Related Manuals for Dacor 100500
Summary of Contents for Dacor 100500
- Page 1 I o n n str u ct I o n s u I lt e f r I g e r ato rs Part No. 100500 Rev. A...
-
Page 3: Table Of Contents
Built-In Any questions or problems with the installation should be ® directed to your Dacor Department at 800.793.0093 or email customerservice@ dacorworld.com. You can also visit our website at www.dacor.com. afeTy DANGER WARNING CAUTION dealer or the Dacor Customer Service ®... -
Page 4: Design Specifications
RoduCT imensions ◊ The depth from the front of the top grill (w/o decorator panel) to the back of the refrigerator chassis is 25 1/4” (641mm). ◊ The depth from the rear of the top grill to the back of the refrigerator chassis is 23 13/16” (605mm). ◊ The power cord is 40” (1016mm) long. ◊ The height from the top of the top grill to floor with the leveling legs in the down position is 83 3/8” (2118mm) ◊... -
Page 5: Custom Overlay Panels
This application is often accomplished by using three panels: the decorative front panel, a spacer panel of .10-inch thickness, and a 1/4-inch backer panel. (see page 4) Dispenser Freezer Panel Non-Dispenser Refrigerator Freezer Panel Panel... - Page 6 2” (51mm) 14 1/2” (368mm) Side Panel Specifications 68 1/8” (1730mm) If using side panels 34 1/16” (865mm) with the Dacor Built-In Refrigerator, 48 1/8” (1222mm) they will need to be 1/4” (6mm) thick. 17 1/2” (445mm) 68 1/8” (1730mm) 26 1/4”...
- Page 7 Custom Toe Kickplate Specifications If using custom toe kickplate with your Dacor refer to the following specifications. Panel thicker than 3/16" 6 1/4" 5 5/8" 15/16" Typ 4 13/16" 7/8" 5/16" 2 3/16" Typ 1 13/16" 3/4" Typ Non-Dispenser Custom Handle Specifications Before installing the custom panel assembly, the custom handle hardware must be installed.
- Page 8 90˚ Door Opening Cabinet Trim 23 7/8" to Rear of Cabinet 0" 1/4" 1/2" 3/4" 1" 1 1/4" 1 1/2" 1 3/4" 2" 2 1/4" 2 1/2" Door Open 2 3/4" 3" @ 90˚ 3 1/4" 3 1/2" 3/4" Overlay Panel esign PeCifiCaTions...
-
Page 9: Site Preparation
Site Preparation The solid sofit or ceiling should be within 1” (25mm) above the refrigerator. It the solid sofit is higher than 1” (25mm) or one is not available, then the refrigerator must be braced to prevent tipping during use. -
Page 10: Electrical Requirements
◊ The solid sofit or ceiling should be within 1” (25mm) above the refrigerator. If the solid sofit is higher than 1” (25mm) or one is not available, then the refrigerator must be braced to prevent tipping during use. If the anti-tip blocking is need. -
Page 11: Installation Instructions
TIP OvER HAzARD – Refrigerator is top heavy and tips easily when not completely installed, Keep doors taped closed until refrigerator is completely installed. Use two or more people to move and install refrigerator. Failure to do so can result in death or serious injury IMPORTANT: ◊... -
Page 12: Water Line Connection
(Use a 3/8” socket to raise and lower the unit.) ◊ Check to see whether the refrigerator is level left to right, by opening the doors and place a level on top of the refrigerator frame as shown. -
Page 13: Install Custom Panels
Away from Door With a phillips screwdriver, remove the trim from the freezer and refrigerator doors. Slide the panel into the frame on the door. With the panel in position, replace the trim. Be sure that the panel is inserted completely into the channel for proper fit and alignment. -
Page 14: Adjust Door Hinges
nsTallaTion Remove the four #15 Torx plastic collar screws from the fountain/escutcheon collar. Place the fountain/ escutcheon collar onto the backer panel. Use tape to hold in place. Open the freezer door and slide panel onto the door. 10. The holes in the fountain/escutcheon collar should line up with the mounting... -
Page 15: Side Panel Installation
Side Panel Installation If using side panels with the Dacor Built-In Refrigerator, ® they will need to be 1/4-inch thick. Slide the panel into position and secure with screws indicated by the shaded area. A 3/16-inch spacer is required between the cabinet and side panel. -
Page 16: Installation Check List
The importance of the proper installation of your Dacor Built-In Refrigerator cannot be overemphasized. Proper installation is the responsibility of the homeowner. IMPORTANT: To ensure a safe and proper installation, the following checklist should be competed by the installer to ensure that no part of the installation has been overlooked. - Page 17 oTes...
- Page 18 oTes...
- Page 20 Web Site: www.dacor.com Phone: (800) 793-0093 The information and images in this book are the copyright property of Distinctive Appliances, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Distinctive Appliances, Inc.
Need help?
Do you have a question about the 100500 and is the answer not in the manual?
Questions and answers