La Marzocco strada s Manual
  1. Manuals
  2. Brands
  3. La Marzocco Manuals
  4. Coffee Maker
  5. strada s
  6. Manual

La Marzocco strada s Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

manual
strada s

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the strada s and is the answer not in the manual?

Questions and answers

Related Manuals for La Marzocco strada s

Summary of Contents for La Marzocco strada s

  • Page 1 s...

  • Page 2: Table Of Contents

    Operating Manual V1.0 - 05/2023 MAN.32.1 Chapters La Marzocco S.r.l. page 3 1. General Warnings and Safety Specifications Via La Torre 14/H Località La Torre page 8 2. Definition of Available Models 50038 Scarperia e San Piero (Firenze) - ITALIA page 11 3.

  • Page 3: General Warnings And Safety Specifications

    1. General Warnings and Safety Specifications years of age) with reduced WARNING CAUTION This appliance is for professional As already mentioned in physical, sensory or mental use only and should be installed the preceding notes, the capabilities, or lack of in locations where its use and manufacturer shall not be held experience and knowledge,...
  • Page 4 on any further and contact your part of the product and instructions, and must be must be supplied to users. dealer or retailer immediately. They performed by qualified and Users are asked to read will send out specialized personnel authorized personnel. the enclosed warnings and authorized to perform service on 8) Incorrect installation may...
  • Page 5 10) Furthermore, you must inappropriate and dangerous. (rain, sun, etc.); ensure that the capacity of The manufacturer shall not be held • do not allow children or available electrical system responsible for any damages caused untrained people to use is suitable for the maximum by improper and/or irrational use.
  • Page 6 or breaks down, disconnect recommended that the power com. it from electrical network (as supply cable be fully unfurled. 21) The appliance should be described in the preceding 18) Do not obstruct air intake placed on a flat counter and point) and close water supply and exhaust grilles and, in in settings with the following...
  • Page 7 • wireless network 2.4 GHz; • La Marzocco app available • 1.5 m of reinforced plastic current not exceeding 30 mA at the official stores Play tubing for drainage is installed. Store and App Store.

  • Page 8: Definition Of Available Models

    2. Definition of Available Models This operating manual refers exclusively to the following models, of our own manufacture: STRADA, model S with 2 and 3 groups Legend Main Switch Pressure Gauge (steam boiler) Pressure Gauge (coffee boiler) Brew Groups Cup Warmer Button Hot Water Button Digital Display Steam Wand...
  • Page 9 1) General Description by temperature probe and PID controller. is a list of effective volume and power The machine is built in 2 and 3 coffee The steam boiler has various fittings used ratings according to the number of groups group versions and is essentially composed for safety devices, for supplying hot water installed:...
  • Page 10 The exterior consists of painted and precise reading of the TDS and total stainless sheet steel panels. To provide hardness. good aesthetics, to optimize ergonometrics STRADA S 3AV XY000000 However, if a water softener with salt for the operator and to reduce the chance 05/23...

  • Page 11: Installation

    WATTAGE WATTAGE AC220-240V/60Hz 24.6 current not exceeding 30mA is AC208-240/60Hz 5666 21-24 1600 3000 5666 SEE ELECTRICAL AC380/50Hz 10.3 installed. STRADA S CONNECTIONS 33.8 AC220-240V/60Hz 2400 4000 7783 29-33 AC208-240/60Hz 7783 FOR DETAILS 14.8 AC380/50Hz WARNING POWER CORD: 3 X WIRES...
  • Page 12 WARNING WARNING WARNING At each installation, the Hazardous voltage disconnect This appliance is not intended machine should be equipped from power supply before for use by persons (including with a new set of tubes for servicing. children) with reduced physical, plumbing and related gaskets.
  • Page 13 WARNING HERE THE POSITION OF THE POWER CORD AND 215 mm WATER INLET HOSES In order to prevent cracks 8,5 in. HERE THE POSITION WHERE WE 100 mm FROM ∅80 TO ∅100 mm SUGGEST TO MAKE THE HOLE 4 in. or leakage: do not store or FROM ∅3 in.
  • Page 14 1) Installation guide If the pressure and flow are not adequate, For best results, STRADA needs a air bubbles may develop within the gears. minimum flow of water in input of 100 l/h This is called cavitation. Cavitation can and a pressure of 2.5 bar. impair the performance of the espresso machine.
  • Page 15 Pressure higher than 9 bar Flow rate lower than 100 l/h Installation pressure reducer immediately after the water treatment system, upstream of the rotary pump. Installation of the rotary pump (set to 9 bar) immediately after the pressure reducer, upstream of the tee. POWER SUPPLY STEAM COFFEE...
  • Page 16 2) Accessories 4) Flowmeter safety removal In order to proceed with installation, it is Before switch on, remove the clamp from necessary that the following are available: the flowmeter located inside the machine, as • Pipes carrying drinking water with a indicated by the adhesive label applied on 3/8”G (BSP) end connection;...
  • Page 17 4°d) and less than 10°f (100ppm, 6°d), 6) Electrical connections - View of the connectors; pH should be between 6.5 and 8.5 and a) Power supply cord the quantity of chlorides be less than • This is the main power supply cable 30mg/l .
  • Page 18 hose connection on the left side of the Water specifications table espresso machine, secure with included Min. Max. hose clamp. Connect the other end to a T.D.S. suitable waste water collection system. In case such a system is not available, Total Hardness drained liquids may be collected in a Total Iron (Fe...

