Download Print this page

D-Link DES-1105 User Manual

5-port switch
Hide thumbs




  Related Manuals for D-Link DES-1105

  Summary of Contents for D-Link DES-1105

  • Page 2: Table Of Contents

    Front Panel (LEDs) ... 8 Rear Panel (Connections)... 9 Installation... 10 Connecting the Switch ... 10 PC to DES-1105 ... 10 Hub/Switch to DES-1105 ... 10 DES-1105 to Other Devices... 10 Port Speed & Duplex Mode ... 11 Mounting the Switch on the Wall... 12 Mounting on a cement wall ...
  • Page 3: Product Overview

    • Visually inspect the DC power jack and make sure that it is fully secured to the power adapter. • Do not cover the ventilation holes on the sides of the Switch, and make sure there is adequate ventilation around it.
  • Page 4: Introduction

    A switch is a viable solution even if demanding applications, such as multimedia production and video conferencing, are on the horizon.The most promising techniques,...
  • Page 5 For Ethernet networks, a switch is an effective way of eliminating the problem of chaining hubs beyond the “two-repeater limit.” A switch can be used to split parts of the network into different collision domains, making it possible to expand your Ethernet network beyond the 205-meter network diameter limit for 100BASE-TX networks.
  • Page 6: Features

    200Mbps, any one of its five ports may be used to cascade to an additional switch to open a Full-Duplex Fast Ethernet pipe. • The DES-1105 is the perfect choice for a department or office planning to upgrade to Fast Ethernet. The DES-1105 can accommodate 10Mbps or 100Mbps devices, providing a flexible solution for existing (10Mbps) Ethernet workgroups.
  • Page 7 • Flow control for any port. This minimizes dropped packets by sending out collision signals when the port’s receiving buffer is full. • Data filtering rate eliminates all error packets, runts, etc., per port at wire-speed for 100Mbps operation and 10Mbps operation. D-Link DES-1105 User Manual...
  • Page 8: Hardware Overview

    Front Panel (LEDs) Power: This green indicator light is on when the DES-1105 is receiving power; otherwise, it is off. Link/Activity (1-5): This LED indicator light is green when the port is connected to a 100Mbps Fast Ethernet station. The green indicator blinks as Ethernet data is transmitted or received.
  • Page 9: Rear Panel (Connections)

    Power is supplied through an external DC power adapter. Check the technical specification section for information about the DC power input voltage. Since the DES-1105 does not require a power button, plugging its power adapter into a power outlet will immediately power it on.
  • Page 10: Installation

    Hub/Switch to DES-1105 A hub (10 or 100BASE-TX) can be connected to the DES-1105 via a two-pair Category 3, 4, or 5 UTP/STP Straight- Through or Crossover cable. For 100Mbps operation a Category 5 cable must be used. The connection is accomplished from any port of the hub to any port of the DES-1105.
  • Page 11: Port Speed & Duplex Mode

    (10Mbps or 100Mbps) for any new twisted-pair connection. If the attached device does not support auto-negotiation or has auto-negotiation disabled, an auto-sensing process is initiated to select the speed and half-duplex mode is selected. D-Link DES-1105 User Manual...
  • Page 12: Mounting The Switch On The Wall

    Mounting the Switch on the Wall The DES-1105 can also be mounted on a wall. Two mounting slots are provided on the bottom of the switch for this purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the illustration below: 1.
  • Page 13: Troubleshooting

    Crossover) and adjust themselves accordingly to pass data over the network. 3. What is the maximum length of Category 3, 4 or 5 twisted pair cable that can be used between the DES-1105 and other devices such as routers, switches, computers, etc.? The maximum length of Category 3, 4 or 5 twisted pair cable that can be used between computers and other devices on a network is 100 meters or about 328 feet.
  • Page 14: Networking Basics

    Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.
  • Page 15: Statically Assign An Ip Address

    2000 - From the desktop, right-click My Network Places > Properties. ® Step 2 Right-click on the Local Area Connection which represents your D-Link network adapter and select Properties. Step 3 Highlight Internet Protocol (TCP/IP) and click Properties. Step 4 Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router.
  • Page 16: Technical Specifications

    Operating: 0° ~ 40° C (32º to 104º F) Storage: -10° ~ 70° C (14ºto 158º F) Humidity Operating: 10% ~ 90% RH, Non-condensing Storage: 5% ~ 90% RH, Non-condensing D-Link DES-1105 User Manual DES-1105 Specifications 10Mbps (half duplex) 20Mbps (full-duplex) 100Mbps (half duplex) 200Mbps (full- duplex) 2-pair UTP Cat.
  • Page 17: Rj-45 Pin Specifications

    The following table shows the standard RJ-45 receptacle/connector and their pin assignments. RJ-45 Connector pin assignment Contact Media Direct Interface Signal D-Link DES-1105 User Manual (approx.) 147.5* 113* 31.5 mm (5.81* 4.45* 1.24 inch) FCC Class B, CE Class B Store-and-forward...
  • Page 18: Contacting Technical Support

    Contacting Technical Support D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our web site or by phone.
  • Page 19: Warranty

    Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement hardware need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware.
  • Page 20 Warranty Period and is subject to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by D-Link;...
  • Page 21 • The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 17595 Mt.
  • Page 22: Limitation Of Liability

    This Limited Warranty provides specific legal rights and you may also have other rights which vary from state to state. Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective owners.
  • Page 23: Fcc Statement

    • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D- Link office. D-Link DES-1105 User Manual...
  • Page 24: Registration

    Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. D-Link DES-1105 User Manual Registration Version 1.0 11/22/2005...