...
Page 109
CHILD SEATS RISK OF DEATH OR SERIOUS INJURY: 2 before fitting a rear facing child seat on the front passenger seat, check that the airbag has been deactivated 112. For the front passenger seat, the use of a child seat with a floor support is recommended to avoid triggering the seat belt warning signal.
Page 110
CHILD SEATS Fitting a seat ISOFIX in the rear-left seat means the middle seat cannot be used. The central seat belt will no longer be either accessible or useable. 2 1 0 8 - G e t t i n g t o k n o w y o u r v e h i c l e...
Page 111
CHILD SEATS Installation table The table below summarises the information shown on the following diagram in order to ensure the regulations in 2 force are respected. Front passenger seat (7) Weight of the Size of seat Rear side Rear centre Type of child seat With airbag With airbag...
Page 112
CHILD SEATS IL = Seat allowing a child seat with "Semi-universal or vehicle-specific" approval to be attached using the ISOFIX system on equipped vehicles; check that it can be fitted. i-U = Suitable for "Universal" front-facing and rear-facing i-Size restraint devices. 2 i-UF = Suitable only for "Universal"...
Page 113
CHILD SEATS (7) Deactivate the "Easy Access Seat" function before installing a child seat on the front passenger seat and/or on the rear seats. 2 Risk of injury. G e t t i n g t o k n o w y o u r v e h i c l e - 111...
CHILD SAFETY: DEACTIVATING, ACTIVATING THE FRONT PASSENGER AIRBAG Front passenger airbag deacti- The activation or deacti- vation vation of the front pas- 2 senger airbag must be done while the vehicle is stationary and the ignition is switched off. If it is interfered with when the ve- hicle is being driven, indicator lights will come on. Switch the ignition off then on again to reset the airbag in accor- dance with the lock position.
Page 115
CHILD SAFETY: DEACTIVATING, ACTIVATING THE FRONT PASSENGER AIRBAG bel above) are provided to remind you of these instructions. Activation of the front passen- 2 ger airbag To reactivate the airbag : with the ve hicle stationary, and the ignition switched off, push and turn the lock 1 to the ON position.
Page 116
CHILD SAFETY: DEACTIVATING, ACTIVATING THE FRONT PASSENGER AIRBAG airbag activation/deactivation system is faulty. Allowing any other passenger to sit in 2 that seat is not recommended. Contact your approved Dealer as soon as possible; The passenger airbag may only be activated or deactivated when the vehicle is stationary with the ignition off.
Page 117
2 G e t t i n g t o k n o w y o u r v e h i c l e - 11 5...
DRIVING POSITION Driving position: left-hand drive 2 11 6 - G e t t i n g t o k n o w y o u r v e h i c l e...
Page 119
DRIVING POSITION 15. Centre armrest/storage compart- – lighting dimmer for control instru- The fittings described below DE ment. ments; PEND ON THE VEHICLE VERSION – activation/deactivation of the Lane AND COUNTRY. 16. Charging zone/telephone storage Keep Assist function (lane departure 2 1. Side air vents. 17. USB-C sockets. warning, lane departure prevention, 2.
Page 120
DRIVING POSITION Driver’s position, right-hand dri- 2 11 8 - G e t t i n g t o k n o w y o u r v e h i c l e...
Page 121
DRIVING POSITION – front heated seats; The fittings described below DE – heating or air conditioning; PEND ON THE VEHICLE VERSION 13. Radio remote control. – hazard warning lights; AND COUNTRY. 14. Controls for: – door central locking; 2 1. Side air vents. –...
TRIP COMPUTER Automatic resetting of the journey From the instrument panel A : General information parameters a) trip settings: Resetting occurs automatically when – consumption since the last reset and 2 Trip computer and warning system the maximum value of any of the para- current fuel consumption; meters is exceeded.
Page 123
TRIP COMPUTER Some on-board computer information appears on the 2 navigation system display. The trip settings mileage recorder is reset simultaneously in the on- board computer and the naviga- tion system. G e t t i n g t o k n o w y o u r v e h i c l e - 1 2 1...
Page 124
TRIP COMPUTER Journey settings The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. 2 Examples of selections Interpreting the display selected a) Trip log. Successive display: No stored message – information messages (passenger airbag OFF etc.); – operating fault messages (check the injection system, etc.). b) Current fuel consumption.
Page 125
TRIP COMPUTER Examples of selections Interpreting the display selected Onboard computer with mileagebe 2 fore-service message e) Range before service and oil change. Service in 18,641 miles (30,000 km)/12 Service distance months With the ignition on and the engine not running, access the "Mileage before service"...
Page 126
TRIP COMPUTER Information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. 2 Examples of information messages are given in the following pages. Examples of messages Interpreting the display selected Turn the steering wheel slightly whilst pressing the vehicle start button to unlock the steer- "Turn steering wheel + START"...
Page 127
TRIP COMPUTER Operating fault messages 2 These appear with the warning light to inform you that you should drive very carefully to an approved dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
Page 128
TRIP COMPUTER Warning messages 2 These appear with the warning light and require you to stop immediately, for your own safety, as soon as traf fic conditions allow. Stop your engine and do not restart it. Call an approved Dealer. Some examples of warning messages are given below.
Page 129
TRIP COMPUTER scroll through the various views on the Displays and indicators instrument panel A until you reach the desired view. 2 Instrument panel All of the available views display the following essential information on the instrument panel: – speedometer; –...
Page 130
TRIP COMPUTER Information display Regenerative braking level warning light 9 24 29 Traction battery charging level 10 2 Electric operating mode warning light 11 It is displayed when only the traction battery is powering movement of the vehicle. Information area 12 Speedometer 2 Information on driving aids 3 Estimated range with remaining fuel...
Page 131
TRIP COMPUTER Head-up display 18 on the display. You can also slightly ro- tate the projected image. The visibility of information may be affected by: Adjusting the display brightness 2 The brightness varies automatically – the seat position; according to the light level outside the – the presence of an object vehicle.
Page 132
TRIP COMPUTER Instrument panel in miles Please refer to the multimedia instruc- Vehicle settings personalisation tions for more information. menu 2 To use certain driving aids, it is necessary to change the unit of measurement on the instrument panel in order to obtain the correct information when driving in a country where the speed units differ from those set as default on your vehicle.
Page 133
TRIP COMPUTER Adjusting the settings – a setting for the time the lights are ing to the stored user settings that you switched on (e.g. for the "Follow-me- have previously defined: Select a tab then the function to be home lighting" function). –...
Page 134
TRIP COMPUTER – by changing the user profile; Note: the driving position recall is in- – by pressing the "Recall" button for terrupted if a seat adjustment button is the driver's seat; pressed. 2 – by pressing the buttons 6 for the When the vehicle is started by press- passenger seat. ing and holding the engine start/stop The forward driving position includes button, the driving position is adjusted...
Page 135
TRIP COMPUTER Clock and outdoor temperature If the power supply is cut Clock (battery disconnected, sup- 2 ply wire cut, etc.), the clock must be reset. We recommend that you do not adjust these settings while dri- ving. Exterior temperature indicator As ice formation is relat- ed to climatic exposure, local air humidity and tempera- ture, the external temperature alone is not sufficient to detect...
WARNING LIGHTS The display of information shown If no lights or sounds are below DEPENDS ON THE VEHICLE Warning light apparent, this indicates a EQUIPMENT AND COUNTRY. 2 means you should drive fault in the instrument very carefully to an authorised panel.
Page 137
WARNING LIGHTS and/or messages, and is accompanied Bad weather warning light Oil pressure warning light by a beep. 143 It lights up when the ignition or the en- For your own safety, it requires you to gine is switched on and goes off after a stop immediately, as soon as traffic 2 ...
Page 138
WARNING LIGHTS Dealer as soon as possible. If you fail Coolant temperature warning to follow this recommendation, you risk Tyre under-inflation warning light damaging your vehicle. light This lights up when you switch on the 2 This lights up when the ignition is ignition or when the engine starts.
Page 139
WARNING LIGHTS Lane departure prevention warning light and a beep, this Electric motor fault warning system warning light 196 light means that the electrical circuit is over- charged or discharged 339. When it comes on, this indicates a 2 fault with the electrotechnical system Warning light of the "Active emergency braking"...
Page 140
WARNING LIGHTS On display B 2 Passenger Airbag ON 113 Passenger Airbag OFF 112 Seat belt reminder warning light 80 1 3 8 - G e t t i n g t o k n o w y o u r v e h i c l e...
STEERING Activating/deactivating the function Steering wheel For safety reasons, only With the ignition on, press the button 5 adjust the steering wheel on the multimedia screen 2 . 2 Adjusting the steering wheel height when the vehicle is sta- and depth tionary. Steering wheel heating Deactivating the function –...
Page 142
STEERING Power-assisted steering pending on vehicle, the message will switch off. Never drive with an inadequately Note: the power-assisted steering de- charged battery. 2 pends on the driving mode selected in the "MULTI-SENSE" menu 301. Variable power assisted steering The variable power-assisted steering system is equipped with an electronic Never leave the steering control system which alters the level of...
REAR VIEW Rear view mirrors For safety reasons, carry Objects observed in the out any adjustments rear view mirror glass 2 Exterior rear view mirrors while the vehicle is sta- are actually closer than tionary. they appear. For your safety, take this into account in or- der to correctly assess the dis- Rear view mirrors which tilt in re- tance before any manoeuvre. verse gear On vehicles equipped with this func- –...
Page 144
REAR VIEW When the rear view mirror has been manually deployed or folded back, it is For safety reasons, carry Objects observed in the possible to reset it to a usage position. out any adjustments rear view mirror glass 2 To do this, press the switch 3 . A me- while the vehicle is sta- are actually closer than...
LIGHTING AND SIGNALS Side lights Dipped beam headlights Exterior lighting and signals 2 Daytime running lights Manual operation Turn the ring 3 until the symbol is op- posite the mark 2 . This indicator light on the instrument panel comes on. Before driving at night, check that the electrical equipment is operating correctly and adjust the...
Page 146
LIGHTING AND SIGNALS Main beam headlights cally after several sweeps of the wind- cles that are being followed and those screen wiper blades. coming in the opposite direction. Note: at night, in urban areas with 2 Adaptive front lighting system street lighting, the automatic main beam headlights automatically switch (depending on the vehicle) off.
Page 147
LIGHTING AND SIGNALS Activation/deactivation Note: when you push the stalk 1 , the automatic main beam headlights func- Using a portable naviga- tion system at night in tion is deactivated, the warning 2 the windscreen area be- light disappears from the instrument low the camera may dis- panel and the vehicle activates the turb the operation of the "auto- main beam headlights.
Page 148
LIGHTING AND SIGNALS Adaptive main beam headlights lights will be modified to optimise light- Please refer to the multimedia instruc- ing: tions for further information. – when approaching reflective signs, The main beam headlights come on 2 the lighting power will be locally re- automatically if: duced in order to limit dazzling; – the exterior light level is low; –...
Page 149
LIGHTING AND SIGNALS Activation/deactivation cle in these modes and between these The system may encounter thresholds. difficulties under certain – In Sport mode, the adaptive main 2 conditions, including: beam headlights will switch on when the vehicle speed is over approximate- – extreme weather conditions ly 25 mph (40 km/h) and switch off (rain, snow, fog, etc.);...