  • Page 19: Machine Operation And Coffee Preparation

    4. Machine Operation and Coffee Preparation group assemblies. CAUTION WARNING To remove the air from the boiler, or “bleed Never remove the filter holder This machine is designed only for the groups”, it will be necessary to remove when water is being delivered. preparing coffee and hot drinks.
  • Page 20 will be switched on, activating the auto-fill is necessary to adjust the expansion valve • Turn on the hot water valve for the solenoid valve and the motor pump. This (see the picture below about the three time necessary to allow the following will fill the steam boiler to a predetermined coffee boiler expasion valves) in such a quantities of water to be brewed:...
  • Page 21 5) Brewing coffee from exceeding 11-12 bar. too slowly (drop by drop) nor too quickly Now you can brew an espresso. Disengage In case the pressure exceeds 12 bar, (quick light brown flow). A general rule one of the portafilters, fill the filter with you must adjust the expansion valve by is that a double dose should dispense ground coffee, tamp the ground coffee...

  • Page 22: Dispensing Steam And Hot Water

    5. Dispensing Steam and Hot Water 1) Steaming milk or other liquids This condition is undesireable and can 2) Preparing tea and other hot drinks. In order to allow for any condensed water cause contamination in the steam boiler. HOT WATER in the wand to be released ALWAYS allow After use remember to purge the wand by some steam to be discharged by turning on...

  • Page 23: Maintenance And Periodic Cleaning Operations

    6. Maintenance and Periodic Cleaning Operations WARNING WARNING WARNING If the above-mentioned The machine must be installed so This machine is for professional instructions are not adhered that qualified technical presonnel use only and should be installed to the manufacturer cannot be in locations where its use and can easily access it for eventual held responsible for damage to...
  • Page 24 2) Cleaning filters Rinse thoroughly with clean water. Install 6) Cleaning the hot water and steam nozzles - Put 2 or 3 teaspoons of detergent powder and run hot water through each group Steam nozzles must cleaned for coffee machines in about 1/2 a litre several times with the screen installed.

  • Page 25: Commissioning And Demolition

    each steam wand for at least one minute. follow these safety indications: Turn on the hot water valve for the time Disconnect the machine from the water necessary to allow the following quantities mains or interrupt the water connection of water to be brewed: via a mains tap.

  • Page 26: Mandatory Maintenance And Check-Up Operations

    8. Mandatory Maintenance and Check-up Operations These operations are in addition to the Maintenance and Periodic Cleaning Operations as specified in Chapter 6. The following maintenance and check-up operations sould be carried out by a qualified technician. The time required for the periodic maintenance is determinated by the quantity of daily work and/or coffee consumption. N.B.

  • Page 27: Precision Scale

    9. Precision Scale WARNING Legend Handle with care maximum load Scale crosspiece 1Kg do not lift. Drain grille Scale individual grid WARNING Removable drain tray The individual grid of the scale is a fragile component, handle and store with care. WARNING The height of the bottom tray is fixed.
  • Page 28 - To avoid contact with dirt before placing the filter holder, clean and dry the grid; - Use only original La Marzocco filters and - Please be careful during the cleaning filter holders, identified by the following...
  • Page 29 3) Removing the electronic box To remove the electronic box you need to remove the lower front panel, unscrew and remove the lower screws , loosen the upper screws without removing them and move the scale crosspiece up. Now you can access the electronic box or remove it.

