Ziton ZP2-F1-99 Installation Manual
  1. Manuals
  2. Brands
  3. Ziton Manuals
  4. Smoke Alarm
  5. ZP2-F1-99
  6. Installation manual
Ziton ZP2-F1-99 Installation Manual

Ziton ZP2-F1-99 Installation Manual

Hide thumbs Also See for ZP2-F1-99:
Table of Contents

Advertisement

Quick Links

Download this manual
ZP2 Series Installation
Manual
www.acornfiresecurity.com
www.acornfiresecurity.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZP2-F1-99 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Ziton ZP2-F1-99

Summary of Contents for Ziton ZP2-F1-99

  • Page 1 www.acornfiresecurity.com ZP2 Series Installation Manual www.acornfiresecurity.com...

  • Page 2: Table Of Contents

    www.acornfiresecurity.com Content Important information ii Chapter 1 Introduction 1 Product range 2 Product compatibility 3 Product overview 4 Chapter 2 Installation 17 Electrical safety 18 Cabinet and PCB layout 19 Cabinet installation 21 Connections 26 Chapter 3 Configuration and commissioning 37 Introduction 38 Maintenance level operation and configuration 41 Installer level operation and configuration 56...

  • Page 3: Important Information

    www.acornfiresecurity.com Important information Introduction This is the installation manual for the ZP2 Series fire alarm, repeater, and evacuation control panels. Read these instructions and all related documentation entirely before installing or operating this product. Firmware compatibility Information in this document covers control panels with firmware version 3.7 or later.

  • Page 4: Introduction

    www.acornfiresecurity.com Chapter 1 Introduction Summary This chapter provides an introduction to your control panel, the main controls, and the indicators. Content Product range 2 Product compatibility 3 Product overview 4 The user interface 4 Front panel controls and indicators 6 LCD controls and indicators 11 Acoustic indicators 13 Conditions 14...

  • Page 5: Product Range

    www.acornfiresecurity.com Chapter 1: Introduction Product range The series includes the fire alarm, repeater, and evacuation panels shown below. Table 1: Fire alarm, repeater, and evacuation panels Model Description ZP2-E1(-S) [1] One-loop addressable fire and evacuation alarm control panel ZP2-E2(-S) Two-loop addressable fire and evacuation alarm control panel ZP2-ER(-S) Addressable fire and evacuation alarm repeater panel ZP2-F1(-S)

  • Page 6: Product Compatibility

    www.acornfiresecurity.com Chapter 1: Introduction Product compatibility Products compatible with these control panels are listed in the product compatibility list. Only those products specified in the compatibility list are guaranteed to be compatible. To download the latest product compatibility list, visit firesecurityproducts.com. ZP2 Series Installation Manual www.acornfiresecurity.com...

  • Page 7: Product Overview

    www.acornfiresecurity.com Chapter 1: Introduction Product overview This topic provides an introduction to the control panel user interface, LCD, operator controls, and indicators. For a detailed overview of front panel controls and indicators, see “Front panel controls and indicators” on page 6. The user interface Figure 1: Fire panel user interface (with fire routing and fire protection controls) 1.
  • Page 8 www.acornfiresecurity.com Chapter 1: Introduction Figure 2: Evacuation panel user interface 1. Supply LED 14. Panel Silence button and LED 2. General Test LED 15. Sounder Start/Stop Button and LED 3. General Disable LED 16. System Fault LED 4. General Fault LED 17.