Page 150
LIGHTING AND SIGNALS Lights-on reminder buzzer Activating/deactivating the function warning lights on the For activation or deactivation of the ex- If the lights are on after the engine is instrument panel. ternal welcome, refer to the multimedia switched off, a warning beep sounds 2 To increase this duration, you may pull instructions.
Page 151
LIGHTING AND SIGNALS Rear fog light Switching off the lights Headlight beam adjustment To deactivate the function, rotate the rotary switch again so that the mark 4 2 is opposite the symbol 7 . The warning light disappears from the instrument panel. The rear fog lights switch off when the exterior lights are switched off.
Page 152
LIGHTING AND SIGNALS Examples of posi When driving on the left- tions for adjust hand side of the road in a ing the switch A 2 left-hand drive vehicle (or according to the load vice versa), you must adjust your headlights for the length of your Driver alone or stay.
AUDIBLE AND VISUAL SIGNALS will return to its original position and Horn the direction indicator light concerned will flash three times. 2 Hazard warning lights Press the steering wheel boss A to sound the horn. Headlight flasher Press the switch 2 . To flash the headlights, pull the stalk 1 This switch activates all four direction towards you, then release.
WIPER – F : maximum sensitivity. Windscreen wash, wipe The higher the sensitivity, the quicker the wipers will react and the faster the 2 Vehicle fitted with front windscreen wipe. wiper rain sensor When activating automatic wiping or when increasing sensitivity, one sweep of the blades is performed.
Page 155
WIPER Operating faults Precautions wise, there may a risk of damage to In the event of a malfunction of the au- the bonnet or the wipers when they are – In the event of ice, check whether tomatic wiping, the wiper is set to inter- switched on. the blades are stuck to the windscreen mittent wiping. Call an approved deal- 2 ...
Page 156
WIPER With the ignition on, pull the stalk 1 In the event of obstacles on then release. Efficiency of a wiper the windscreen (dirt, snow, blade A longer pull will trigger, in addition to 2 ice etc.), clean the wind- the windscreen washer, two sweeps of Check the condition of the the wipers followed, a few seconds lat- screen (including the central area...
FUEL TANK petrol vapour fumes and to prevent any release when the cap is opened. 2 The valve 2 is built into the filler pipe. Usable capacity of tank: approxi mately 12.1 gallons (55 litres). For details on filling the tank, refer to the information on "Filling with fuel".
Page 158
FUEL TANK pears on the instrument panel and the flap 1 remains locked. Consult an approved dealer. 2 Fuel grade Use a high-grade fuel that complies with the legislation in force in each country and that complies with the specifications given on the label on the flap 1 376.
Page 159
FUEL TANK Keep the nozzle in this position level in the tank, drive the vehicle until tate fuel consumption to enable you to throughout the entire filling operation. the tank has capacity. top up. When the pump cuts out automatically Special case for E-Tech plug-in hy- 2 ...
Page 160
FUEL TANK Persistent smell of fuel If you notice a persistent 2 fuel odour you should: – stop the vehicle when traffic conditions allow it and switch off the ignition; – switch on the hazard warning lights and ask your passengers to leave the vehicle and stay clear of the traffic;...
RUNNING IN For the first 620 miles (1,000 km) do not exceed 80 mph (130 km/h) in the highest gear, or 3,000 to 3,500 rpm. You can only expect top performance from your vehicle after approximately 1,860 miles (3,000 km). 3 ...
STARTING, STOPPING THE ENGINE the Turn steering wheel + START" Starting message will inform you. Depending on the vehicle, you may have a digital key 3 that offers all the functions of the card. However, if a card has been left inside the vehicle and the doors have been locked with a digital key, all of the card's functions will be inhibited.
Page 163
STARTING, STOPPING THE ENGINE Accessories function Operating faults During a system update via (switching on the ignition) In certain cases, the hands-free card the multimedia system it may not work: Once you have gained access to your will not be possible to start vehicle, you may use some of its func- –...
Page 164
STARTING, STOPPING THE ENGINE With the card in the vehicle, press the – the bonnet is open; button 2 : the engine is switched off. – the driver's door is open. Driver's responsibility The READY message disappears from when parking or stop the instrument panel.
GEAR CONTROL One-touch selector Automatic gearbox Electronic selector lever 1 3 To engage position P Move the selector lever 1 one or two notches upwards or downwards to en- gage the desired position (R, N or D) then release the lever and it will return R: reverse gear to the stable position.
Page 166
GEAR CONTROL Driving in automatic mode To select reverse gear With the vehicle at a standstill and the engine or the ignition on, press the With the vehicle stationary, the engine With the vehicle stationary and the en- button 2 to engage the position P. on and your foot on the brake pedal, gine on, move the selector lever 1 two move the selector lever 1 two notches notches upwards to engage R position.
Page 167
GEAR CONTROL mud) make it difficult to stay in auto- notch upwards or downwards then Maintenance period matic mode. On vehicles equipped switch off the engine. Refer to the maintenance document – With the engine off and the ignition with gear shift paddles, it is advisable for your vehicle or consult an Approved to change to manual mode using the on, shift the selector lever 1 one notch Dealer to check whether the automatic...
Page 168
GEAR CONTROL An impact to the under- side of the vehicle while manoeuvring (e.g. strik- ing a post, raised kerb or other street furniture) may result 3 in damage to the vehicle (e.g. de- formation of an axle). To avoid any risk of accident, have your vehicle checked by an approved dealer. In the event of engine failure or an electrical fault (battery fault) affecting operation of the automatic gearbox,...
REGENERATIVE BRAKING SYSTEM Regenerative braking change paddles 1 and 2 3 By releasing the accelerator, the vehi- Regenerative braking levels cle uses regenerative braking to slow The 3 warning light informs you of the down the vehicle. regenerative braking level: Some of this energy is converted to –...
Page 170
REGENERATIVE BRAKING SYSTEM However, the pedal may appear more depressed and feel firmer. This is nor- mal. To limit this effect, use the regenerative braking levels A and B . 3 1 6 8 - D r i v i n g...
SPECIAL FEATURES OF PETROL ENGINES having identified and corrected the After between approximately 5 and 20 The following operating conditions: starting fault. minutes, the warning light should go – driving for long periods when the low out. If the fault cannot be identified, do not fuel level warning light is lit;...
Page 172
SPECIAL FEATURES OF PETROL ENGINES The warning light for your own safety, it requires you to stop immediately as soon as traf- 3 fic conditions allow. Switch off the engine and do not restart it. Call an approved Dealer. 1 7 0 - D r i v i n g...
PARKING BRAKE after the electronic parking brake has Electronic parking brake – when the P position is engaged. been applied and the warning In all other instances, e.g. if the en light goes out when the vehicle is Assisted operation gine stalls, the electronic parking locked.
Page 174
PARKING BRAKE Manually applying the electronic parking brake The electronic parking The electronic parking brake can be used to im- brake can be used to im- mobilise the vehicle. Be- mobilise the vehicle. Be- fore leaving the vehicle, fore leaving the vehicle, check that the electronic parking check that the electronic parking 3 brake is fully applied. Application brake is fully applied.
Page 175
PARKING BRAKE Manually releasing the electronic Brief stop – engage P position: the drive wheels parking brake are mechanically locked by the drive- shaft; – stop the engine by pressing the en- gine Start/Stop button 1 ; – unfasten the driver's seat belt; 3 – open the driver's door; – manually release the electronic park- ing brake (please see the paragraph on "Manually releasing the electronic parking brake");...
Page 176
PARKING BRAKE Versions with an automatic gear- "Autohold" function Never leave your vehicle Vehicle stopped (e.g. at a red light, an without re-engaging P For safety reasons, automatic release intersection, a traffic jam, etc.), the position and switching is deactivated when the driver’s door is function ensures braking force even off the engine.
Page 177
PARKING BRAKE Deactivation The maintained braking force is con- The electronic parking Press the switch 1 . If your vehicle is firmed by the warning light on brake can be used to im- maintained by braking force you can the instrument panel. mobilise the vehicle. Be- also press the brake pedal. fore leaving the vehicle, The warning light on the switch 1 dis- Conditions for interrupting the check that the electronic parking...
ENVIRONMENT must be handed to a legal entity that many parts made from recycled plas- Your vehicle has been designed with complies with environmental stan- tics or renewable materials. respect for the environment in mind dards. for its entire service life: during its pro- – Worn parts replaced in the course of duction, usage and at the end of its routine vehicle maintenance (vehicle service life.
MAINTENANCE AND ANTIPOLLUTION ADVICE longer complies with antipollution regu- mosphere or mechanical damage may Your vehicle complies with criteria for lations. occur. recycling and recovering vehicles at the end of their service life, which en- Have your vehicle adjusted and This indicator light on the instru- tered into force in 2015. checked by an approved dealer, in ac- ment panel indicates possible faults in cordance with the instructions given in Some of the parts on your vehicle the system.
DRIVING ADVICE, ECO-DRIVING On the instrument panel A Driving style indicator 2 Eco-driving Fuel consumption is accredited in ac- cordance with a standard regulatory method. Identical for all manufacturers, this enables vehicles to be compared 3 with one another. Consumption in real time depends on vehicle usage conditions, equipment fitted and the user’s driving style. To ...
Page 181
DRIVING ADVICE, ECO-DRIVING If your driving behaviour is deemed un- ving and its effect on your fuel con- – using the steering wheel control 5 . economic (small orange leaf), you may sumption. be provided with advice. Please refer to the multimedia instruc- If you regularly monitor this indicator tions for further information. you will be able to reduce your ECO mode vehicle's fuel consumption.
Page 182
DRIVING ADVICE, ECO-DRIVING Power meter In all-electric or hybrid mode, the trac- – High speeds significantly affect the tion battery and/or the combustion en- vehicle's fuel consumption. gine supply the energy required to Examples (at a steady speed): move the vehicle. – reducing the speed from approxi- mately 80 mph (130 km/h) to 68 mph Navigation system (110 km/h) saves up to around 20% of 3...
Page 183
DRIVING ADVICE, ECO-DRIVING It is normal to notice an increase in the vehicle's fuel consumption when using the heating (particularly when the out- side temperature drops below zero) or air conditioning. 3 Driver obstruction On the driver's side, only use mats that are suit- able for the vehicle, at- tach using the pre-fitted compo- nents, and check the fittings regu- larly. Do not lay one mat on top of another.
Page 184
DRIVING ADVICE, ECO-DRIVING Advice for reducing consumption and helping to preserve the environ ment: If the vehicle has been parked in the sun, open the doors for a few mo- ments to let the hot air escape before 3 starting the engine. – Do not leave an empty roof rack fit- ted to the vehicle. –...
TYRE PRESSURE LOSS WARNING The system can be identified by the 1 label in the vehicle. This function is an addi- tional driving aid. Operating principle The function does not take the place of the dri- ver. It cannot, therefore, under 3 any circumstances replace the vigilance or the responsibility of the driver. Check the tyre pres- sures, including the emergency spare wheel, once a month.