  • Page 30: Software Programming Guide

    10. Software Programming Guide “Barista” Programming La Marzocco 09:30 92.0°C page Press and hold the T3 button for 5 seconds. Menu Press B3 to Exit Group Dose Backflush Water Dose Coffee Boiler Settings INDIVIDUAL Settings Settings page 42 page 57...
  • Page 31 “Barista” Programming Preinfusion H20 Sensor - TDS Total Hardness Configure Settings 000.0 ppm 000.0 ppm Gateway page 65 page 69 page 70 page 71 G1 Preinfusion Group 1 Pre-Inf Group 1 Pre-Inf Preinfusion BY GROUP 0s Wet 0s Hold Exit page 65 page 66 page 66...
  • Page 32 “Technical” Programming La Marzocco 09:30 92.0°C page Press and hold the T3 button for 10 seconds. Enter Password ****** page 39 Technician Menu Press B3 to Exit Language Temp Units Name Group Dose ENGLISH CELSIUS LaMarzocco Settings page 74 page 76...
  • Page 33 “Technical” Programming Prop. Steam Backflush Chrono Chrono Info Type Settings INDIVIDUAL ENABLED DOSE page 95 page 99 page 102 page 104 Coffee Boiler Solenoid Test Scale Water Dose Settings Settings Configuration Settings page 115 page 112 page 108 page 105 Coffee Dose Electronics H20 Sensor - TDS...
  • Page 34 Programming Introduction Description • This espresso machine has a CPU and many configurable settings. • Additionally, there are many feedback controls employed in this espresso machine to troubleshoot problems should they occur. • The following is a brief introduction to the controls and display and how they interact with the operator. Digital Display Digital display 2nd group coffee boiler temperature...
  • Page 35 Programming Keypad The keypad has two functions. The first is for control of the espresso. The second is for programming individual software parameters. The programming of the individual parameters is possible only using the buttons in the group 1 (group starting from the left). Description Button This button is used to control the brewing of the single espresso.
  • Page 36 Start Up Procedures Description Turning the Espresso Machine On The following is the procedure for turning • Proceed checking for water connection on the power to the espresso machine. to the espresso machine. • Please follow the procedures carefully • Proceed making sure you have filled the to avoid any damage to the espresso boilers.
  • Page 37 Shut Down Procedures Description Turning the Espresso Machine Off The following is the procedure for turning • This machine has two off settings. One off power to the espresso machine. setting turns off all of the components • Please follow the procedures carefully in the espresso machine and the other to avoid any damage to the espresso turns off power to the complete espresso...
  • Page 38 Accessing Programming Mode Description Programming Mode • To change the values of any parameter • Barista Programming - The parameters the operator must first enter into the contained within this level are ones programming mode. the operator can change to affect the •...
  • Page 39 Accessing Programming Mode Description Programming Mode • Technical Programming - The parameters contained within this level are ones the operator can change to affect the performance of the espresso machine. 94.4 00:00 These parameters are set in the factory 95.5 95.1 their adjustment...
  • Page 40 Cleaning Cycles Description Cleaning Cycles • This parameter allows the operator • The rinsing procedure is provided to give to carry out the washing of the coffee the operator more flexibility and freedom groups, in an automatic way, by running with regard to this operation.
  • Page 41 Brewratio Programming (only on ABR espresso machine models) Description Brewratio The procedure for weighing the filter • To brew in brew ratio mode, set this holder either empty or filled with coffee mode by entering the software settings. powder is shown below. •...

  • Page 42: Group Dose Settings

    “Barista” Programming Description Program Dose • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. amount) each button •...
  • Page 43 “Barista” Programming Description Program Dose • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. amount) each button •...

  • Page 44: Group 1 Mode Pulses

    “Barista” Programming Description Program Dose • This parameter allows the operator to • It is possible to set the dose for both program the amount of coffee (brewing a short and a long shot on the same amount) for each Selection Indicator. Selection Indicator.
  • Page 45 “Barista” Programming Description Program Dose • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. amount) each button •...
  • Page 46 “Barista” Programming Description Program Dose • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. amount) each button •...
  • Page 47 “Barista” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key.
  • Page 48 “Barista” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key.
  • Page 49 “Barista” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the operator to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key.

  • Page 50: Copy Doses By Button

    “Barista” Programming Description Program Dose • This parameter allows the operator to copy the doses present of each key to the others. Group Dose Settings Copy Doses By Button Display Operating Procedure When the espresso machine is turned on, press and hold the T3 button to access the “Barista” programming. 94.4 00:00 After about 5 seconds the following screen is displayed.
  • Page 51 “Barista” Programming Description Program Dose • This parameter allows the operator to copy the doses present of each key to the others. Group Dose Settings Copy Doses By Button Display Operating Procedure Press the key where you want to paste the previously copied setting. Successful programming is indicated by Push to Paste the fixed lighting of the key.
  • Page 52 “Barista” Programming Description Program Dose • This parameter allows the operator to copy the doses present of each group to the others. Group Dose Settings Copy Doses By Group Display Operating Procedure When the espresso machine is turned on, press and hold the T3 button to access the “Barista” programming. 94.4 00:00 After about 5 seconds the following screen is displayed.
  • Page 53 “Barista” Programming Description Program Dose • This parameter allows the operator to copy the doses present of each group to the others. Group Dose Settings Copy Doses By Group Display Operating Procedure Press the key where you want to paste the previously copied setting. Successful programming is indicated by Push to Paste the fixed lighting of the key.
  • Page 54 “Barista” Programming Description Program Dose • This parameter allows the operator to cancel all the doses set. Group Dose Settings Reset Doses Display Operating Procedure When the espresso machine is turned on, press and hold the T3 button to access the “Barista” programming. 94.4 00:00 After about 5 seconds the following screen is displayed.
  • Page 55 “Barista” Programming Description Program Dose • This parameter allows the operator to cancel all the doses set. Group Dose Settings Reset Doses Display Operating Procedure Press T1 or T2 to continue with the programming of the other parameters. Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the espresso 94.4 00:00 machine.
  • Page 56 “Barista” Programming Description Program Dose • This parameter enables the operator to check of the flowmeter. Group Dose Settings Flowmeter Test Display Operating Procedure When the espresso machine is turned on, press and hold the T3 button to access the “Barista” programming. 94.4 00:00 After about 5 seconds the following screen is displayed.

