Table of Contents
Advertisement
Quick Links
•
The installation of this appliance must be carried out as per this manual and the
We recommend that you use a
•
If in doubt do not hesitate to contact your local Jindara or Eureka dealer.
•
This appliance weighs in excess of 230 kilograms. Extreme care should be taken when handling the appliance.
Hole cutting dimensions
1015mm
1015mm
Clearances to combustibles
A minimum 1000mm
wide x 1800mm
deep x 12mm thick
protector should
be used under and in
front of the appliance
1000mm
when installing. The
protector should
extend 500mm in
front of the appliance
base on both doors.
!
Minimum
This Heater has been tested to AS2918:2001 Appendix B.
Test Report No. HCMG/14/069A using an Australian Standard
kit. For the through wall installation additional
8˝ stainless is to be
then a 9˝ mesh
shield are to be installed, both to ceiling height.
(See diagram opposite)
F:\Docs\Manuals\Heaters\GPN 214835 Thru Wall
Duet SRS2/Duplicity Through Wall Kit
(Part No. 214813)
Installation Instructions
Read and follow these instructions (in conjunction with the Duet
SRS2/Duplicity Freestanding manual) carefully before installing this appliance.
installer to carry out the installation.
If cutting hole through
a plasterboard wall
ensure wall width is
within 100mm
minimum to 115mm
maximum in thickness.
If constructed in brick
ensure wall width is
within 100mm
minimum to 145mm
maximum in thickness.
Internal wall
5
0
0
m
m
400mm
1800mm
requirements
over the 7˝ stainless active
shield and a 10˝ stainless steel
SAVE THESE INSTRUCTIONS
manufacturer's
Triple skin
ceiling upwards
See
Note 1
Hearth
120mm
5
0
0
m
m
Note 1: A combustible mantle must be no lower
than 500mm from top plate of heater.
Note 2: Internal wall noggin must not be lower
than 500mm above top plate of heater (a steel
noggin is permitted lower than 500mm).
These must be used to make the installation conform.
120mm
min.
NB: First
height 4600 mm (+/– 300mm) from
from
150mm
drop box
500mm
220mm
1015mm
(cutout)
7˝ stainless
8˝ stainless
9˝ solid back
mesh
10˝ stainless steel
shield up to
drop box height
protector
See
Note 2
1015mm
(cutout)
Advertisement
Table of Contents
Related Manuals for Eureka Jindara Duet SRS2/Duplicity
Summary of Contents for Eureka Jindara Duet SRS2/Duplicity
-
Page 1: Installation Instructions
We recommend that you use a installer to carry out the installation. • If in doubt do not hesitate to contact your local Jindara or Eureka dealer. • This appliance weighs in excess of 230 kilograms. Extreme care should be taken when handling the appliance. - Page 2 Parts 1. Fascia Assembly - Inbuilt side 2. Fascia Assembly - Freestanding side 3. Panel fascia - lower left hand 4. Panel fascia - lower right hand 5. Spray can 6. 10 off 1/2” x 8G self tapping screws 7. 4 springs 8.
- Page 3 Flue Spigot Step 3 1. Use a square to ensure the Inbuilt Fascia Assembly is perfectly vertical. 2. Using a 3mm dia drill bit, drill holes (C) and (D) through the Inbuilt Fascia Assembly and into the side of the heater. Insert screws (Part 7) and tighten.
- Page 4 Any enquiries contact the dealer from whom you purchased your heater. PLEASE COMPLETE: Dealer name: Dealer Address: Phone Number: Please attach your original purchase dockets to this instruction book for future reference. Heating Phone (03) 9729 1422 Fax (03) 9729 1455 Gason Heating reserves the right to modify or alter specifications, materials, etc in the interests of product improvement.
Need help?
Do you have a question about the Jindara Duet SRS2/Duplicity and is the answer not in the manual?
Questions and answers