Page 186
TYRE PRESSURE LOSS WARNING – significant change in load or distribu- – after changing wheels around. tion of load on one side of the vehicle; For your safety, the Tyre pressures must correspond to the – sporty driving with strong accelera- current usage of the vehicle (empty, tion; warning light carrying a load, motorway driving, –...
Page 187
TYRE PRESSURE LOSS WARNING Emergency spare wheel The table lists the warning messages which appear on the instrument panel If fitted on the vehicle, readjust the tyre 4 when the system detects a tyre pressure and launch the resetting of pressure fault.
Page 188
TYRE PRESSURE LOSS WARNING Fault message table The information on the instrument panel signals any potential tyre pressure faults (e.g. deflated or punctured tyre). Indicator lights Messages Readings 3 This indicates that tyre under-inflation or punc- ture has been detected. Check and adjust the Inflate tyres and init. pressure of the four tyres when cold and reset comes on the system.
DRIVER CORRECTION DEVICES AND AIDS You will feel a pulsation through the Depending on the vehicle, they may in- These functions are an brake pedal each time the system is clude: activated. The front passengerABS additional aid in the – the anti-lock braking system does not in any way improve the event of critical driving (ABS);...
Page 190
DRIVER CORRECTION DEVICES AND AIDS panel, accompanied by the "Braking corrects the trajectory if necessary by In some situations (driving on very soft system fault" message to indicate a controlling the braking of certain ground such as snow or mud, or dri- ving with snow chains fitted), the sys- fault in the braking system. wheels and/or engine power.
Page 191
DRIVER CORRECTION DEVICES AND AIDS In some situations (driving on very soft Depending on the vehicle, these may ground such as snow or mud, or dri- flash in the event of sudden decelera- These functions are an ving with snow chains fitted), the sys- tion. additional aid in the tem may reduce the engine power to Braking anticipation event of critical driving limit wheelspin.
Page 192
DRIVER CORRECTION DEVICES AND AIDS – the wiring must be authorised by an vehicle from rolling backwards by auto- approved dealer; matically applying the brakes when the The hill start assistance – the towbar must be connected to the driver lifts his/her foot off the brake system cannot complete- vehicle.
Page 193
DRIVER CORRECTION DEVICES AND AIDS Starting the system Hill descent control operates between approximately 4 and 19 mph (6 and 30 With the vehicle moving downhill, as km/h) in forward gear and at approxi- soon as sufficient gradient is detected, mately 4 mph (6 km/h) in reverse gear. Note: if the vehicle speed is above 37 warning light turns to green.
Page 194
DRIVER CORRECTION DEVICES AND AIDS Rear wheel steering The hill descent control system may deactivate itself temporarily if there is a risk of the braking system temperature increasing 3 (the warning light goes out). If necessary, use the brake pedal to stop the vehicle.
Page 195
DRIVER CORRECTION DEVICES AND AIDS Operating principle – Comfort; – If the warning light is dis- – Dynamic; When the airbag system detects a col- played on the instrument panel, ac- – Sport. lision, the pretensioners or airbags are companied by the "Steering fault" mes- triggered 85 and the "Multi-collision sage, this indicates a system fault. braking" function activates the Elec- tronic Stability Program (ESC) to brake 3 ...
Page 196
DRIVER CORRECTION DEVICES AND AIDS Regenerative braking system The warning light When braking, the regenerative brak- ing system can convert the energy pro- for your own duced by the vehicle deceleration into safety, it requires you to electric energy. stop immediately as soon as traf- 3 This will recharge the traction battery fic conditions allow. Switch off the and extend the vehicle range.
ADDITIONAL DRIVING AID FUNCTIONS – overspeed sound alert 229; My Safety – lane departure prevention 196; Depending on the length of – driver vigilance warning 227; time following the last time The "My Safety" function can be used – emergency lane departure preven- the engine was stopped, to deactivate or activate a set of driver tion 203.
Page 198
ADDITIONAL DRIVING AID FUNCTIONS Activation/deactivation Please refer to the multimedia instruc- tions for more information. – performs corrective action on the From the multimedia screen 2 steering system. Lane departure prevention You can retake control of 3 the vehicle at any time by operating the steering wheel.
Page 199
ADDITIONAL DRIVING AID FUNCTIONS Using the switch "My Safety" 3 Operation – crosses a continuous line without ac- tivating the indicator lights; – crosses a broken line without acti- vating the direction indicators, if the "operation on broken line" setting is se- lected. 3 In these cases: – the function triggers an action on the vehicle's steering system to correct the vehicle trajectory;...
Page 200
ADDITIONAL DRIVING AID FUNCTIONS – the "Lane Centring" function is put – the warning light and the indi- You can interrupt the trajec- on standby while the "Lane Departure cator 4 on the side of the breached Prevention" function is ready or in op- tory correction at any time line turns to red on the instrument pan- by moving the steering eration: the warning light is dis- wheel.
Page 201
ADDITIONAL DRIVING AID FUNCTIONS – operation of the anti-lock braking When the function is deactivated, the – setting not selected: the function system; can warn the driver by means of a warning light is displayed in yel- – the active emergency braking sys- vibration at the steering wheel with- tem is triggered; out correcting the vehicle trajectory.
Page 202
ADDITIONAL DRIVING AID FUNCTIONS Consult an approved dealer. 3 2 0 0 - D r i v i n g...
Page 203
ADDITIONAL DRIVING AID FUNCTIONS Warnings This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. 3 ...
Page 204
ADDITIONAL DRIVING AID FUNCTIONS – the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an approved dealer); – the vehicle is towing a trailer or a caravan; – the vehicle is entering an area with several surface markings (an area with road works etc.). 3 2 0 2 - D r i v i n g...
Page 205
ADDITIONAL DRIVING AID FUNCTIONS Using information from the radar 2 and Emergency lane departure pre- the camera 1 , the function triggers This system provides an corrective action on the vehicle steer- vention additional driving aid. ing system in the event of a risk of col- This system is not, under lision with a vehicle coming from the any circumstances, in- opposite direction in the adjacent lane, tended to replace the due care...
Page 206
ADDITIONAL DRIVING AID FUNCTIONS Activating/deactivating the function Detection of an oncoming vehicle From the A "My Safety" switch 3 Please refer to the multimedia instruc- tions for more information. Press switch A twice if the function has been deactivated via the Custom mode of the "My Safety" function 195.
Page 207
ADDITIONAL DRIVING AID FUNCTIONS lision with a vehicle coming from the opposite direction in an adjacent lane This function is an addi- and within the detection zone C , with- tional driving aid. out the direction indicator having been This function is not un- activated, the system: der any circumstances –...
Page 208
ADDITIONAL DRIVING AID FUNCTIONS 3 While driving at a speed over 40 mph (65 km/h), when approaching a line (continuous or broken) and there is a risk of collision with a vehicle located in the blind spot D and it is moving in the same direction as your vehicle or with a vehicle that is rapidly approach- ing from behind in an adjacent lane...
Page 209
ADDITIONAL DRIVING AID FUNCTIONS – the camera does not simultaneously – The anti-lock braking system is mal- detect the two boundaries of the lane functioning; – triggers corrective action on the – A towbar is electrically connected to in which your vehicle is moving; steering system. –...
Page 210
ADDITIONAL DRIVING AID FUNCTIONS Warnings This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. 3 System servicing/repairs –...
Page 211
ADDITIONAL DRIVING AID FUNCTIONS – the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an approved dealer); – the vehicle is towing a trailer or a caravan; – the vehicle is being towed (breakdowns); –...
Page 212
ADDITIONAL DRIVING AID FUNCTIONS Blind spot warning The function does not notify the driver if the other vehi- cles are not moving. 3 This function is an addi- tional driving aid. This function is not under any circumstances intended to replace the due care and atten- tion of the driver, who should at all times be in control of the vehicle. Using information from the sensors in- stalled on each side of the rear Special feature...
Page 213
ADDITIONAL DRIVING AID FUNCTIONS Ensure that zone C around the radars – if you overtake another vehicle, the warning area and/or a vehicle is rapid- warning light 2 will only come on, if on each side of the rear bumper are ly approaching from the rear on the not obstructed (by dirt, mud, snow, that vehicle remains for a long enough side towards which you will turn the...
Page 214
ADDITIONAL DRIVING AID FUNCTIONS Due to the presence of sen- sors behind the bumper, it is advisable to entrust any operation on the bumper (repair, replacement, paintwork, etc.) to a 3 qualified professional. 2 1 2 - D r i v i n g...
Page 215
ADDITIONAL DRIVING AID FUNCTIONS Warnings – The system’s detection range operates according to a standard lane width. If driving on a narrow lane, the sys- tem may warn you when a vehicle is detected further away than the nearest lane. 3 – The system’s detection range operates according to a standard lane width. If you are driving in wide traffic lanes, the system might not be able to detect a vehicle in the blind spot. –...
Page 216
ADDITIONAL DRIVING AID FUNCTIONS This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The driver should always adapt their speed to the traffic conditions, regardless of the system indications.
Page 217
ADDITIONAL DRIVING AID FUNCTIONS Limitation of the system operation – The radar area should be kept clean and free of any modifications in order to ensure the proper operation of the system. – Small objects moving close to the vehicle (motorcycles, bicycles, pedestrians, etc.) may not be recognised by the sys- 3 tem. – When turning into a bend, the radars may temporarily cease to detect vehicles in adjacent lanes. –...
Page 218
ADDITIONAL DRIVING AID FUNCTIONS Location of the radar 2 Activation/deactivation from the Safe distance alert multimedia screen 3 Ensure that the radar area is not ob- structed (by dirt, mud, snow, a badly fitted front number plate etc.), impact- ed, modified (including painting) or hid- den by any accessory fitted on the 3 front of the vehicle (on the grille or logo etc.).
Page 219
ADDITIONAL DRIVING AID FUNCTIONS Operation (very insufficient distance between the two vehicles). If the interval between the two vehicles is less than around 0.5 seconds, notifi- cation 8 , display D , will remain lit red on the instrument panel. 3 Under certain conditions, the time in- terval may not be displayed: –...
Page 220
ADDITIONAL DRIVING AID FUNCTIONS Warnings The measurement is displayed for information: the system does not carry out any action on the vehicle. This function is not designed for use in urban conditions or for a dynamic driving style (sudden cornering, acceler- 3 ation, braking, etc.), but rather for stable driving conditions. The function does not interact with the braking system. The radar and camera zones must be kept clean and free of any tampering in order to ensure the proper operation of the system.
Page 221
ADDITIONAL DRIVING AID FUNCTIONS This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. System servicing/repairs –...
Page 222
ADDITIONAL DRIVING AID FUNCTIONS – and stationary vehicles; Active emergency braking This system can apply maximum braking to the – surrounding pedestrians and cy- vehicle until it is completely clists. stationary if necessary. The system informs the driver if there For safety reasons, always wear 3 is a risk of head-on collision to enable your seat belt when travelling in...
Page 223
ADDITIONAL DRIVING AID FUNCTIONS Note: if the driver presses the brake pedal and the system still detects a In the event of an emer- risk of collision, the braking force may gency manoeuvre, you can be increased if it is not sufficient to pre- stop the braking at any mo- vent the collision. ment by: – can trigger braking: if the driver –...