  • Page 57: Backflush Individual

    “Barista” Programming Description Backflush • This parameter allows the operator • Do not perform the cleaning procedure to carry out the washing of the coffee when other groups are dispensing groups, in an automatic way, by running coffee. Group Dose multiple cleaning cycles.
  • Page 58 “Barista” Programming Description Backflush • This parameter allows the operator • Do not perform the cleaning procedure to carry out the washing of the coffee when other groups are dispensing groups, in an automatic way, by running coffee. Group Dose multiple cleaning cycles.
  • Page 59 “Barista” Programming Description Backflush • This parameter allows the operator • Do not perform the cleaning procedure to carry out the washing of the coffee when other groups are dispensing groups, in an automatic way, by running coffee. Group Dose multiple cleaning cycles.

  • Page 60: Water Dose Enabled

    “Barista” Programming Description Water Dose • This parameter allows the operator to • This feature can be enabled or disabled. program the amount of water (brewing amount) for the hot water button. Group Dose Settings Water Dose Settings Display Operating Procedure When the espresso machine is turned on, press and hold the T3 button to access the “Barista”...
  • Page 61 “Barista” Programming Description Water Dose • This parameter allows the operator to • This feature can be enabled or disabled. program the amount of water (brewing amount) for the hot water button. Group Dose Settings Water Dose Settings Display Operating Procedure Desired dose can be programmed using hot water button.
  • Page 62 “Barista” Programming Description Water Dose • This parameter allows the operator to • This feature can be enabled or disabled. program the amount of water (brewing amount) for the hot water button. Group Dose Settings Water Dose Settings Display Operating Procedure Water Dose Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Barista”...

  • Page 63: Enabled

    “Barista” Programming Description Coffee Boiler • This parameter allows the operator to • This parameter allows the operator to enable/disable the coffee boiler. program the coffee boiler temperature. Each group can have a different Group Dose programming. Settings Coffee Boiler Settings Display Operating Procedure...

  • Page 64: Cb1 Temperature

    “Barista” Programming Description Coffee Boiler • This parameter allows the operator to • This parameter allows the operator to enable/disable the coffee boiler. program the coffee boiler temperature. Each group can have a different Group Dose programming. Settings Coffee Boiler Settings Display Operating Procedure...
  • Page 65 “Barista” Programming Description Pre-Infusion or Pre-Brewing • This parameter allows the operator to pre-brewing cycle; during this time the program the time of pre-brewing of pump is active. Once the pre-brewing water with the coffee. Each group can cycle is over, the normal brewing cycle Group Dose have a different programming.
  • Page 66 “Barista” Programming Description Pre-Infusion or Pre-Brewing • This parameter allows the operator to pre-brewing cycle; during this time the program the time of pre-brewing of pump is active. Once the pre-brewing water with the coffee. Each group can cycle is over, the normal brewing cycle Group Dose have a different programming.
  • Page 67 “Barista” Programming Description Cup Warmer • This parameter allows the operator to • This function is displayed only on the enable or disable the cups heating models of espresso machine equipped function. with this accessory. Group Dose Settings Cup Warmer ENABLED Display Operating Procedure...
  • Page 68 “Barista” Programming Description Cup Warmer • This parameter allows the operator to • This function is displayed only on the enable or disable the cups heating models of espresso machine equipped function. with this accessory. Group Dose Settings Cup Warmer ENABLED Display Operating Procedure...
  • Page 69 “Barista” Programming Description Water Quality • This parameter allows the operator to view the TDS and water hardness values that are measured by the water probe at Group Dose the inlet of the coffee machine. Settings H20 Sensor - TDS 000.0 ppm Display Operating Procedure...
  • Page 70 “Barista” Programming Description Water Quality • This parameter allows the operator to view the TDS and water hardness values that are measured by the water probe at Group Dose the inlet of the coffee machine. Settings Total Hardness 000.0 ppm Display Operating Procedure When the espresso machine is turned on, press and hold the T3 button to access the “Barista”...
  • Page 71 “Barista” Programming Description Gateway • This parameter allows the operator to connect the coffee machine to the WiFi connection. Group Dose Settings Configure Gateway Display Operating Procedure When the espresso machine is turned on, press and hold the T3 button to access the “Barista” programming. 94.4 00:00 After about 5 seconds the following screen is displayed.
  • Page 72 “Barista” Programming Description Gateway • This parameter allows the operator to connect the coffee machine to the WiFi connection. Group Dose Settings Configure Gateway Display Operating Procedure Press T1 or T2 to continue with the programming of the other parameters. Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the espresso 94.4 00:00...

  • Page 73: Press B3 To Exit

    “Barista” Programming Description Exit Menu • This parameter allows the operator to exit the “Barista” programming and return to the normal use of the espresso Group Dose machine. Settings Menu Press B3 to Exit Display Operating Procedure Press the T3 button to exit the “Barista” programming and return to the normal use of the espresso Menu machine.

  • Page 74: Language English

    “Technical” Programming Description Language • This parameter allows the technician to change the language of the display. Enter Password ****** Language ENGLISH Display Operating Procedure When the espresso machine is turned on, press and hold the T3 button. After about 10 seconds the following 94.4 00:00 screen is displayed.
  • Page 75 “Technical” Programming Description Language • This parameter allows the technician to change the language of the display. Enter Password ****** Language ENGLISH Display Operating Procedure To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is displayed. Menu Press the T3 button to exit the menu and return to the normal use of the espresso machine.

