Download Print this page
GE CYNC CSWONBLBWF1NN/ST1P Installation Manual
GE CYNC CSWONBLBWF1NN/ST1P Installation Manual

GE CYNC CSWONBLBWF1NN/ST1P Installation Manual

3-way smart wall switch

Advertisement

Quick Links

3-Way
Smart Wall Switch
Installation Guide
3-Wire Smart Switches & Dimmers

Advertisement

loading
Need help?

Need help?

Do you have a question about the CYNC CSWONBLBWF1NN/ST1P and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GE CYNC CSWONBLBWF1NN/ST1P

  • Page 1 3-Way Smart Wall Switch Installation Guide 3-Wire Smart Switches & Dimmers...
  • Page 2 Add your Smart Switches to the Cync App For set up help, visit gelighting.com/cync GE and C by GE are trademarks of General Electric Company. Used under trademark license. Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc. or its affiliates.
  • Page 3: Compatibility Requirements

    If you are using less than 15 (Wire is usually green, green with Watts, non-dimmable LED bulbs, a yellow stripe, or copper) or C by GE and Cync Smart Wi-Fi 802.11 b/g/n @ 2.4 GHZ is Bulbs on the circuit, you will need Switch...
  • Page 4 Installing C by GE or Cync Smart Switches on a 3-Way or Multi-Way circuit You Got This! requires ALL switches on the same circuit to be a C by GE or Cync Smart Switch. 3-Way circuits can vary depending on the method used at the time the home was wired.
  • Page 5 BEFORE YOU DO ANYTHING! Check for Compatible Wiring Turn Off the Power! STEP 1 STEP 1 Do not disconnect any wires at this Turn off the power for the switch stage. We recommend taking a picture location at the circuit breaker box. of your wiring before proceeding for future reference.
  • Page 6: Turn Off The Power

    Restore Power Identify the LINE and LOAD STEP 1 Make sure that the light is off. Then, check the black common terminals on both switches using a voltage tester. One of them should test positive for voltage, and the other one should not.
  • Page 7 Cync or C by GE smart lights • Install our Fixture Adaptor to the actual fixture in the ceiling. For install Combination of bulbs listed above instructions and where to get a C by GE or Cync Fixture Adaptor (available separately), contact Customer Support at 1-844-302-2943...
  • Page 8 One of these wires will be used to provide power to the C by GE or Cync Smart Switch on the load side of the circuit. C by GE or Cync 3-Wire Smart Switches...
  • Page 9 LOAD on TRAVELER wire from the wall to the the first switch to the LOAD on this black LOAD wire on the C by GE or switch. We used the black traveler Cync Smart Switch. For our example, in our example.
  • Page 10: Troubleshooting

    TROUBLESHOOTING Secure the Smart Switches LED indicator light or light ring will flash blue until the switch is added to the Cync App. LED indicator light or light ring will not illuminate if wired incorrectly or if the switch circuit does not meet the specified load requirements. STEP 1 Important: Only the load switch will turn the light on/off until the Neatly push the wires back into the boxes.
  • Page 11 Enable 3-Way Control in the Cync App Additional Information and Warnings FCC Compliance Statement Compliance Notice: This equipment has been tested and found to comply with the limits NOTE: Only the load switch will turn the light on/off until the two Smart for a Class B digital device, pursuant to part 15 of the FCC Rules.
  • Page 12 This device complies with Part 15 of the FCC Rules and Industry For supply connections, use copper wire only rated at 75ºC Canada license-exempt RSS standard(s) Operation is subject to the following two conditions: CAUTION - High Voltage - Disconnect power supply before 1.
  • Page 13 Like your new Smart Switch? Share your experience! Leave a review where you purchased the product.