Page 224
ADDITIONAL DRIVING AID FUNCTIONS Activation/deactivation Stationary vehicles are detected by the system when: – your vehicle is travelling at a speed Depending on the vehicle, between approximately 5 mph (8 km/h) according to the length of and 50 mph (80 km/h). time following the last time 3 Detection of pedestrians and cy-...
Page 225
ADDITIONAL DRIVING AID FUNCTIONS The possible causes are: – the system is temporarily blinded (glare from the sun, dipped beam headlights, bad weather conditions etc.). The system will be operational again when visibility conditions are 3 better; – the system is temporarily interrupted (e.g.
Page 226
ADDITIONAL DRIVING AID FUNCTIONS Warnings This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The triggering of this function 3 may be delayed or prevented when the system detects clear signs of control of the vehicle by the driver (action on the steering wheel, pedals etc.).
Page 227
ADDITIONAL DRIVING AID FUNCTIONS System disturbance Some conditions can disturb or damage the system's operation, such as: – a complex environment (metal bridge, tunnel, etc.); – poor weather conditions (snow, hail, black ice, etc.); – poor visibility (night, fog, etc.); 3 ...
Page 228
ADDITIONAL DRIVING AID FUNCTIONS Deactivating the function You must deactivate the function if: – the camera area has been damaged (e.g. on the inside or outside of the windscreen); – the front of the vehicle was damaged (impact, scratch on the radar, etc.); 3 –...
Page 229
ADDITIONAL DRIVING AID FUNCTIONS Operation – a few minutes have elapsed since Driver vigilance warning the vehicle last stopped; – the vehicle speed is greater than ap- The driver vigilance warning is a func- proximately 43 mph (70 km/h). tion that analyses the behaviour of the If there is a risk of fatigue or impaired driver (driving style, vehicle steering, attention, the "Vigilance alert Have a etc.) and alerts them if there is a risk of...
Page 230
ADDITIONAL DRIVING AID FUNCTIONS Activation/deactivation Activating and deactivating alerts using the "My Safety" button 3 Depending on the vehicle, alerts are automatically de- For safety reasons, carry activated when the "Lane out any adjustments Centring" function is activated. To while the vehicle is sta- re-activate the warnings, the 3 tionary.
Page 231
ADDITIONAL DRIVING AID FUNCTIONS Activating and deactivating the – winding roads; It mainly uses information taken from alerts from the multimedia screen the camera 1 attached to the wind- – trailer traction. screen behind the rear view mirror. De- Operating faults pending on the country, the system al- so uses information from a map sub- If the system detects a fault, the scription to interpret certain signs "Check Fatigue Warning System" mes- 3 ...
Page 232
ADDITIONAL DRIVING AID FUNCTIONS Operation to the unit used by the vehicle’s instru- It remains illuminated on the instru- ment panel. ment panel as long as the vehicle – for countries where the speed limit is speed is exceeding the speed limit. reduced during rainy weather on some types of roads, the system may alter Map subscription the detected speed limit after a few 3...
Page 233
ADDITIONAL DRIVING AID FUNCTIONS The sound alert can be deactivated or Select "ON" or "OFF". Depending on the vehicle, activated using "Custom" mode in the "My Safety" function 195. Variation of the limited speed or depending on the length of cruising speed time following the last time If the sound alert has previously been...
Page 234
ADDITIONAL DRIVING AID FUNCTIONS – the windscreen is not clean; This system consists of the "Adaptive – the camera is blinded by the sun; This function is an addi- cruise control Stop and Go" func tion 252 and the "Lane Centring" – there is insufficient visibility (fog, tional driving aid.
Page 235
ADDITIONAL DRIVING AID FUNCTIONS brake your vehicle to a complete stop take immediate action on the steering before setting off again. The Stop and Go adaptive wheel. cruise control does not trig- Additional information ger an emergency stop and Important: you should its braking capability is limited. Depending on the vehicle, the "Active keep your feet near the driver assist"...
Page 236
ADDITIONAL DRIVING AID FUNCTIONS Location of components 3 2 3 4 - D r i v i n g...
Page 237
ADDITIONAL DRIVING AID FUNCTIONS conditions. 1 Camera The radar and camera 4 Capacitive sensor Detects markings on the ground and zones must be kept Depending on the vehicle, it detects the position of vehicles on the various clean and free of any hands on the steering wheel.
Page 238
ADDITIONAL DRIVING AID FUNCTIONS Controls 3 2 3 6 - D r i v i n g...
Page 239
ADDITIONAL DRIVING AID FUNCTIONS 9. Switch for selecting/deselecting the driving aids, depending on the vehicle: – the Active driver assist; – Adaptive Cruise Control; – speed limiter; – OFF. 3 10. Safe distance settings 11. Puts the function on standby and stores the limited speed (0).
Page 240
ADDITIONAL DRIVING AID FUNCTIONS Activating/deactivating the "Active The green warning light 22 Displays on the instrument panel driver assist" function the left-hand and right-hand line indi- 17. Stop and Go adaptive cruise con- cators 21 are displayed on the instru- Activating the function ment panel to confirm that the function trol function warning light is in operation and directing your vehi- 3 cle towards the centre of the lane.
Page 241
ADDITIONAL DRIVING AID FUNCTIONS stop exerting effort to turn the steering – the system is temporarily disrupted wheel. The lines 21 indicate the offset (for example: camera obscured by dirt, applied. To return to the centre of the mud, snow, condensation, etc.). lane, turn the steering wheel slightly in Certain actions carried out by the dri- the opposite direction, then stop trying...
Page 242
ADDITIONAL DRIVING AID FUNCTIONS message appears on the instrument You can affect the vehicle In the first two alert levels, panel and the warning light 24 trajectory at any point by when the system again de- appears in red, accompanied by a turning the steering wheel. tects the presence of the gradually increasing sound signal;...
Page 243
ADDITIONAL DRIVING AID FUNCTIONS In the case of a sharp bend concerned appear in red on the instru- Consult an approved dealer. ment panel. If the vehicle crosses a line com pletely and moves out of its lane or if the bend is too sharp, the "Lane Centring"...
Page 244
ADDITIONAL DRIVING AID FUNCTIONS Warning The "Active driver assist" is an additional driving aid. it can under no circumstances replace the driver's responsi- bility to respect speed limits and safe distances and to be vigilant. 3 The driver must always be in control of the vehicle. The driver must always adapt their trajectory and speed according to the surroundings and driving conditions, re- gardless of system indications. Except for lines delimiting lanes and the speed limit signs within the limits of the system's detection capacity, the road sign information (other traffic signs, traffic lights, pedestrian crossings, etc.) are not recognised by the system. These do not trig- ger any alert or reaction by the system.
Page 245
ADDITIONAL DRIVING AID FUNCTIONS Deactivating the system You must deactivate the system if: – the vehicle is travelling on a winding road; – the vehicle is being towed (breakdowns); – the vehicle is towing a trailer or a caravan; 3 –...
Page 246
ADDITIONAL DRIVING AID FUNCTIONS Some conditions can disrupt or damage the system operation, for example: – obstruction of the windscreen or the radar area (by dirt, ice, snow, condensation etc.) Frequently check the cleanliness and condition of the windscreen, front wiper blades and front bumper; –...
Page 247
ADDITIONAL DRIVING AID FUNCTIONS Operation When in reverse gear and moving at Active emergency braking in re- between approximately 2 mph and 6 mph (3 km/h and 10 km/h), if there is a verse gear risk of collision with a fixed obstacle, the system automatically brakes the 3 ...
Page 248
ADDITIONAL DRIVING AID FUNCTIONS ing aids". Select "Active emergency Clean the ultrasonic sensors. If there is An impact to the under- braking in reverse gear". still a problem, contact an approved dealer. side of the vehicle while If the function is deactivated, the warn- manoeuvring (e.g. strik- If the vehicle is fitted with a towbar ing light 3 is displayed on the recognised by the system and a trailer...
Page 249
ADDITIONAL DRIVING AID FUNCTIONS Warnings Active emergency braking in reverse gear This function is an additional driving aid. This function cannot, under any circumstances, replace the vigilance and 3 responsibility of the driver. Some climatic and environmental conditions can disrupt or damage the system. As a consequence, the driver should always be ready for sudden incidents while driving: always ensure that there are no small, narrow moving obstacles (such as a child, animal, pushchair, bicycle, stone, post, etc.) in the blind spot when manoeuvring.
SPEED LIMITER 1. Switch for selecting/deselecting the When the "OFF" mode is activated be- The speed limiter function controls the driving aids, depending on the vehicle: fore the ignition is switched off, the engine and braking system to help you "Speed limiter" function will be activat- not to exceed a driving speed that you –...
Page 251
SPEED LIMITER Switching on The minimum stored speed is 19 mph (30 km/h). Varying the limit speed 3 The 6 warning light appears in grey. The "Speed limiter ready: SET to acti- Press switch 1 as many times as nec- vate" message is displayed on the in- essary to select the speed limiter A . strument panel accompanied by dash- es to indicate that the speed limiter You can change the limit speed by re- function is activated and waiting for a...
Page 252
SPEED LIMITER tivated. To manage your subscription, The speed limiter function is suspend- ed when you press switch 2 (0). see the multimedia instructions.) You must keep your feet near the pedals to Using the camera, the "Road sign de- The limit speed is stored and displayed tection" function 229 and the map be ready to react in an in grey on the instrument panel.
Page 253
SPEED LIMITER Switching off the function The speed limiter function is interrupt- ed when you press the 1 switch to de- select the limiter. In this case, the speed is no longer stored. The 6 warning light disappears from the instrument panel to confirm that 3 the function has stopped. The minimum stored speed is 19 mph (30 km/h).
ADAPTIVE CRUISE CONTROL The Stop and Go adaptive cruise con- Based on information from a radar or trol function can be activated while the The regenerative braking camera, the Stop and Go adaptive vehicle is travelling at a speed up to system and the paddles are cruise control function gives you the 112 mph (180 km/h), depending on option of maintaining a selected...
Page 255
ADAPTIVE CRUISE CONTROL Location of the camera 1 Controls This function is an addi- tional driving aid. It can under no circum- stances replace the driver's responsibility to respect 3 speed limits and safe distances or to be vigilant. The driver must always be in con- trol of the vehicle. The driver must always adapt their speed according to the sur- roundings and traffic conditions.
Page 256
ADAPTIVE CRUISE CONTROL – Downwards: activates, decreases Displays Switching on cruising speed or stores the current speed (SET/-). 7. Pop-up button (depending on the vehicle): adapts the speed setpoint to 3 229 detected speed limits 8. Adjusting the following distance. Depending on the vehicle, you can link the cruise con- trol function to the "Road...
Page 257
ADAPTIVE CRUISE CONTROL The "Adaptive Cruise Ctl unavailable" Activating cruise control with From the multimedia screen, in the message is displayed on the instru- "Vehicle" World, select "Driving assis- speed limit sign recognition ment panel. tance". Then, on the "Speed manage- (display A ) ment" menu, activate the "Adjust Activating cruise control speed limitations"...
