Table Of Contents Getting Started ............3 Device Overview ............4 Device indicator display ...........5 Installing the SIM Card ..........7 Removing the SIM Card ..........8 Charging the Battery ..........8 Logging into Device Management Website...9 Setting up Wi-Fi connection.........10 Setting up your WPS ..........11 How to change the SSID &...
Getting Started Thank you for choosing the Orbic SPEED 2® Hotspot. The device’s 5G capabilities offer a secure reliable Wi-Fi connection whether you are working from home or traveling. This guide provides the basic operations of your mobile hotspot.
Device Overview Power/WPS button Signal status and Network mode indicator 5G indicator Wi-Fi indicator Battery indicator SIM slot USB Type-C port Hard reset Note: The battery is non-removable.
Device indicator display Indicator Status Registered to 5G/4G network of strong signal: Green Steady Registered to 5G/4G network of weak signal: Orange Steady Not registered to any network: Off Registered to 5G network: Green Steady only registered to 4G network: Wi-Fi on: Green Steady Wi-Fi Wi-Fi Off: Light off...
Page 6
Battery indicator (in red and green): Battery >=20%, Green Steady Battery <20%, Red Steady Battery When charging: Battery>=20%, Green Blinking Battery < 20%, Red Blinking Power charge completed: Green Steady...
Installing the SIM Card Follow the instructions below to install the SIM card: Press the card needle to make the SIM card tray pop out. 2. Put the SIM card on the SIM card tray. 3. Insert the SIM card into the slot. Note: Do not bend or scratch your SIM card, and avoid exposing the SIM card to static electricity, water or dirt.
Removing the SIM Card Ensure the device is powered off and open the SIM card cover. 2. Gently remove the SIM card from the SIM card slot and close the SIM card cover. Charging the Battery Your device comes with a charger. To charge, plug one end of the charger into an electrical outlet and the other end into the device’s USB Type-C Port.
Logging into the Device Management website Make sure your device is connected to the hotspot via Wi-Fi or USB Type-C cable. 2. Open the browser, and input http://192.168.1.1 http:// my.OrbicSpeed/ in the address bar. 3. Enter username and password, and click Login.
Your Wi-Fi SSID and password can be found on the device label. Note: for more information on using the WEB interface on the SPEED 2 5G, please download the user manual from the Orbic.us support...
Wi-Fi > WPS. 2. Click Connect button to activate the WPS function. 3. Enable the WPS function on the device being connected to the Orbic Speed 2 -OR- Through WPS button: Double-click the Power/WPS button to activate the WPS function.
Short press the Power/WPS button, you will exit the WPS function. How to change the SSID & Password You can change the SSID & Password through WebUI. Make sure to connect your device (tablet, PC, etc) to the hotspot via Wi-Fi or USB cable.
Restore Factory Settings If you are uncertain of which Wi-Fi settings you the factory defaults that come with the device Log in to the WebUI and click the Reset button under the Management. Reboot & Reset to restore your hotspot to its factory default settings.
Q&A Q: What do I do if I see the SSID but failed to connect? Check if the password you entered is the correct one. 2. Check if WPS security is enabled on your PC. If so, please check if the device is performing WPS operations.
Page 15
the Wi-Fi > Wi-Fi Basic Settings section on the WebUI. 2. You can also reset the device to factory defaults. The default password is listed on the device label on the back of the device. Q: What if my SIM card gets locked out? If the SIM card is locked, log in to the WebUI (http://192.168.1.1 or http://my.OrbicSpeed/) and input the PIN or PUK code you received from...
Safety • Some electronic devices, such as the electronic system of vehicles, are susceptible to electromagnetic interference sent by your device if inadequately shielded. Please consult the manufacturer of your device before using if necessary. • Operating your device may interfere with medical devices like hearing aids and pacemakers.
Page 17
stations, and in hospitals. Please observe and obey all warning signs and power off your device in these conditions. • Do not touch the inner antenna area if not necessary; it will affect your device’s performance. • Store your device out of the reach of little children.
Using Your Device • Please use original accessories or accessories that are authorised. Using any unauthorised accessories may affect your device’s performance, and violate related national regulations about telecom terminals. • Avoid using your device near or inside metallic structures or establishments that can emit electromagnetic waves;...
5% - 95% are recommended. CE Declaration of conformity Hereby, Orbic North America LLC declares that this 5G Mobile Wi-Fi, SPEED 2® 5G Hotspot is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/...
This product should not be treated as household waste, instead it should be handed over to the applicable. CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. SAR Information Statement Your product is tested to comply with applicable requirements and regulations of the European Union of human exposure to radio wave.
5GHz Wi-Fi Notice (Europe and Japan) The Wi-Fi funtion for Orbic SPEED 2 5G Mobile Hotspot is restricted to indoor use only when operating in the 5150 MHz to 5350 MHz frequency range.
Frequency Bands and Power Frequency bands in which the radio equipment operates: Some bands may not be available in all countries or all areas. Please contact the local carrier for more details: FDD : B1/B3/B5/B7/B8/B18/B19/B20/B26/B28: 23 dBm±1.5 TDD: B38/B40/B41/B42/B43: 23dBm±1.5 5G NR N1/N3/N5/N7/N8/N20/N26/N28/N38/ N41/N77: 23dBm±1.5 5G NR N40/N78/N79: 26 dBm±1.5...
Page 23
5250-5350 MHz 5470-5725 MHz UK(NI) EU Regulatory Compliance - Orbic North America LLC declares that Orbic SPEED 2® 5G Hotspot is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit www.orbic.us...
Collection Business Center Dreischeibenhaus D-40211 Düsseldorf Model Code : O5sH13 Model Name : Orbic SPEED 2® 5G Hotspot Support and More For how to use, or more tips and tricks on getting the most out of your new Orbic SPEED 2® 5G Hotspot, check out the guides and more information at - www.orbic.us...
Need help?
Do you have a question about the SPEED 2 and is the answer not in the manual?
Questions and answers