Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Eureka Jade MK2 Freestanding
Summary of Contents for Eureka Jade MK2 Freestanding
- Page 1 Jade MK2 Freestanding Please keep these instructions for future reference. Dont forget to register your warranty using the QR code on the door glass or head to www.eurekaheating.com.au/warranty OPERATORS & INSTALLATION MANUAL OPERATION & INSTALLATION MANUAL...
-
Page 2: Safe Operation
• We are proud of the presentation of our products. If at any time you need to freshen up the paint, your local Eureka dealer has touch-up paint available for purchase. The heater is painted in Stove Bright Metal- lic Black - Paint code 6309. -
Page 3: Installation
Depending on your local authority requirements, a permit may be required for the installation of your heat- er. It is your responsibility to arrange the same. Flue Requirements: As per the dimensions in Table A (referencing figures 1 and 2), the Eureka Jade must be installed with either of the following flue types: •... -
Page 4: Clearances Information
Installation Hearth & Floor Requirements: If the appliance is to be installed onto a combustible floor, a cement sheet or similar non-combustible hearth or floor protector that has a thermal resistivity of 0.026m² must be placed in between the appliance and the combustible floor. - Page 5 Carton Dimensions (overall) 680W x 515D x 845H Installing Baffle Plates Your Eureka Jade utilizes a dual baffle plate system with a 6mm upper baffle and a 6mm dual skinned lower baffle with incorporated secondary air. When removing the baffle plates to clean the flue, the baffle plates must be inspected and replaced in the configuration as shown in Figure 3.
- Page 6 Installation Lower Baffle Installation 1. Position the baffle in the door opening as per (1) with the baffle lip facing the floor and the air in- take tubes facing the ceiling. 2. Feed the baffle through the door opening, towards the right rear corner of the firebox. 3.
- Page 7 Firebrick Installation, Care & Maintenance Fitting the Firebricks and Firebrick Retainer Your Eureka Jade requires firebricks to be installed to ensure that the fire operates correctly, and to prevent dam- age to the firebox through excessive heat. This fireplace uses two different size firebricks. Please use Table B and Figure 5 below to differentiate between each brick and its installation location.
- Page 8 Installation Flue and chimney requirements The flue pipe shall extend not less than 4.6m above the top of the floor protector. Installation must be carried out by a licensed installer in accordance with AS/NZS 2918:2018 (AS2918 Extracts below Illustrate minimum flue clearances). 6000 3000 More than 3000...
- Page 9 Removal of the door is carried out in reverse order of installation. Take care not to damage the door rope when removing or reinstalling the door. Final Inspection Prior to Use Before lighting the first fire in your new Eureka wood heater, check the following list of items to ensure that your heater will perform correctly, and safely: •...
-
Page 10: General Operation
To open the door rotate the handle 90 degrees counter-clockwise, and pull outward. To close the door, push the door shut and rotate the handle 90 degrees clockwise. The door should swing freely during both operations; if it does not, consult your Eureka dealer. - Page 11 Operating your Eureka The door should remain closed during operation, except for when you are lighting or re-fueling your fire. The heater is unable to circulate air inside the firebox effectively with the door open, and extended periods of the door being open during operation can result in smoke escaping into the room.
- Page 12 Firstly carefully remove the bricks, brick retainer and firebox baffles following the instructions given on pages 5,6 & 7. Close the heater door. Obtain a 150mm flue brush from you local Eureka dealer. Proceed to a position where you can access the flue cowl, and remove it from the flue. Follow the instructions provided with your flue brush to assemble it, slowly push the brush down the chimney until it stops.
- Page 13 Maintaining & Servicing your Eureka Fitting a New Door Seal • Remove the door from the wood heater (See “Fitting or Removing the Door” in the installation section above) • Place the door face down on a soft flat surface to protect paintwork and glass.
-
Page 14: Troubleshooting
Troubleshooting Heater Emitting Smoke while door open • It is normal for your wood burning heater to emit a certain amount of smoke when the door is opened during operation. Smoke will move in the path of least resistance as it rises from the fire, and when your heater door is opened, the opening becomes that path of least resistance. - Page 15 Troubleshooting Sluggish or Lazy Fire • Check that the baffle plates are installed correctly and there is no build up on baffle plates. • A sluggish or lazy fire can be caused by a number of different factors, or a combination of several factors.
- Page 16 60% of the wood’s potential heat is released. Understanding combustion principles and learning how to manipulate various conditions surrounding the operation of your Eureka wood heater enables you to achieve maximum comfort and efficency from your Australian made wood heater.
- Page 17 Basic Spare Parts Description Gason P/N Lower Baffle Plate 238833 Upper Baffle Plate 238835 Door Glass 236496 Door Assembly 238826 Door Handle assembly 238838 Ash Deflector 236257 Door rope (16mm OD, 1.5m Required) 203604 Firebrick set 236260 Brick retainer 236785 Door Handle 236505 Door Handle assembly kit...
- Page 18 Scan the QR code to complete your warranty registration online.
-
Page 19: Warranty
WARRANTY 1. Subject to clauses 2 & 3 of this warranty, A.F. Gason Pty Ltd ACN 004 667 556 warrants the following components of its heaters against defects in workmanship and/or materials for the following periods from the date of purchase: a) the firebox for ten years;...
Need help?
Do you have a question about the Jade MK2 Freestanding and is the answer not in the manual?
Questions and answers