Page 258
ADAPTIVE CRUISE CONTROL justment of the vehicle speed until the – in some cases (if there is a signifi- The detected speed 15 is taken into next sign is identified 15 . cant difference between the vehicle account by the system. The vehicle speed adjusts gradually, until it be- speed and limited speed), the system Activation/deactivation may request that you validate the comes the cruising speed 10 , without...
Page 259
ADAPTIVE CRUISE CONTROL Activation/deactivation Controlling cruising speed From the multimedia screen, in the You can resume control of the vehicle "Vehicle" World, select "Driving assis- speed at any time by: tance". Then, from the "Comfort" – putting the function on standby: menu, select "Road layout adaptive –...
Page 260
ADAPTIVE CRUISE CONTROL er the outline, the closer the vehicle in The horizontal distance gauge on the If it is exceeded, the cruising speed 10 front. instrument panel indicates the various appears in yellow. available safe distances: If the driver presses the accelerator Setting the cruising speed –...
Page 261
ADAPTIVE CRUISE CONTROL without any action required from the The function is deactivated by the sys- driver. tem if: Stopping the Stop and Go adaptive cruise con- Note: the driver should always be – you put the gear control in position ready for sudden incidents while dri- P, R or N ; trol function or putting it ving and remains responsible for con- –...
Page 262
ADAPTIVE CRUISE CONTROL hicle is moving that is taken into ac- – the red alert J accompanied by Temporary unavailability (radar) count. the "Brake" message if the situation re- quires immediate action by the driver. "Take control of the vehicle" In all situations, react accordingly warnings and perform the appropriate ma noeuvres. 3 Switching off the function The radar is able to detect vehicles in front of your vehicle. The system can-...
Page 263
ADAPTIVE CRUISE CONTROL any accessory fitted on the front of the strument panel and the Stop and Go Limitations of system operation vehicle (on the grille), or hidden by any adaptive cruise control function is in- accessory fitted on the front of the ve- terrupted. Vehicle detection hicle (on the grille or logo, etc.). If an operating fault is detected on one Conditions in certain geographical ar- or more of the system components,...
Page 264
ADAPTIVE CRUISE CONTROL Detection during cornering Detection of vehicles in adjacent lanes 3 The system cannot detect: – vehicles arriving at intersections: slip When entering a corner or bend, the road (e.g. M ), etc.; radar and/or camera may be temporar- The system may detect vehicles dri- – vehicles driving on the wrong side of ily unable to detect the vehicle in front ving on an adjacent lane when: the road or reversing towards you.
Page 265
ADAPTIVE CRUISE CONTROL The system will not detect vehicles hidden due to variations in ground re- lief or those located outside of the camera and radar detection areas when driving uphill or downhill. Vehicles outside the camera and 3 radar detection areas. The system will react late or not at all if the detected vehicles are outside the camera and radar detection areas, particularly in the following cases:...
Page 266
ADAPTIVE CRUISE CONTROL – stationary vehicles 21 , when you – pedestrians, bikes, scooters, etc.; change lane (e.g. T ). – animals; – fixed obstacles (toll barriers, walls, etc.) (e.g. U ). Always be ready to re These are not taken into account by spond in all circum...
Page 267
ADAPTIVE CRUISE CONTROL Warnings This function is an additional driving aid. It can under no circumstances replace the driver's responsibility to re- spect speed limits and safe distances or to be vigilant. 3 The driver must always be in control of the vehicle. Apart from the speed limit signs and road map information from the mapping (vehicles fitted with the "Road sign detection" function and a subscription), other traffic information (traffic lights, pedestrian crossings, etc.) is not taken into ac- count by the system.
Page 268
ADAPTIVE CRUISE CONTROL Deactivating the function You must deactivate the function if: – the vehicle is being towed (breakdowns); – the vehicle is towing a trailer or a caravan; 3 – the vehicle is being driven in a tunnel or close to a metallic structure; –...
Page 269
ADAPTIVE CRUISE CONTROL In the event of system disturbance Some conditions can disturb or damage the system's operation, such as: – the windscreen or bumper is obscured in the radar area (by dirt, ice, snow, condensation, number plate, etc.); – a complex environment (tunnel, etc.); –...
PARKING AIDS The function does not take into ac- Parking distance control count towing or carrying systems that An impact to the under- are not recognised by the system. side of the vehicle while Operating principle manoeuvring (e.g. strik- ing a post, raised kerb or This function is an addi- other street furniture) may result 3 tional driving aid.
Page 271
PARKING AIDS Operation In the event of a change in trajectory during a manoeu- vre, the risk of collision with an obstacle may be signalled late. 3 Special case of obstacles detected on the side The system is able to detect most ob- stacles located near the rear and, de- The display 2 shows the vehicle sur- pending on the vehicle, near the front roundings and emits beeps.
Page 272
PARKING AIDS gets nearer. The area where the obsta- proximately five seconds and an ob- cle 3 has been detected is displayed stacle is detected (such as when in a (display D ). traffic jam, etc.); – if there is no risk of collision, no – when you are in N or P position; beep will sound when approaching the –...
Page 273
PARKING AIDS If it the fault persists, consult an ap- Each time the vehicle is proved dealer. started, the function re- sumes the activation status saved the last time the engine was stopped. 3 Special cases You can manually deactivate sound alerts or, depending on the vehicle, the detection zone concerned in the event that: –...
Page 274
PARKING AIDS Advice When the vehicle is travelling at a speed below approximately 6 mph (10 km/h), some noises (motorcycle, lorry, pneumatic drill, etc.) may trigger the Park Assist system audible warnings. 3 2 7 2 - D r i v i n g...
Page 275
PARKING AIDS System servicing/repairs – In the event of an impact, the alignment of the ultrasonic sensors may be altered and its operation may conse- quently be affected. Deactivate the function and consult an authorised dealer. – Any work in the area where the ultrasonic sensors are located (repairs, replacements etc.) must be carried out by a quali- 3 fied professional. Only an authorised dealer is qualified to service the system. System disturbance Some conditions can disrupt or damage the system operation, for example: –...
Page 276
PARKING AIDS Reversing camera Operation 3 Fixed guide lines 3 Trailer guide line 5 The fixed gauge includes coloured This is shown in blue on the multime- markers A , B and C indicating the dia screen 2 . This indicates the trajec- distance behind the vehicle: tory of the trailer towbar according to the steering wheel position.
Page 277
PARKING AIDS Settings If an obstacle is detected behind the vehicle, the function "Zoom auto" This function is an addi- switches the current display to a top tional aid. It cannot, rear view. therefore, under any cir- To activate/deactivate the "Zoom auto" cumstances replace the function, refer to the multimedia in- vigilance or the responsibility of 3 structions. the driver. The driver should always be ready for sudden incidents while The screen shows a re-...
Page 278
PARKING AIDS Difference between the estimated distance and actual distance 3 Driving or reversing towards a pro Driving or reversing towards a steep downhill slope truding object The fixed guidelines 3 show the dis- Position H seems further than position Driving or reversing towards a steep J on the screen.
Page 279
PARKING AIDS Switching on Special features Hands-free parking 3 With the vehicle stationary or driving at Ensure that the ultrasonic detectors in- As indicated by the arrows 1 , the ultra- less than approximately 19 mph (30 dicated by the arrows 1 are not ob- sonic detectors installed in the vehicle km/h), there are several ways to ac- scured (by dirt, mud, snow, a badly fit- bumpers help to find accessible park-...
Page 280
PARKING AIDS Choice of manoeuvre In other cases, the default manoeuvre Parking can be set from the multimedia screen As long as the vehicle speed is less than 19 mph (30 km/h), the system Please refer to the multimedia instruc- looks for available parking spaces on tions for further information.
Page 281
PARKING AIDS Your speed should not exceed around The warning light warning light This function is an addi- 4 mph (7 km/h). disappears from the instrument panel tional driving aid. Once the vehicle is in a position to exit accompanied by a beep to inform you Therefore, it can under the parking space, the warning light that the manoeuvre has been sus-...
Page 282
PARKING AIDS Cancelling the manoeuvre Operating faults The manoeuvre is cancelled in the fol- When the function detects an operat- lowing cases: ing fault, the following messages are displayed on the instrument panel: – you take control of the wheel; – the vehicle speed has exceeded 4 – "Check Park Assist", accompanied 3 mph (7 km/h);...
Page 283
PARKING AIDS Warnings This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. Make sure that the manoeuvre 3 ...
Page 284
PARKING AIDS Using information from cameras 1 , 2 – front view (using camera 1 ): stan- 360° camera and 3 located in the front bumper, dard front view and panoramic front door mirrors and on the tailgate, as view; well as ultrasonic detectors 4 located –...
Page 285
PARKING AIDS Front camera 1 Rear camera 3 This function is an addi- tional aid. It cannot, therefore, under any cir- cumstances replace the vigilance or the responsibility of 3 the driver. The driver should always be ready for sudden incidents while driving: always ensure that there are no small, narrow moving ob- stacles (such as a child, animal, pushchair, bicycle, stone, post,...
Page 286
PARKING AIDS This is shown in blue on the multime- dia screen 5 . It indicates the vehicle For the rear views, the mul- trajectory according to the position of timedia screen 5 shows a the steering wheel in the front and the reverse image of the rear rear view. view as in a rear view mirror. Trailer guide line 8 3 This is shown in blue on the multime-...
Page 287
PARKING AIDS bird's eye view to the front side view. In the combined repre- Please refer to the multimedia instruc- In "bird's eye view" mode, tions for further information. sentation from the cam- the objects displayed on eras: the multimedia screen are Bird's eye view actually further away than they – raised objects (pavement, vehi- seem.
Page 288
PARKING AIDS Front panoramic view or rear 3D view Trailer view panoramic view 3 On the multimedia screen, press the In forward gear, if a trailer is attached, On the multimedia screen, press the dedicated button 11 to obtain a three- press the "Trailer" button from the "Ve- dedicated button 10 for a panoramic dimensional 3D view of the vehicle and...
Page 289
PARKING AIDS – yellow: obstacle between approxi- To activate or deactivate the "Zoom mately 30 and 50 centimetres; auto" function, please refer to the mul- – red: obstacle within approximately timedia instructions. 30 centimetres. Activation/deactivation These indicators also show the loca- tions where obstacles are detected, as 3 indicated by their positions in relation to the "Vehicle"...
Page 290
PARKING AIDS Automatic mode is deactivated: The objects shown on the screen are actually further away on the slope. – after approximately three seconds, – Do not use this func- when shifting from reverse gear to For example, if the screen displays an tion while the door mir- neutral position (on vehicles equipped object at D , the actual distance of the rors are in folded posi-...
Page 291
PARKING AIDS Adjusting the display 3 Driving or reversing towards a pro Limitation of the system operation truding object The system is unable to display ob- From the multimedia screen, when the Position H seems further than position jects located in certain areas. "360° camera" system is displayed, J on the screen.
Page 292
PARKING AIDS – screen split between the rear view/ – front panoramic view; Parking exit warning bird's eye view; – side views/bird's eye view; – panoramic rear view; – 3D view. 3 – side views/bird's eye view (depend- Adjusting the camera settings ing on the vehicle); From the multimedia screen, while the "360°...
