Advertisement
Quick Links
Installation Instructions
Model:
Description:
Part Number:
Assembly Time:
Before you begin, read through these instructions and check that
all parts are present. Always disconnect negative battery terminal,
prior to installation. Please note that MB Quart cannot assume any
responsibility for damage resulting from incorrect installation.
No.
1
GMR-LED with Housing (MBQT-RAD-1)
2
6.5in Dash Speakers (MBQT-FPOD-1)
3
8" Subwoofer w/Enclosure (MBQT-SUB-1)
4
MBQT-ACC-1
5
NA2-400.1 Amplifier
6
NA2-400.2 Amplifer
1
Bojo Tool
2
Panel Clip Pliers
3
10mm open box wrench
4
10mm and 12mm socket
5
½" socket
6
Rachet
7
Small flat head screwdriver
8
Phillips screwdriver
9
3mm and 5mm Allen Wrench
10
¼" and ½" drill bit or stepper bit
11
1" hole saw
12
Drill
13
Rotary tool similar to a Dremel
14
Heat Gun or Lighter
15
Crimper
Honda Talon
Stage 3 Install
MBQT-STG3-1
150 Mins (2.5-Hours)
Parts List
Component Name
Tools Required
Page 1 of 32
Qty
1
2
1
1
1
1
Advertisement
Related Manuals for MB QUART MBQT-STG3-1
Summary of Contents for MB QUART MBQT-STG3-1
- Page 1 Assembly Time: Before you begin, read through these instructions and check that all parts are present. Always disconnect negative battery terminal, prior to installation. Please note that MB Quart cannot assume any responsibility for damage resulting from incorrect installation. Parts List...
- Page 2 Disassembly ● Remove hood by turning two latches ● Remove four 10mm bolts, four push pins, and five 5mm allen bolts to remove top of dash ● Remove half mud guard with six push pins Page 2 of 32...
- Page 3 Disassembly ● Release latch at front of driver and passanger lower cushions to remove ● Remove two 12mm bolts on front of drivers seat ● Slide driver seat forward and remove two 12mm bolts on rear of seat Page 3 of 32...
- Page 4 Disassembly ● Remove drivers seat ● Remove two push pins on front of passenger seat and then remove the covers ● Remove two 12mm bolts and two 12mm nuts on the passenger seat base Page 4 of 32...
- Page 5 Disassembly ● Remove passenger seat from vehicle ● Pull top fuse access panel toward front of vehicle and remove ● Using a small flat head screwdriver push in the center and remove the six clips on the passenger side Page 5 of 32...
- Page 6 Disassembly ● Remove the five push pins on the driver side console on the passenger side ● Place gear selector to “H” and remove the top of the center console ● Lift up the bottom half of the steering column rubber boot Page 6 of 32...
- Page 7 Disassembly ● Remove the two push pins behind the rubber boot ● Remove the two push pins on the bottom of steering column cover ● Remove the bottom steering wheel cover Page 7 of 32...
- Page 8 Disassembly ● Remove one 5mm allen bolt and one push pin from the drivers kick area ● Remove two 5mm allen bolts from behind glove box door ● Remove one push pin in the back of the glove box Page 8 of 32...
- Page 9 Disassembly ● Remove three push pins from below the glove box ● Remove glove box ● Remove one 5 mm allen bolt and one push pin from passenger kick area Page 9 of 32...
- Page 10 Front Speaker Pod Installation ● Drill a ½” hole, 5/8” down from the edge, and 2 ¼” over (control the depth of bit to not go to deep) ● Pass the wire from the driver side pod through the hole you drilled ●...
- Page 11 Front Speaker Pod Installation ● Install the M6 x 40mm bolt and washer through the enclosure into the factory bolt location ● Tighten the 5/16” bolt in the fender area ● Repeat previous steps on passenger side Page 11 of 32...
- Page 12 Radio & Dash Kit Installation ● Place the metal u-bracket at the top of the pocket and mark the bottom portion to be cut out with a rotary tool ● Drill two ¼” holes using the u-bracket as a guide in the back of the pocket ●...
- Page 13 Radio & Dash Kit Installation ● Slide the dash panel with the bevel and MB Quart logo facing outward like the image ● Pass the wires from the radio through the hole below the u-bracket in the pocket ● Install four M4 cap head bolts...
- Page 14 Radio & Dash Kit Installation ● Install covers on each side of radio Page 14 of 32...