  • Page 76: Temp Units Celsius

    “Technical” Programming Description Temperature Measurement Units • This parameter allows the technician to change the temperature display from degrees Celsius to degrees Fahrenheit Enter Password and vice versa. ****** Temp Units CELSIUS Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 77 “Technical” Programming Description Temperature Measurement Units • This parameter allows the technician to change the temperature display from degrees Celsius to degrees Fahrenheit Enter Password and vice versa. ****** Temp Units CELSIUS Display Operating Procedure Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine 94.4 00:00 by pressing T2 and T3 at the same time.

  • Page 78: Name

    “Technical” Programming Description Name • This parameter allows the technician to • The user name is displayed continuously program a 16 character user name. on the display on the second line. Enter Password ****** Name LaMarzocco Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 79 “Technical” Programming Description Name • This parameter allows the technician to • The user name is displayed continuously program a 16 character user name. on the display on the second line. Enter Password ****** Name LaMarzocco Display Operating Procedure Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine 94.4 00:00 by pressing T2 and T3 at the same time.
  • Page 80 “Technical” Programming Description Program Dose • This parameter allows the operator to • It is possible to set the dose for both program the amount of coffee (brewing a short and a long shot on the same amount) for each Selection Indicator. Selection Indicator.
  • Page 81 “Technical” Programming Description Program Dose • This parameter allows the operator to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. amount) each button •...
  • Page 82 “Technical” Programming Description Program Dose • This parameter allows the technician to • It is possible to set the dose for both program the amount of coffee (brewing a short and a long shot on the same amount) for each Selection Indicator. Selection Indicator.
  • Page 83 “Technical” Programming Description Program Dose • This parameter allows the technician to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. amount) each button •...
  • Page 84 “Technical” Programming Description Program Dose • This parameter allows the technician to • It is possible to set the dose for both a program the amount of coffee (brewing short and a long shot on the same key. amount) each button •...
  • Page 85 “Technical” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the technician to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key.
  • Page 86 “Technical” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the technician to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key.
  • Page 87 “Technical” Programming (only on ABR espresso machine models) Description Program Dose Scales • This parameter allows the technician to • For greater accuracy and consistency of view and manually change each dose for the doses, it is recommended that you each key.
  • Page 88 “Technical” Programming (only on ABR espresso machine models) Description Program Dose • This parameter allows the technician to copy the doses present of each key to the others. Group Dose Settings Copy Doses By Button Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 89 “Technical” Programming (only on ABR espresso machine models) Description Program Dose • This parameter allows the technician to copy the doses present of each key to the others. Group Dose Settings Copy Doses By Button Display Operating Procedure Press the key where you want to paste the previously copied setting. Successful programming is indicated by Push to Paste the fixed lighting of the key.
  • Page 90 “Technical” Programming Description Program Dose • This parameter allows the technician to copy the doses present of each group to the others. Group Dose Settings Copy Doses By Group Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 91 “Technical” Programming Description Program Dose • This parameter allows the technician to copy the doses present of each group to the others. Group Dose Settings Copy Doses By Group Display Operating Procedure Press the key where you want to paste the previously copied setting. Successful programming is indicated by Push to Paste the fixed lighting of the key.
  • Page 92 “Technical” Programming Description Program Dose • This parameter allows the technician to cancel all the doses set. Group Dose Settings Reset Doses Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 93 “Technical” Programming Description Program Dose • This parameter allows the technician to cancel all the doses set. Group Dose Settings Reset Doses Display Operating Procedure Press T1 or T2 to continue with the programming of the other parameters. Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the espresso 94.4 00:00 machine.
  • Page 94 “Technical” Programming Description Program Dose • This parameter enables the technician to check of the flowmeter. Group Dose Settings Flowmeter Test Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 94.4 00:00 until the following screen is displayed.
  • Page 95 “Technical” Programming Description Prop. Steam • This parameter allows the technician to calibrate the potentiometer, adjusting the steam delivery starting and end Enter Password point. ****** Prop. Steam Settings Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 96 “Technical” Programming Description Prop. Steam • This parameter allows the technician to calibrate the potentiometer, adjusting the steam delivery starting and end Enter Password point. ****** Prop. Steam Settings Display Operating Procedure Raise L Steam Operate the left-hand steam lever, fully raising it, then press the T3 button. &...
  • Page 97 “Technical” Programming Description Prop. Steam • This parameter allows the technician to calibrate the potentiometer, adjusting the steam delivery starting and end Enter Password point. ****** Prop. Steam Settings Display Operating Procedure Test Steam Pot To check the correct operation of the mechanical potentiometer, operate the left and right steam levers. Left: 52% 2.7V Right: 30% 1.7V Prop.
  • Page 98 “Technical” Programming Description Prop. Steam • This parameter allows the technician to calibrate the potentiometer, adjusting the steam delivery starting and end Enter Password point. ****** Prop. Steam Settings Display Operating Procedure Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine 94.4 00:00 by pressing T2 and T3 at the same time.
  • Page 99 “Technical” Programming Description Backflush • This parameter allows the operator • Do not perform the cleaning procedure to carry out the washing of the coffee when other groups are dispensing groups, in an automatic way, by running coffee. Enter Password multiple cleaning cycles.
  • Page 100 “Technical” Programming Description Backflush • This parameter allows the operator • Do not perform the cleaning procedure to carry out the washing of the coffee when other groups are dispensing groups, in an automatic way, by running coffee. Enter Password multiple cleaning cycles.
  • Page 101 “Technical” Programming Description Backflush • This parameter allows the operator • Do not perform the cleaning procedure to carry out the washing of the coffee when other groups are dispensing groups, in an automatic way, by running coffee. Enter Password multiple cleaning cycles.
  • Page 102 “Technical” Programming Description Crono Function • When enabled, this parameter displays a • If enabled, the Chrono function is timer that times each shot. permanently displayed during brewing, • The timer is reset each time a button on while during wait state it alternates with Enter Password the keypad is pressed.
  • Page 103 “Technical” Programming Description Crono Function • When enabled, this parameter displays a • If enabled, the Chrono function is timer that times each shot. permanently displayed during brewing, • The timer is reset each time a button on while during wait state it alternates with Enter Password the keypad is pressed.