Page 293
PARKING AIDS Special feature Activation/deactivation from multi- media screen 1 3 Make sure that the radar area A is not The system's detection ca- obscured (by stickers, mud, snow, To activate or deactivate the function, pability depends on the etc.). refer to the multimedia instructions. vehicle's surroundings (sta- If one of the radars is obscured, the Select "ON"...
Page 294
PARKING AIDS Operation Operating faults If the vehicle is fitted with a towbar recognised by the system and a trailer has been connected, the parking exit warning is automatically deactivated and the following message is dis- 3 played on the instrument panel: "Dri- ving aids unavailable". When the system detects a fault, the "Check side radars" message is dis- played on the instrument panel. Con- sult an approved dealer.
Page 295
PARKING AIDS Limitations to system operation Limitation of the system operation – The radar area should be kept clean and free of any modifications in order to ensure the proper operation of the 3 system. – Small objects (motorcycles, bicycles, pedestrians etc.) moving towards to the vehicle may not be recognised by the sys- tem. Deactivating the function You must deactivate the function if: –...
Page 296
PARKING AIDS Warnings This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. 3 The system should under no circumstances be taken to be an obstacle detector or an anti-collision system.
Page 297
PARKING AIDS Special feature Safe passenger exit Description 3 Using information from the sensors in- stalled on each side of the rear Ensure that zone C around the radars bumper (area C ), the function warns on each side of the rear bumper are the driver: not obstructed (by dirt, mud, snow, –...
Page 298
PARKING AIDS Operation Activating/deactivating the function from the multimedia screen 4 3 When the detected object is very close, a beep will sound, along with When a door is opened, when a mov- the warning message "Lateral obstacle ing object is detected, the warning light To activate or deactivate the function, detected"...
Page 299
PARKING AIDS – there are moving objects (motor- bikes, bicycles, pedestrians, vehicles, This function is an addi- etc.) moving towards or near your ve- tional driving aid and hicle at a low speed that is not consid- may not detect certain ered a risk by the system; vehicles or objects in – the range of the sensors located in- movement in the vicinity of your 3 side the rear bumper is hidden by ob- vehicle. This function is not in any jects, such as other particularly wide way a substitute for the vigilance parked vehicles those parked very...
EMERGENCY CALL If the vehicle is equipped, the emer- gency call function can be used to call the emergency services (without charge) automatically or manually in the event of an accident or illness, re- ducing the time it takes for the emer- 3 gency services to arrive. Note: the emergency call function is operational: – in countries covered by the telemat- ics services and infrastructure associ- ated and compatible with the system; –...
Page 301
EMERGENCY CALL triggered activation of the protective If the button was pressed by mistake, it equipment (seat belt pretensioners, is possible to cancel the call by press- The system operates with a ing and holding the button 6 for airbag, etc.). dedicated battery. The bat- around two seconds, before the call is tery service life is approxi- connected to the call centre.
Page 302
EMERGENCY CALL Without the emergency call feature, the system is not trackable and will not be under constant surveillance. Data is automatically and constantly 3 erased, and the system stores on- ly the last three positions of the vehicle. According to local legislation, data is only sent in the event of an emergency call.
MULTI-SENSE Accessing the menu Spot mode Depending on the vehicle, the Multi- Sense system provides a choice of This mode enables an increased re- several driving modes that influence sponsiveness from the engine and the the driving, ambient lighting and com- gearbox. The steering is firmer. fort: If equipped, the "Chassis control" sus- – all the modes are preconfigured and pension is very rigid (the Sport setting can be customised (ambient lighting, is the default setting) 193.
Page 304
MULTI-SENSE If equipped, the "Chassis control" sus- pension is very supple (the Comfort setting is the default setting) 193. 4 3 0 2 - Yo u r c o m f o r t...
AIR VENTS, HEATING AND AIR CONDITIONING Air vents: air outlets 4 3 0 4 - Yo u r c o m f o r t...
Page 307
AIR VENTS, HEATING AND AIR CONDITIONING 1. Driver’s position air vents 2. Windscreen demister outlet 3. Passenger air vents 4. Side window demister outlet 5. Footwell heater outlets for front passengers 6. Footwell heater outlets for rear passengers 7. Rear passenger central air vents. 4 ...
Page 308
AIR VENTS, HEATING AND AIR CONDITIONING Passenger air vents 3 Driver's position air vents 1 Air flow 4 To control the air flow from the air vents 1 and 3 , press or raise the con- trol 12 to the level desired. To remove bad odours from your vehi- cles, only use the systems designed for this purpose.
Page 309
AIR VENTS, HEATING AND AIR CONDITIONING Rear seats 4. Driver's heated seat activation con- Do not attach any objects trol. to the air vents (e.g. tele- 5. Air-conditioning activation control. phone mounting). 6. Passenger's heated seat activation Risk of damage. control. 7. Heated steering wheel activation control. Do not add anything to 4 ...
Page 310
AIR VENTS, HEATING AND AIR CONDITIONING ration B ). 14 then press upwards again to acti- vate FAST mode. 19. Heated windscreen activation con- When the air conditioning starts in au- trol (configuration B ). tomatic mode, the system returns to the last programme used. Activating the system When the vehicle is started, the sys- tem returns to the last programme Any action on a button oth- used.
Page 311
AIR VENTS, HEATING AND AIR CONDITIONING media screen. The positions are in the – adjusting using the SYNC function to This function quickly de-mists the following order: synchronise the passenger side with windscreen, rear screen, front side the driver's side. windows and door mirrors (depending on the vehicle). It automatically acti- All the air is then directed to the...
Page 312
AIR VENTS, HEATING AND AIR CONDITIONING "Favourites" function Press the button 15 and the built-in Press the button 12 to activate the warning light comes on. This function function. Deactivate ECO mode for enables rapid demisting or de-icing of best performance. the rear screen and de-icing of the rear Air recirculation (isolation of the view mirrors (on equipped vehicles).
Page 313
AIR VENTS, HEATING AND AIR CONDITIONING ECO mode Air conditioning: programming Air conditioning programming 4 You can save several comfort pro- grammes by activating the following From the MULTI-SENSE menu acces- settings: sible from the multimedia screen 21 or – temperature adjustment; by pressing the switch 22 , you can ac- With the vehicle stationary and the en- –...
Page 314
AIR VENTS, HEATING AND AIR CONDITIONING Immediate activation of the air- – the bonnet is open; conditioning Driver's responsibility – you press one of the switches on the control panel; when parking or stop It is possible to carry out immediate –...
Page 315
AIR VENTS, HEATING AND AIR CONDITIONING be present under the vehicle. This is Do not add anything to Use the air conditioning caused by condensation. the vehicle’s ventilation system regularly, even in circuit (for example, to cold weather, running it at Do not open the refrig remove bad odours).
Page 316
AIR VENTS, HEATING AND AIR CONDITIONING The presence and location of the infor- – (1) 0.689 kg mation on label A depends on the ve- – (2) GPWP 4 – (3) 0.003t hicle. Type of refrigerant fluid Do not open the refrig erant circuit. The fluid Type of oil in the air condi may damage eyes or tioning circuit skin.
MULTIMEDIA EQUIPMENT Multimedia screen Please refer to the multime- dia instructions for further information. "USB-C" multimedia ports The USB-C multimedia ports 2 , 5 and 4 6 can be used to charge accessories with a maximum power of 15 Watts (5 Volts) per port. Note: the USB-C 2 multimedia ports also allow for data transfer.
Page 318
MULTIMEDIA EQUIPMENT Microphone Wireless charger 4 Wireless charger 8 322 Microphone 7 (for the telephone and voice assistant) Using the telephone We remind you of the need to conform to the legislation in force con- cerning the use of such equip- ment. 3 1 6 - Yo u r c o m f o r t...
PASSENGER COMPARTMENT EQUIPMENT One-touch electric windows Electric windows These systems operate with the igni- tion on or off, until one of the front doors is opened (limited to about 3 minutes). Driver's responsibility 4 Never leave your vehicle with the card or key in- side, with a child, adult who is not self-sufficient or a pet in the vehicle, even for a short while.
Page 320
PASSENGER COMPARTMENT EQUIPMENT branch), it stops and then lowers again can be seen clearly and no one is in- by a few centimetres. side. When closing the win- dows, ensure that no Impossible to operate the one- part of the body (arm, touch electric window Passenger safety hand, etc.) is protruding The driver can prevent The one-touch electric window is from the vehicle.
Page 321
PASSENGER COMPARTMENT EQUIPMENT Operation Interior lighting The roof becomes com- Map reading lights pletely opaque after the doors are locked or the ve- hicle goes on standby (with the doors unlocked and the engine off, the instrument panel and/or multimedia screen switch off). 4 When the instrument panel and multimedia screen are switched on (welcome se- quence) or when the engine start/...
Page 322
PASSENGER COMPARTMENT EQUIPMENT Sun visor Unlocking and opening the Front sun visor doors or tailgate switches on the timed courtesy lights and lights. Luggage compartment light 4 Touch the reading light 1 , 2 , 3 to acti- vate: – permanent lighting; –...
Page 323
PASSENGER COMPARTMENT EQUIPMENT Accessories socket Accessories sockets 1 4 Connect accessories with a maximum power You can use the accessory sockets 1 of 120 watts (12 V) only. to connect accessory devices. When several accessory sockets are used at the same time, the total power of the con- nected accessories must not ex- ceed 180 watts.
PASSENGER COMPARTMENT STORAGE, FITTINGS Centre console storage com- Sun blind storage compartment Front door storage compart- partment/induction charging ment 1 zone 3 For more information on the induction charging zone, please refer to the mul- timedia instructions. 4 This can be used for storing motorway They can hold a 1.5-litre bottle. tickets, cards, etc. Nothing should be Ensure that no hard, placed on the floor (area...
Page 325
PASSENGER COMPARTMENT STORAGE, FITTINGS Centre armrest storage com- Passenger storage drawer 4 You must not leave any ob- partment 6 ject (starting card, USBflash drive or SDcard, credit card, jewellery, key, coins, etc.) in the induction charging zone 3 when charging your phone. Remove any magnetic 4 cards or credit cards from the phone case before positioning your telephone in the induction charging area 3 .
Page 326
PASSENGER COMPARTMENT STORAGE, FITTINGS Rear doors storage compart- Cup holders 9 ments 10 4 Do not drive with the Depending on the vehicle, the cup holder may be equipped with retaining central armrest in the They may receive a 0.11 gal (0.5 litre) hooks to keep the cup in place.
Page 327
PASSENGER COMPARTMENT STORAGE, FITTINGS Central rear armrest 13 Rear seats storage nets 11 Grab handle 12 4 (depending on the vehicle) This offers support and can be held when the vehicle is moving. You can use it to get into or out of the Ensure that no hard, vehicle.
Page 328
PASSENGER COMPARTMENT STORAGE, FITTINGS Storage compartment 16 in the Tablet holder 18 To access the central armrest 13 , pull the strap 14 . rear central armrest Be sure to store the cup holders 15 before closing the armrest. 4 When closing the arm- rest, make sure that no body parts (arms, hands,...
Page 329
PASSENGER COMPARTMENT STORAGE, FITTINGS Ski rack 19 the strap 20 located behind the central headrest to lower the central seat. Before lowering the central seatback, make sure that the central armrest is prop- erly locked in its housing. 4 With the central seat lowered, before lowering a side seat ensure that no body parts (arms, hands, fingers, etc.) are protrud-...
