Speaka Professional SP-SSD-WN01 Instruction Manual

Instructions of Safety and Warnings:
• Any failure to comply with the safety and installation instructions in this manual may cause serious bodily injury.
• Overlooking any part of the instructions, warnings and additional information marked with the "Note" and "
may result in serious damage to the system or its components.
• Children should never be allowed to operate or touch the product without direct supervision of an adult. Users
should prevent children from being near or around the desk during operation.
• Disabilities and/or lack of experience and knowledge should be prevented from using the product unless under
supervision or assisted during use and operation.
• Never sit on or exceed the rated weight of the desk.
Electrical Safety Instructions:
CAUTION
The product is powered by electricity. In order to avoid burns, fire and electric shock, please read the
instructions carefully.
Don't clean the product with water
while the power is still connected.
Don't disassemble or replace components
while the power is still connected.
Never operate the system with a damaged cord
or plug. Please contact your point of purchase to
replace the damaged parts.
Other Safety Instructions:
CAUTION
·Remove any obstacles from the area around the desk during assembly and subsequent use.
·Organize all cords and wires to prevent any possible tripping or accidents from occurring.
·Never attempt to modify or change the desk frame or components that operate the desk.
·Don't add anything to the adjustable junctions of the desk frame.
·The desk is rated for Indoor Use Only.
2 Troubleshooting Guide
Description
Error No.
E01/E07 Electrical problem has occurred. Plug out the power and re-plug.
System overheating. Stop operating and allow your desk to remain idle for
HOT
approximately 18 minutes.
The columns don't go together. Reset the system.
E02
E04 System's communication has an error. Plug out the power and re-plug.
E05 Collision avoidance system has activated. Remove all the objects within the range of motion.
Electrical problem has occurred. Plug out the power and re-plug. If it doesn't work, replace the
E06
control box.
·Collision avoidance system has activated. Remove all the objects within the range of
motion.
·The control box isn't placed well. Please make sure the control box is properly attached
E08
to the desk frame as the instruction manual or placed well on the even surface.
·The power cords have pulled the control box. Manage the cables and keep them from
pulling the control box.
The motor cords were disconnected, Check the connection or replace the motor cords.
E11
Electrical problem has occurred. Plug out the power and re-plug. If it doesn't work, replace the
E12
control box.
Motor wires may be broken. Check the connection or replace the motor cords.
E13
E14 Hall wires may be broken. Check the connection or replace the motor cords.
E15 Short circuit. Replace the motors or columns.
Overload leads to the motor to fail to drive. Remove the items from the desktop then reset
E16
the system.
Desk move in wrong direction. Check the connection or replace the motor cords.
E17
Overload has occurred. Remove the items from the desktop.
E18
Memory can not be read. Plug out the power and re-plug. If it doesn't work, replace the
E42
control box.
E43 Collision avoidance system failure. Replace the control box.
"
Never operate the system if it's in moist
environment or its electrical components
have contact with liquids.
Don't operate the system if the control box
makes noise or odor.
Alterations of the given power unit and
control box aren't allowed.
ELECTRIC SIT-STAND DESK
Instruction Manual
Item No.: 3015282
SP-SSD-WN01
3 Custom Programming Guide
Button
Function:
Adjust
s-1
To Adjust Minimal
Height Limit
(72~110cm/28.3"~43.3")
Press "M" and "T" buttons simultaneously for about 5 seconds until the unit emits one beep and the display
flashes "S-1". Press "UP"/"Down" button to switch from "S-1"to "S-7". The custom mode will be active
Step 1:
while flashing for approximately 10 seconds but when there are no activations made within the mentioned time,
Preparing
the custom mode will go exit.
When the display is flashing "S-2",
When the display is
press "M" button once and the Current
flashing "S-1", press "M"
Maximum Height Limit is displayed
button once and the
120
Current Minimal Height (
Step 2:
Limit is displayed ( by "Down" to set your desired height.
Programming
72.0
default). Then press (Note: For display range reason, the display
"UP"/"Down" to set your will not count the number immediately as
desired height. you press the up and down buttons under
the setting of the metric system.)
Press "M" to save.
Step 3: "L-S"- successful
Saving
"L-F"- failing
s-4
To Adjust Anti-Collision To Adjust Anti-Collision
Sensitivity Sensitivity (Gyro Sensor)
(Level 0~Level 8)
(Current Sensor Downward
Movement)(Level 0~Level 8)
Press "M" and "T" buttons simultaneously for about 5 seconds until the unit emits one beep and the display
flashes "S-1". Press "UP"/"Down" button to switch from "S-1"to "S-7". The custom mode will be active
Step 1:
while flashing for approximately 10 seconds but when there are no activations made within the mentioned time,
Preparing
the custom mode will go exit.
When the display is
When the display is flashing flashing "S-5" , press "M"
button once and the
"S-4" , press "M" button once
Current Anti-Collision
and the Current Anti-Collision
Step 2:
4 Sensitivity is displayed
Programming Sensitivity is displayed (
4
(
by default). Then press "UP"/
press "UP"/"Down" to
"Down" to set your desired
set your desired level.
level.
Press "M" to save. Press "M" to save.
Step 3:
"S-S"- successful "S-S"- successful
Saving
"S-F"- failing "S-F"- failing
Note:
·To abort a custom process, press the"T" button or wait approximately 10 seconds until the display
automatically
returns to show the height of the desk.
·The max./min. height limit displayed in the custom mode doesn't include the thickness of desktop.
Confirm/
Back/Cancel
Next/Save
s-2 s-3
To Adjust Maximum To Adjust Anti-Collision Sensitivity
Height Limit (Current Sensor Upward Movement)
(82~120cm/32.3"~47.2") (Level 0~Level 8)
When the display is flashing
"S-3", press "M" button once
by default). Then press "UP"/
and the Current Anti-Collision
Sensitivity is displayed (
by default). Then press "UP"/
"Down" to set your desired level.
Press "M" to save. Press "M" to save.
"H-S"- successful "S-S"- successful
"H-F"- failing "S-F"- failing
s-5 s-6
To Change the Current To Change the Screen
Height and Desktop Lock Function
(0:OFF/1:ON)
Thickness
(0~5cm/0~2.0")
When the display is
When the display is flashing
flashing "S-7" , press "M"
"S-6" , press "M" button
button once and the
once and the Current
Current Screen Lock
Desktop Thickness is
Setting is displayed.
0.0
displayed.( by default). 1
by default). Then ( by default). Press
Press "UP"/"Down" to set
"UP"/"Down" to set your
your desired height.
desired locking function.
Press "M" to save. Press "M" to save.
"T-S"- successful "A-S"- successful
"T-F"- failing "A-F"- failing
4
s-7