  • Page 104 “Technical” Programming Description Crono Function • When enabled, this parameter displays a • If enabled, the Chrono function is timer that times each shot. permanently displayed during brewing, • The timer is reset each time a button on while during wait state it alternates with Enter Password the keypad is pressed.
  • Page 105 “Technical” Programming Description Water Dose • This parameter allows the operator to • This feature can be enabled or disabled. program the amount of water (brewing amount) for the hot water button. Enter Password ****** Water Dose Settings Display Operating Procedure After accessing the “Technical”...
  • Page 106 “Technical” Programming Description Water Dose • This parameter allows the operator to • This feature can be enabled or disabled. program the amount of water (brewing amount) for the hot water button. Enter Password ****** Water Dose Settings Display Operating Procedure Desired dose can be programmed using hot water button.
  • Page 107 “Technical” Programming Description Water Dose • This parameter allows the operator to • This feature can be enabled or disabled. program the amount of water (brewing amount) for the hot water button. Enter Password ****** Water Dose Settings Display Operating Procedure Water Dose Press the T3 button to return to the “Technical”...
  • Page 108 “Technical” Programming (only on ABR espresso machine models) Description Program Scales • This parameter enables the technician to set some scale parameters like: Enabling/disabling offset Enter Password parameter; ****** - Setting the weight reading time; - Calibrating the scales; Scale - Updating the scale software.
  • Page 109 “Technical” Programming (only on ABR espresso machine models) Description Program Scales • This parameter enables the technician to set some scale parameters like: Enabling/disabling offset Enter Password parameter; ****** - Setting the weight reading time; - Calibrating the scales; Scale - Updating the scale software.
  • Page 110 “Technical” Programming (only on ABR espresso machine models) Description Program Scales • This parameter enables the technician to set some scale parameters like: Enabling/disabling offset Enter Password parameter; ****** - Setting the weight reading time; - Calibrating the scales; Scale - Updating the scale software.
  • Page 111 “Technical” Programming (only on ABR espresso machine models) Description Program Scales • This parameter enables the technician to set some scale parameters like: Enabling/disabling offset Enter Password parameter; ****** - Setting the weight reading time; - Calibrating the scales; Scale - Updating the scale software.
  • Page 112 “Technical” Programming Description Solenoid Test • This parameter allows the technician to verify the proper work of all solenoid valves. Enter Password ****** Solenoid Test Settings Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 113 “Technical” Programming Description Solenoid Test • This parameter allows the technician to verify the proper work of all solenoid valves. Enter Password ****** Solenoid Test Settings Display Operating Procedure Test Hot Water Solenoid Press the T3 button to start verifying the proper work of hot water solenoid valve. Testing Solenoid ...
  • Page 114 “Technical” Programming Description Solenoid Test • This parameter allows the technician to verify the proper work of all solenoid valves. Enter Password ****** Solenoid Test Settings Display Operating Procedure Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Technical” Solenoid Test programming.
  • Page 115 “Technical” Programming Description though the temperature of the boiler Coffee Boiler may vary slightly, the temperature of the • This parameter enables the technician water exiting the group is constant. to set various parameters of the coffee • To properly calibrate the temperature boiler.
  • Page 116 “Technical” Programming Description Coffee Boiler • The OFFSET parameter is used to can cause unexpected results. calibrate the coffee boiler temperature • It is important to write down this value system to ensure the display temperature before making changes to be sure you Enter Password accurately represents the temperature can return to the factory programming if...
  • Page 117 “Technical” Programming Description Coffee Boiler • The OFFSET parameter is used to can cause unexpected results. calibrate the coffee boiler temperature • It is important to write down this value system to ensure the display temperature before making changes to be sure you Enter Password accurately represents the temperature can return to the factory programming if...
  • Page 118 “Technical” Programming Description Steam Boiler • This parameter enables the technician Temperature Pressure to set various parameters of the steam 247°F/119°C 1.0 bar boiler. Enter Password • The temperature of saturated water is 260°F/127°C 1.5 bar ****** proportional to the pressure inside the Steam Boiler.
  • Page 119 “Technical” Programming Description Steam Boiler • The parameter filling WITH PUMP allows process can reduce the overall dispens- the technician to select the activation ing pressure in the brew boiler. of the water pump during the automatic • During the auto-fill cycle, if a brew Enter Password filling cycle of the service boiler.
  • Page 120 “Technical” Programming Description Steam Boiler valve has triggered disable the function. boiler, discharging about one half of the • Should the safety valve fail to trigger water contained in the boiler. within approximately one minute of the • This procedure is recommended in case Enter Password temperature reaching 140°C, disable the machine should remain inactive for...
  • Page 121 “Technical” Programming Description Steam Boiler Enter Password ****** Steam Boiler Settings Display Operating Procedure Press Water Button Press the hot water button to start draining the water contained in the steam boiler. Press the T3 button when Enter when Empty the boiler is empty, wait for refilling completion.
  • Page 122 “Technical” Programming Description Steam Boiler Enter Password ****** Steam Boiler Settings Display Operating Procedure To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is displayed. Menu Press the T3 button to exit the menu and return to the normal use of the espresso machine. Press B3 to Exit Alternatively, you can exit the “Technical”...
  • Page 123 “Technical” Programming Description Steam Boiler • The parameter “Level Sensit.” allows the • The black connection cable corresponds technician to select the probe sensitivity to the working level probe. for steam boiler filling according to water • The red connection cable corresponds to Enter Password hardness.
  • Page 124 “Technical” Programming Description Steam Boiler • The parameter “Level Sensit.” allows the • The black connection cable corresponds technician to select the probe sensitivity to the working level probe. for steam boiler filling according to water • The red connection cable corresponds to Enter Password hardness.
  • Page 125 “Technical” Programming Description Pre-Infusion or Pre-Brewing • This parameter allows the operator to pre-brewing cycle; during this time the program the time of pre-brewing of pump is active. Once the pre-brewing water with the coffee. Each group can cycle is over, the normal brewing cycle Enter Password have a different programming.
  • Page 126 “Technical” Programming Description Pre-Infusion or Pre-Brewing • This parameter allows the operator to pre-brewing cycle; during this time the program the time of pre-brewing of pump is active. Once the pre-brewing water with the coffee. Each group can cycle is over, the normal brewing cycle Enter Password have a different programming.
  • Page 127 “Technical” Programming Description Cup Warmer • This parameter allows the technician • This parameter allows the technician to to enable or disable the cups heating select the operating of the cup warmer function. by time or by button on the control Enter Password •...
  • Page 128 “Technical” Programming Description Cup Warmer • This parameter allows the technician • This parameter allows the technician to to enable or disable the cups heating select the operating of the cup warmer function. by time or by button on the control Enter Password •...