TRANSPORTING OBJECTS Transporting objects in the luggage Luggage compartment storage compartment Always position the objects transport- Rear parcel shelf, removal ed so that the largest surface is against: 4 – Unhook the two cords 1 from the luggage compartment; – The back of the rear bench seat, for –...
Page 331
TRANSPORTING OBJECTS Towbar Permissible nose weight, maximum permissible towing weight while braked and unbraked: 382. Choice and fitting of towing equipment 4 Towbar (cross member and hitch) not originally fitted to the vehicle: the entire towbar and mountings must not exceed 32 kg. Any towing device must not ob- struct any lighting component or Maximum dimension A : 1,042 mm.
Page 332
TRANSPORTING OBJECTS Roof bars, spoiler and must not prevent the luggage For information on the compartment door from operating cor- rectly. Accessing the mounting points range of equipment adapt- ed to your vehicle, we ad- Spoiler A Vehicles not fitted with longitudinal vise you to consult an approved roof bars dealer. Refer to the fitting instructions for information on how to fit roof bars 4 and conditions of use.
ACCESSING THE ENGINE, LEVELS Unlocking the bonnet catch Opening the bonnet Bonnet To open, pull the handle 1 located on the left-hand side of the dashboard. Before carrying out any operation in the engine compartment, you must switch off the ignition. 5 ...
Page 334
ACCESSING THE ENGINE, LEVELS To close the bonnet again, hold it in the middle and release it around 30 cm In the event of even a Exceeding the maxi above the closed position. slight impact involving mum engine oil level If necessary, press down along the the radiator grille or bon- Under no circumstances...
Page 335
ACCESSING THE ENGINE, LEVELS Adding engine oil Use a funnel or protect the filling neck area to avoid engine oil escap- ing on to a hot part of the engine compartment or a sensitive part (e.g. electrical components). Fire hazard. 5 Filling and/or checking the oil level: when top- ping up or checking the –...
Page 336
ACCESSING THE ENGINE, LEVELS Topping up, filling, draining Do not exceed the "MAXI" Adding engine oil Topping up/filling level and remember to refit Use a funnel or protect the cap 1 and the dipstick the filling neck area to avoid engine oil escap- ing on to a hot part of the engine compartment or a sensitive part –...
Page 337
ACCESSING THE ENGINE, LEVELS Filling and/or checking When working in the en- Never run the engine in the oil level: when top- gine compartment, en- an enclosed space as ping up or checking the sure that the windscreen exhaust gases are poi- oil level, ensure that no wiper stalk is in the park sonous.
Page 338
ACCESSING THE ENGINE, LEVELS Combustion engine air turbocharg- caused to the engine if it runs out of ing coolant 3 (depending on the When working in the en- coolant). vehicle) gine compartment, en- If the level needs to be topped up, only sure that the windscreen use products approved by our Techni- Check the level of the coolants 1 , 2 cal Department which ensure: wiper stalk is in the park and 3...
Page 339
ACCESSING THE ENGINE, LEVELS Levels, filters Topping up When working in the en- After any operation on the hydraulic Brake fluid level gine compartment, en- circuit, a specialist must replace the sure that the windscreen fluid. wiper stalk is in the park Only use fluids approved by our Tech- position. nical Department (and taken from a sealed container).
Page 340
ACCESSING THE ENGINE, LEVELS Windscreen washer reservoir Jets Please note when work- To adjust the height of the windscreen ing close to the engine washer jets, please consult an autho- rised dealer. that it may be hot. The engine cooling fan may also start at any moment. The Before carrying out any action in the engine warning light...
BATTERY ter 5 to 30 minutes of vehicle use with – 2 naked flames and smoking are 12 volt battery the engine stopped to warn the user prohibited; – 3 eye protection compulsory; that the power consuming functions (interior lighting, radio, navigation, ven- – 4 keep away from children; tilation, accessories power supply, etc.) –...
CLEANING Rinse thoroughly beforehand using a Observe local regulations about wash- Bodywork maintenance jet washer: ing vehicles (e.g. do not wash your ve- hicle on a public highway). – spots of tree resin and industrial pol- A well-maintained vehicle will last lution; When washing the vehicle with a high- longer. It is therefore recommended to – mud in the wheel arches and under- pressure cleaning device, please take maintain the exterior of the vehicle reg- neath the body which forms damp...
Page 343
CLEANING Do not do the following Cleaning stickers, decorative films, Doing this could give rise to corrosion etc. or operational faults. Wash the vehicle in bright sunlight or freezing temperatures. Using a roller type car wash You should do the following Do not scrape off mud or dirt without Return the wiper stalk to the Park posi- Use a soft cloth or cotton wool.
Page 344
CLEANING Removal/replacing removable Detergents (washingup liquid, pow warm, soapy water and a sponge and equipment originally fitted in the dered products, alcohol-based wipe with a dry cloth. vehicle products) should not be used. Detergents or dyes must not be Use a soft cloth. used under any circumstances.
Page 345
CLEANING in the vehicle, or have other detrimen- tal effects. 5 M a i n t e n a n c e - 3 4 3...
TYRES any long journey (refer to the label af- Tyres fixed to the edge of the driver's door). Tyre and wheel safety The tyres are the only contact between Incorrect tyre pres the vehicle and the road, so it is es- sures lead to abnormal sential to keep them in good condition. tyre wear and unusually You must make sure that your tyres hot running.
Page 347
TYRES Fitting new tyres One-way tyres Please be aware that a An one-way tyre must only be fitted in poorly tightened or miss- one direction. You must observe this For your safety and to ing valve cap can make direction. comply with the law. the tyres less airtight and If an one-way tyre must be fitted in the When they need to be...
Page 348
TYRES These tyres must, at a minimum, be fit- Tyre pressures should be checked In the event of under-inflation (punc- ted to the two front wheels. when the tyres are cold. tures, under-inflation etc.), the If the tyre pressures cannot be warning light appears on the instru- checked when the tyres are cold, in ment panel 183. In all cases, we would rec- crease the values by 0.2 to 0.3 bar ommend that you contact...
Page 349
TYRES Tyre inflation kit For your safety and to Do not attempt to use comply with the law. the inflation kit if the tyre When they need to be has been damaged as a replaced, only tyres of result of driving with a the same make, size, type and puncture.
Page 350
TYRES – on vehicles fitted with a towing de- The kit is only approved vice, disconnect the towbar socket if needed; for inflating the tyres of – see the information on the infla the vehicle originally tion kit compressor located in the ve- equipped with the kit. hicle luggage compartment and follow It must never be used to inflate the instructions for use;...
Page 351
TYRES tance of 2 miles (3 km), stop and Before using the kit, park check the pressure. – If the pressure is higher than 1.3 bar the vehicle at a sufficient but lower than the recommended pres- distance from traffic, sure (refer to the label affixed to the switch on the hazard edge of the driver's door), adjust it.
Page 352
TYRES Tools The presence of tools in tool kit A or B depends on the vehicle. Please be aware that a poorly tightened or miss- After use, ensure the tools are correct- ing valve cap can make ly stored. the tyres less airtight and may lead to pressure loss. Do not leave the tools Always use valve caps identical to unsecured inside the ve-...
Page 353
TYRES Lever 5 Puncture, emergency spare wheel This can be used to tighten or loosen the towing eye 3 . In case of puncture For your safety, the use of a jack not recom- mended by the manufac- turer is strictly prohibited. The jack is specific to the vehicle and used to change the wheels.
Page 354
TYRES – loosen the central mounting 1 locat- If the vehicle is parked ed at the centre of the emergency spare wheel; on the hard shoulder, – remove the emergency spare wheel. you must warn other Note: in the absence of an emergency road users of your spare wheel or tyre inflation kit, do not vehicle's presence with a warning...
Page 355
TYRES warnings If the spare wheel has been stored for several years, have it checked by your Dealer to ensure that it is safe to use. Vehicle equipped with an emergency spare wheel that differs from the other four wheels: –...
Page 356
TYRES Vehicles equipped with a jack and Changing a wheel wheel brace If the vehicle is parked on the hard shoulder, If necessary, remove the wheel trim. you must warn other Unlock the wheel bolts using the wheel road users of your brace 1 .
Page 357
TYRES If you have a puncture, Do not leave the tools For your safety, the use replace the wheel as unsecured inside the ve- of a jack not recom- soon as possible. hicle as they may be mended by the manufac- A tyre which has been projected during braking. turer is strictly prohibited. punctured should always be in- After use, check that all the tools The jack is specific to the vehicle...
BREAKDOWN RECOVERY Towing: breakdown Leave the card in the ve- Do not leave the tools hicle during towing. unsecured inside the ve- Before towing, set the gearbox to N Risk of the steering hicle as they may be position, unlock the steering column column locking. projected during braking. then release the parking brake.
Page 359
BREAKDOWN RECOVERY Access to towing points Rear towing point 8 – Use a rigid tow bar. If Front towing point 4 a rope or cable is used (where the law allows this), the vehicle being towed must be able to brake. –...
Page 360
BREAKDOWN RECOVERY – when charging, switch off the charg- Do not disconnect the battery while the er before connecting or disconnecting engine is running. Follow the instruc Handle the battery with the battery; tions given by the manufacturer of care as it contains sul- – do not place any metal objects on the battery charger you are using.
Page 361
BREAKDOWN RECOVERY battery supplying the current should have a capacity (amp-hours, Ah) which Handle the battery with is at least the same as that of the dis- care as it contains sul- charged battery. phuric acid which must Ensure that there is no risk of contact not come into contact between the two vehicles (risk of short with the eyes or skin.
Page 362
BREAKDOWN RECOVERY Use terminal 1 (-) and terminal 2 (+) Attach the negative cable B to termi nal 4 (–) of the battery supplying the in the engine compartment. current then to terminal 1 (–). Raise the cover 3 of terminal 2 (+). Start the engine of the vehicle and run it at an intermediate engine speed.
HEADLIGHTS, LIGHTS: REPLACING BULBS Rear and indicator lights LED reversing lights and fog lights Exterior lighting: replacing bulbs Changing bulbs Front headlights LED side light/brake light 1 Changing bulbs 6 Consult an approved dealer. Consult an approved dealer. Your vehicle is fitted with LED lights, LED direction indicator lights 2 contact an Approved Dealer to have them replaced.
Page 364
HEADLIGHTS, LIGHTS: REPLACING BULBS LED high-level brake light 4 LED number plate lights 5 LED side repeaters 6 6 Consult an approved dealer. Consult an approved dealer. Consult an approved dealer. 3 6 2 - P r a c t i c a l a d v i c e...
Page 365
HEADLIGHTS, LIGHTS: REPLACING BULBS Interior lighting: changing bulbs Consult an approved dealer. Light for luggage compartment 5 Reading lights 1, 2 and 3 6 Consult an approved dealer. P r a c t i c a l a d v i c e - 3 6 3...
