PCB Piezotronics 102M80A Installation And Operating Manual page 8

Model Number
102M 80A
Performance
Measurement Range(for ±5V output)
Useful Overrange(for ± 10V output)
Sensitivity(± 15 %)
Maximum Pressure(Total)
Maximum Pressure(step)
Resolution
Resonant Frequency
Rise Time(Reflected)
Non-Linearity
Environmental
Acceleration Sensitivity
Temperature Range(Operating)
Temperature Coefficient of Sensitivity
Maximum Flash Temperature
Maximum Vibration
Maximum Shock
Electrical
Discharge Time Constant(at room temp)
Excitation Voltage
Constant Current Excitation
Output Impedance
Output Bias Voltage
Physical
Housing Material 304L/316L Stainless Steel
Thread Adaptor Material
Diaphragm 316L Stainless Steel
Sealing
Electrical Connector 10-32 Coaxial Jack
Weight
[6]
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
®
ICP is a registered trademark of PCB Piezotronics, Inc.
ICP® PRESSURE SENSOR
EN GLISH SI
100 psi 689.5 kPa
200 psi 1,379 kPa
50 mV/psi 7.25 mV/kPa
7.5 kpsi 51,711 kPa
1,000 psi 6,900 kPa
2 mpsi 0.014 kPa
≥ 250 kHz ≥ 250 kHz
≤ 2.0 µ sec ≤ 2.0 µ sec
≤ 1.0 % FS ≤ 1.0 % FS
0.002 psi/g 0.0014 kPa/(m/s²)
-320 to 212 °F -196 to 100 °C
≤ 0.06 %/°F ≤ 0.108 %/°C
3,000 °F 1648.89 °C
2,000 g pk 19,600 m/s² pk
20,000 g pk 196,000 m/s² pk
≥ 1.0 sec ≥ 1.0 sec
15 to 30 VDC 15 to 30 VDC
2 to 20 mA 2 to 20 mA
100 Ohm 100 Ohm
3 to 8 VDC 3 to 8 VDC
304L/316L Stainless Steel
Vascomax C-300 Vascomax C-300
316L Stainless Steel
Welded Hermetic Welded Hermetic
10-32 Coaxial Jack
0.9 oz 25 gm
Optional versions have identical specifications and accessories as listed for the standard model except
[1]
where noted below. More than one option may be used.
[2]
[3]
[4]
[5]
[4]
N OTES:
[1]-5V output may be limited by the output bias.
[2]For +10 volt output, minimum 24 VDC supply voltage required. Negative 10 volt output may be
limited by output bias.
[3]Due to high sensitivity, the static pressure should be applied and removed very slowly. Rate should
prevent more than 10 Volt change in output until Output Bias Voltage returns to normal
(approximately 15 times discharge time constant).
[4]Typical.
[5]Zero-based, least-squares, straight line method.
[6]See PCB Declaration of Conformance PS023 for details.
SUPPLIED ACCESSORIES:
Model PCS-10AA Single point sensitivity coefficient at sensor minimum operating temperature (-
320°F / -196°C limit)
Model PCS-1AZ Sensitivity calibration at 100% and 10% of sensor range
Entered: ND Engineer: AJA
Date: 07/16/2024 Date: 07/16/2024 Date: 07/16/2024 Date: 07/16/2024 70091
3425 Walden Avenue, Depew, NY 14043
Revision: B
ECN #: 54975
OPTION AL VERSION S
Sales: RWM Approved: RPF Spec Number:
Phone: 716-684-0001
Fax: 716-684-0987
E-M ail: info@ pcb.com