  • Page 129: Auto On/Off Settings

    “Technical” Programming Description Auto ON/OFF • This parameter allows the technician to • This feature also allows the espresso program the espresso machine to turn on machine to remain in the off condition at a preset time and turn off at a preset for one repeating closed day.
  • Page 130 “Technical” Programming Description Auto ON/OFF • This parameter allows the technician to • This feature also allows the espresso program the espresso machine to turn on machine to remain in the off condition at a preset time and turn off at a preset for one repeating closed day.
  • Page 131 “Technical” Programming Description Auto ON/OFF • This parameter allows the technician to • This feature also allows the espresso program the espresso machine to turn on machine to remain in the off condition at a preset time and turn off at a preset for one repeating closed day.

  • Page 132: Current Date 19 July 2021

    “Technical” Programming Description Calendar • This parameter allows the user to set the day, month and year. Enter Password ****** Current Date 19 JULY 2021 Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 133 “Technical” Programming Description Clock Adjust • This parameter allows the user to set the • There are 4 changeable values within time of day and the day of the week. this parameter: • This parameter is used to display time •...
  • Page 134 “Technical” Programming Description Clock Adjust • This parameter allows the user to set the • There are 4 changeable values within time of day and the day of the week. this parameter: • This parameter is used to display time •...
  • Page 135 “Technical” Programming Description ECO Mode • This parameter allows the technician to • It is possible to set this parameter also set up a temperature to be maintained during the normal operation of the in case of a temporary non utilization of machine by pressing T1 and T2 at the Enter Password the espresso machine.
  • Page 136 “Technical” Programming Description ECO Mode • This parameter allows the technician to • It is possible to set this parameter also set up a temperature to be maintained during the normal operation of the in case of a temporary non utilization of machine by pressing T1 and T2 at the Enter Password the espresso machine.