- Page 15 Amplifiers and Plate Installation ● Adjust the NA2-400.2 amplifier’s gain and crossover settings as pictured. NOTE Gains all to the last “L” on Level HPF to 100Hz going just past “P” on LP LPF is turned all the way down X-Over to HP ●...
- Page 16 Amplifiers and Plate Installation ● Install the NA2-400.2 amplifier as pictured with four M4 Philips screws, washers, and lock nuts ● Install the rubber c-clamp around the tube as pictured ● Slide the top amplifier mount between the frame and top of dash as pictured Page 16 of 32...
- Page 17 Amplifiers and Plate Installation ● Install the M6 button head bolt through the plate and c-clamp attaching from the bottom with a washer and lock nut ● Install the NA2-400.1 amplifier next to the two channel amplifier and secure with three M4 Philips screws, washers, and lock nuts NOTE May need to shift amplifier plate...
-
Page 18: Wiring Installation
Wiring Installation ● Connect the speaker harness to the NA2-400.2 amplifier and route the driver and passenger speaker leads to the appropriate kick area ● Connect bullets of amplifier harness with respective front kick pods ● Plug subwoofer extension harness into the NA2-400.1 amplifier Page 18 of 32... - Page 19 Wiring Installation ● Route subwoofer and rear speaker harness down toward center console going to the rear of the vehicle. (Stage 3 does not include rear speakers but run harness for easy upgrade in the future) NOTE Use a fish tape passed from cabin toward front of vehicle to help pull wires ●...
- Page 20 Wiring Installation ● Install power harness to each amplifier (Connector with bullets connects to NA2-400.2) ● Connect bullets from power harness to speaker harness (This is if you want to add optional LED rings at the speaker locations) ● Connect Delphi connector on power harness into the radio harness Page 20 of 32...
- Page 21 Wiring Installation ● If you don’t already have a buss bar installed you can connect to factory wiring (but we highly recommend a buss bar kit) These are available from many aftermarket companies like XTC Power Products ● Plug RCA into the NA2-400.2 and run to the front RCA outputs of the radio ●...
- Page 22 Wiring Installation ● Drill a 1” hole in the side of the glovebox 3” from the front for the USB / AUX Port ● Place the glove box back in the vehicle (we will install hardware during assembly portion of the manual) ●...
-
Page 23: Subwoofer Installation
Subwoofer Installation ● Install four brackets with 5/16 bolts and washers leaving them loose ● Place subwoofer enclosure under driver seat area and pass the harness through small opening pictured and pull toward top of center console Page 23 of 32... - Page 24 Subwoofer Installation ● Connect the subwoofer enclosure harness to the amplifier harness in center console ● Align plates to seat mount holes and tighten CORRECT ALIGNMENT INCORRECT ALIGNMENT ● All plates aligned Page 24 of 32...
- Page 25 Reassembly ● Install three push pins from below the glove box ● Install one push pin in the back of the glove box ● Install two 5mm allen bolts from behind glove box door Page 25 of 32...
- Page 26 Reassembly ● Install the bottom steering wheel cover ● Install the two push pins on the bottom of steering column cover ● Install the two push pins behind the rubber boot Page 26 of 32...
- Page 27 Reassembly ● Reposition bottom half of the steering colum rubber boot ● Place gear selector to “H” and install the top of the center console ● Install the five push pins on the driver side console like on the passenger side Page 27 of 32...
- Page 28 Reassembly ● Using a small flat head screwdriver, push in the center and install the six clips on the passenger side ● Install top fuse access panel ● Install passenger seat from vehicle Page 28 of 32...
- Page 29 Reassembly ● Install two 12mm bolts and two 12mm nuts on the passenger seat base ● Install two push pins on front of passenger seat and then remove the covers ● Install drivers seat Page 29 of 32...
- Page 30 Reassembly ● Slide driver seat forward and install two 12mm bolts on rear of seat ● Install two 12mm bolts on front of drivers seat ● Release latch at front of driver and passanger lower cushions to install Page 30 of 32...
- Page 31 Reassembly ● Install new full mud guard with kit with 6 push pins previously removed and 8 new push pins in ● Install four 10mm bolts, four push pins and five 5mm allen bolts to remove top of dash ● Install hood by turning two latches Page 31 of 32...
- Page 32 The Bluetooth ® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use such marks by MB Quart is under license. All product names, logos, and brands are property of their respective owners. All company, product and service names used in this literature are for identification purposes only.
Need help?
Do you have a question about the MBQT-STG3-1 and is the answer not in the manual?
Questions and answers