WIPER BLADES: REPLACEMENT Refitting Replacing the windscreen wiper blades 2 6 To refit the wiper blade 2 , insert it into Check the condition of the its housing in the arm 3 , then clip it un- wiper blades. You are re- til you hear a click. Make sure that the To replace the wipers, first put them in sponsible for their service blade is correctly locked in position.
FUSES Fuses in the passenger compart- Fuse boxes ment B Check the fuse in ques- tion and, if necessary, If any electrical component does not replace it (replacement work, check the condition of the fuses. fuse must have the Fuses in the passenger compart- same rating as the original. ment A If a fuse is fitted with too high a rating, it may cause the electrical circuit to overheat (risk of fire) in the event of an item of equipment...
Page 368
FUSES Fuses in the engine compartment Do not pull the component 5 (risk of Icon Allocation some vehicle equipment being deacti- vated). Direction indicator lights (depending on the vehi- Replacement fuses are available in cle) zone 6 . Luggage compartment Allocation of fuses accessories socket (the presence of certain fuse de...
Page 369
FUSES Before carrying out any action in the engine compartment, you must switch off the ignition 160. 6 For safety reasons, it is forbidden to open the fuse compartment located underneath the flap D . Please note when work- ing close to the engine that it may be hot.
INSTALLATION AND USE OF ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial, etc.), make sure it is compatible with your vehicle. Contact an approved dealer. Before connecting an accessory to a port, ensure that it does not exceed the maximum power authorised for the socket concerned 315, 321.
Page 371
INSTALLATION AND USE OF ACCESSORIES On the driver's side, only use mats suitable for the vehicle, attached with the pre-fitted components, and check the fitting regularly. Do not lay one mat on top of another. There is a risk of wedging the pedals. 6 ...
OPERATING FAULTS The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always con tact an approved Dealer as soon as possible. Using the card POSSIBLE CAUSES ACTION REQUIRED The card does not lock or Card battery is flat.
Page 373
OPERATING FAULTS The starter is activated POSSIBLE CAUSES ACTION REQUIRED 160. The engine will not start. Starting conditions are not fulfilled. The "hands-free" card does not Place the card in the recess provided for work. this purpose on the centre console or 160.
Page 374
OPERATING FAULTS The starter is acti POSSIBLE ACTION REQUIRED vated CAUSES Faulty electri- Consult an approved dealer. cal circuit. On the road POSSIBLE CAUSES ACTION REQUIRED Vibrations. Tyres not inflated to the correct pressure, incor- Check the tyre pressures: if this is not the cause, have rectly balanced or damaged. their condition checked by an approved dealer.
Page 375
OPERATING FAULTS On the road POSSIBLE CAUSES ACTION REQUIRED Fault with the electric Consult an approved dealer. assistance motor. Fault in the assistance system The engine is overheating. The coolant Engine cooling fan not Stop the vehicle, switch off the engine and contact an ap- temperature indicator is in the warning working.
Page 376
OPERATING FAULTS Electrical equipment POSSIBLE CAUSES ACTION REQUIRED The wiper does not stop. Faulty electrical controls. Consult an approved dealer. 361. Direction indicators flashing more quickly. Faulty bulb. The indicators are not working. Faulty electrical circuit or control. Consult an approved dealer. Faulty bulb.
INFORMATION ABOUT THE VEHICLE 5. MTR (Gross Train Weight: vehicle Vehicle identification plates fully loaded, with trailer). 6. MMTA (Maximum Permissible Weight) on front axle. 7. MMTA on rear axle. 8. Reserved for related or additional entries. 9. Not used. 10.
Page 378
INFORMATION ABOUT THE VEHICLE Engine identification, engine specifications Engine identification The QR Code on label A allows emer- 1. Engine type. gency workers using a tablet or smart- 7 2. Engine suffix. phone to immediately access the tech- 3. Engine serial number. nical information useful for working on the vehicle in the event of an accident. Please quote the engine identifica...
Page 379
INFORMATION ABOUT THE VEHICLE Engine specifications Versions E-Tech plug-in hybrid E-tech full hybrid Engine type H5F Turbo H5F Turbo (see engine plate) 1 199 1 199 Cubic capacity (cc) Petrol Type of fuel It is essential to use unleaded petrol with an octane rating matching that indicated on the label af- Octane rating fixed on the fuel filler flap 155. 7 ...
Page 380
INFORMATION ABOUT THE VEHICLE Versions E-Tech plug-in hybrid E-tech full hybrid Fuel types that meet European standards and are compatible with the engines of Unleaded petrol compliant with standard EN 228 vehicles sold in Eu containing up to 5% ethanol in volume. rope (in any other case, contact an Ap- proved Dealer).
Page 381
INFORMATION ABOUT THE VEHICLE Versions E-Tech plug-in hybrid E-tech full hybrid Unleaded petrol compliant with standard EN 228 containing up to 10% ethanol in volume. 7 Only use the spark plugs specified for your vehicle’s engine. The type should be marked on a label affixed inside the engine compartment. If it is not then contact Spark plugs an approved Dealer.
Page 382
INFORMATION ABOUT THE VEHICLE Dimensions (in metres) 7 3 8 0 - Te c h n i c a l s p e c i f i c a t i o n s...
Page 383
INFORMATION ABOUT THE VEHICLE Length 0,946 2,739 1,027 4,712 1,594 1.613 unladen, vehicle fitted with a rigid antenna 1,616 1,843 1.863 with door mirrors folded in 7 2.083 with door mirrors folded out Te c h n i c a l s p e c i f i c a t i o n s - 3 8 1...
Page 384
INFORMATION ABOUT THE VEHICLE Weights (in kg) The weights indicated are for a basic vehicle without optional fittings: they vary according to your vehicle's equip ment. Consult your approved Dealer. Maximum Permissible All-Up Weight (MMAC) Weights indicated on the manufacturer's plate 375 Maximum Permissible Weight (MMTA) Gross Train Weight (MTR) Braked Towing Weight *...
REPLACEMENT PARTS AND REPAIRS Original parts are based on very stringent specifications and are subjected to specific tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out in the approved dealer network with original parts are guaranteed according to the conditions stated on the back of the repair or- der.
SERVICE SHEETS VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........ □ Anticorrosion check: OK □ Not OK* □ Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ 7 ........ □ Anticorrosion check: OK □ Not OK* □ Date: Miles (km): Invoice number: Comments/miscellaneous...
Page 387
SERVICE SHEETS VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........ □ Anticorrosion check: OK □ Not OK* □ Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ 7 ........ □ Anticorrosion check: OK □ Not OK* □ Date: Miles (km): Invoice number: Comments/miscellaneous...
Page 388
SERVICE SHEETS VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........ □ Anticorrosion check: OK □ Not OK* □ Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ 7 ........ □ Anticorrosion check: OK □ Not OK* □ Date: Miles (km): Invoice number: Comments/miscellaneous...
Page 389
SERVICE SHEETS VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........ □ Anticorrosion check: OK □ Not OK* □ Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ 7 ........ □ Anticorrosion check: OK □ Not OK* □ Date: Miles (km): Invoice number: Comments/miscellaneous...
Page 390
SERVICE SHEETS VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........ □ Anticorrosion check: OK □ Not OK* □ Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ 7 ........ □ Anticorrosion check: OK □ Not OK* □ Date: Miles (km): Invoice number: Comments/miscellaneous...
Page 391
SERVICE SHEETS VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........ □ Anticorrosion check: OK □ Not OK* □ Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ 7 ........ □ Anticorrosion check: OK □ Not OK* □ Date: Miles (km): Invoice number: Comments/miscellaneous...
ANTICORROSION CHECK If the continuation of the warranty is subject to repair, it is indicated below. VIN: .................. Date of repair: Stamp Corrosion repair operation to be carried out: Date of repair: Stamp 7 Repair to be carried out: 3 9 0 - Te c h n i c a l s p e c i f i c a t i o n s...
Page 393
ANTICORROSION CHECK If the continuation of the warranty is subject to repair, it is indicated below. VIN: .................. Date of repair: Stamp Corrosion repair operation to be carried out: Date of repair: Stamp 7 Repair to be carried out: Te c h n i c a l s p e c i f i c a t i o n s - 3 9 1...
Page 394
ANTICORROSION CHECK If the continuation of the warranty is subject to repair, it is indicated below. VIN: .................. Date of repair: Stamp Corrosion repair operation to be carried out: Date of repair: Stamp 7 Repair to be carried out: 3 9 2 - Te c h n i c a l s p e c i f i c a t i o n s...
Page 395
ANTICORROSION CHECK If the continuation of the warranty is subject to repair, it is indicated below. VIN: .................. Date of repair: Stamp Corrosion repair operation to be carried out: Date of repair: Stamp 7 Repair to be carried out: Te c h n i c a l s p e c i f i c a t i o n s - 3 9 3...
Page 396
ANTICORROSION CHECK If the continuation of the warranty is subject to repair, it is indicated below. VIN: .................. Date of repair: Stamp Corrosion repair operation to be carried out: Date of repair: Stamp 7 Repair to be carried out: 3 9 4 - Te c h n i c a l s p e c i f i c a t i o n s...
Page 397
ANTICORROSION CHECK If the continuation of the warranty is subject to repair, it is indicated below. VIN: .................. Date of repair: Stamp Corrosion repair operation to be carried out: Date of repair: Stamp 7 Repair to be carried out: Te c h n i c a l s p e c i f i c a t i o n s - 3 9 5...
Page 398
ANTICORROSION CHECK If the continuation of the warranty is subject to repair, it is indicated below. VIN: .................. Date of repair: Stamp Corrosion repair operation to be carried out: Date of repair: Stamp 7 Repair to be carried out: 3 9 6 - Te c h n i c a l s p e c i f i c a t i o n s...
Page 399
ALPHABETICAL INDEX Symbols A B C D E F G H I J L M N O P R S T U V W Symbols Assisted parking, 268, 274, 277 Audible and visual signals, 151 "Hands-free" card: battery, ...
Page 400
ALPHABETICAL INDEX Card: use, 52 Cruise control, 248, 252 Card remote control, 50 Cruise control - Speed limiter, 248 Catalytic converter, 169 Customising the vehicle settings, 130 65 Central door locking, ...
Page 401
ALPHABETICAL INDEX Electric windows, 317 Front seat belt pretensioners, 85 Electronic parking brake, 171, 174 Front seats, 73 Electronic stability program: ESC, 187 Front seats with electric controls, 76 187 73 Emergency brake assist, Front seats with manual control, ...
Page 402
ALPHABETICAL INDEX Hill descent control, 187 Lighting: see-me-home lighting, 143 Hill start assistance, 187 Lighting signals, 143, 151 Horn, 151 Lights: dipped beam headlights, 143 151 Lights: direction indicator lights, 143, ...
Page 404
ALPHABETICAL INDEX Side protection devices, 90 Tyre inflation kit, 349, 351 Special features of petrol vehicles, 169 Tyre pressure, 178, 183, 346, 351, 354 Speed limiter, 248 Tyre pressure loss warning, ...
Page 406
RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 122-122 BIS, AVENUE DU GENERAL LECLERC 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / renaultgroup.com NU 1537-2 – 77 11 416 191 – 04/2024 – Edition anglaise...
Need help?
Do you have a question about the RAFALE and is the answer not in the manual?
Questions and answers
Is there a mechanism to open the boot from inside the Rafale