  • Page 137: Filter Alarm Settings

    “Technical” Programming Description Filter Alarm • This parameter enables the technician • A value of 0 (zero) disables the filter to program an alarm that will alert the alarm parameter. user about the need for maintenance or • This feature can be enabled or disabled. Enter Password replacement of the water filter.
  • Page 138 “Technical” Programming Description Filter Alarm • This parameter enables the technician • A value of 0 (zero) disables the filter to program an alarm that will alert the alarm parameter. user about the need for maintenance or • This feature can be enabled or disabled. Enter Password replacement of the water filter.
  • Page 139 “Technical” Programming Description Filter Alarm • This parameter enables the technician • A value of 0 (zero) disables the filter to program an alarm that will alert the alarm parameter. user about the need for maintenance or • This feature can be enabled or disabled. Enter Password replacement of the water filter.
  • Page 140 “Technical” Programming Description Dose Counter • This parameter allows the technician • This parameter displays different values: to review the total doses dispensed for • Total steaming doses; each button. • Total purges doses; Enter Password • Total small doses; ****** •...
  • Page 141 “Technical” Programming Description Coffee Dose Counter • This parameter allows the technician • This parameter displays different values: to review the total doses dispensed for • Total coffee doses; each button. • Coffee doses for each button; Enter Password • Hot water doses.
  • Page 142 “Technical” Programming Description Coffee Dose Counter • This parameter allows the technician • This parameter displays different values: to review the total doses dispensed for • Total coffee doses; each button. • Coffee doses for each button; Enter Password • Hot water doses.
  • Page 143 “Technical” Programming Description Electronics • This parameter allows the technician to display the hardware and firmware version for all the electronic boards Enter Password installed on the espresso machine. ****** Electronics Settings Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 144 “Technical” Programming Description Electronics • This parameter allows the technician to display the hardware and firmware version for all the electronic boards Enter Password installed on the espresso machine. ****** Electronics Settings Display Operating Procedure 24V Universal Using the buttons T1 and T2 to display the hardware and firmware version for the Universal Board. HW0 FW0.6.0 G1 Scale Using the buttons T1 and T2 to display the hardware and firmware version for the Scale.
  • Page 145 “Technical” Programming Description Electronics • This parameter allows the technician to display the hardware and firmware version for all the electronic boards Enter Password installed on the espresso machine. ****** Electronics Settings Display Operating Procedure Press T1 or T2 to continue with the programming of the other parameters. To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is displayed.
  • Page 146 “Technical” Programming Description Water Quality • This parameter allows the operator to view the TDS and water hardness values that are measured by the water probe at Enter Password the inlet of the coffee machine. ****** H20 Sensor - TDS 000.0 ppm Display Operating Procedure...
  • Page 147 “Technical” Programming Description Water Quality • This parameter allows the operator to view the TDS and water hardness values that are measured by the water probe at Enter Password the inlet of the coffee machine. ****** Total Hardness 000.0 ppm Display Operating Procedure After accessing the “Technical”...
  • Page 148 “Technical” Programming Description Gateway • This parameter allows the operator to connect the coffee machine to the WiFi connection. Enter Password ****** Configure Gateway Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 149 “Technical” Programming Description Save and Load USB • This parameter allows the technician to load some guide profiles from the USB pendrive. Enter Password ****** Save and Load USB Settings Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 150 “Technical” Programming Description Save and Load USB • This parameter allows the technician to load some guide profiles from the USB pendrive. Enter Password ****** Save and Load USB Settings Display Operating Procedure Settings Confirmation message: all settings have been successfully loaded. Successfully Loaded Save Barista Press the T3 button to enter the menu.
  • Page 151 “Technical” Programming Description Save and Load USB • This parameter allows the technician to load some guide profiles from the USB pendrive. Enter Password ****** Save and Load USB Settings Display Operating Procedure Save Technician Press the T3 button to enter the menu. Settings to USB Insert USB Key Enter to Exit...
  • Page 152 “Technical” Programming Description Save and Load USB • This parameter allows the technician to load some guide profiles from the USB pendrive. Enter Password ****** Save and Load USB Settings Display Operating Procedure Press T1 or T2 to continue with the programming of the other parameters. To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is displayed.
  • Page 153 “Technical” Programming Description Reset • This parameter allows the technician to • It is possible to reset the settings you reset all the values returning to initial made in the “Barista” programming or factory settings. the settings you made in the “Technical” Enter Password programming.
  • Page 154 “Technical” Programming Description Reset • This parameter allows the technician to • It is possible to reset the settings you reset all the values returning to initial made in the “Barista” programming or factory settings. the settings you made in the “Technical” Enter Password programming.

  • Page 155: First Startup Enabled

    “Technical” Programming Description First Startup • This parameter allows the technician to enable/disable first startup procedure. Enter Password ****** First Startup ENABLED Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 156 “Technical” Programming Description Update Firmware • This parameter allows the technician to update the control unit of the espresso machine via a USB Pendrive. Enter Password ****** Update Firmware Display Operating Procedure After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2 Enter Password until the following screen is displayed.
  • Page 157 “Technical” Programming Description Exit Menu • This parameter allows the technician to exit the “Technical” programming and return to the normal use of the espresso Enter Password machine. ****** Menu Press B3 to Exit Display Operating Procedure Menu Press the T3 button to exit the “Technical” programming and return to the normal use of the espresso machine. Press B3 to Exit...

Table of Contents