  • Page 9: Front Panel Controls And Indicators

    www.acornfiresecurity.com Chapter 1: Introduction Configuration options Depending on your configuration, the labels for some interface buttons may change. See Table 2 below. Table 2: Configured changes to interface buttons and LEDs Item EN 54 NEN 2575 All Output Groups Start/Stop All Evacuation Start/Stop Programmable output group start/stop Evacuation area sounders start/stop [1]...
  • Page 10 www.acornfiresecurity.com Chapter 1: Introduction Control/LED LED colour Description Fire Routing Delay Yellow Enables or disables a previously configured fire routing button and LED delay. Cancels a delay as it counts down and activates fire routing. A steady LED indicates that a delay is configured and enabled.
  • Page 11 www.acornfiresecurity.com Chapter 1: Introduction Control/LED LED colour Description Programmable Yellow Starts or stops the output group associated with the start/stop button and programmable button. A steady yellow LED indicates that the output group associated with the button is active. A flashing yellow LED indicates that a delay is counting (the output group is activated when the configured delay elapses or when the delay is cancelled).
  • Page 12 www.acornfiresecurity.com Chapter 1: Introduction Control/LED LED colour Description Panel Silence button Yellow Silences the control panel buzzer. and LED A steady LED indicates that the buzzer has been silenced. Reset button and LED Yellow Resets the control panel and clears all current system events.
  • Page 13 www.acornfiresecurity.com Chapter 1: Introduction Output group LED indications The control panel can be configured to have several sounder, fire routing, or fire protection output groups. Some groups may use the same indicators. When such groups have the same status, that status is indicated. In the case of conflicting status, the highest priority status is displayed.

  • Page 14: Lcd Controls And Indicators

    www.acornfiresecurity.com Chapter 1: Introduction LCD controls and indicators Figure 3: LCD controls and indicators 1. Day/night mode indicator 2. System date and time (and active fire routing delay or extended fire routing delay countdown) 3. Control panel network status (stand-alone, networked, repeater) 4.
  • Page 15 www.acornfiresecurity.com Chapter 1: Introduction Icons displayed on the LCD Icons displayed on the LCD are shown below. Table 5: LCD icons and descriptions Icon Description This icon indicates that the primary sensitivity mode Day mode (network) setting for control panels in the fire network is day mode.

  • Page 16: Acoustic Indicators

    www.acornfiresecurity.com Chapter 1: Introduction Icon Description This icon indicates a manual call point alarm (sprinkler). Manual call point alarm (sprinkler) [1] This icon indicates a manual call point alarm Manual call point alarm (“hausalarm”). This is a local alarm with no fire routing (“hausalarm”) [1] activation.

  • Page 17: Conditions

    www.acornfiresecurity.com Chapter 1: Introduction Conditions A summary of system events logged as conditions is shown below. Table 7: System events logged as conditions Condition type Description Alert A device is in alarm but the system is waiting for an additional alarm event to confirm the zone alarm Configuration device connected A control panel configuration session is initiated via an external device (PC, laptop, etc.)
  • Page 18 www.acornfiresecurity.com Chapter 1: Introduction The following system status events are also added to the event log (but are not included in the control panel current events report). Table 8: Other system status events added to the event log Event Description Actions An output group is activated or deactivated or a programmable system command is executed (via the...
  • Page 19 www.acornfiresecurity.com Chapter 1: Introduction ZP2 Series Installation Manual www.acornfiresecurity.com...

  • Page 20: Installation

    www.acornfiresecurity.com Chapter 2 Installation Summary This chapter provides detailed installation and connection information for your control panel. Caution: This product must be installed and maintained by qualified personnel adhering to the CEN/TS 54-14 standard (or the corresponding national standard) and any other applicable regulations. Content Electrical safety 18 Cabinet and PCB layout 19...

  • Page 21: Electrical Safety

    www.acornfiresecurity.com Chapter 2: Installation Electrical safety WARNING: Electrocution hazard. To avoid personal injury or death from electrocution, remove all sources of power and allow stored energy to discharge before installing or removing equipment. Caution: Equipment damage hazard. This product is sensitive to electrostatic discharge (ESD).

  • Page 22: Cabinet And Pcb Layout

    www.acornfiresecurity.com Chapter 2: Installation Cabinet and PCB layout Figure 4: Large cabinet and PCB layout (two-loop control panel) 1. 24V connector 9. COM0 and COM1 serial ports 2. COM2 serial port 10. COM0 and COM1 interface connectors 3. Loop and fire system connectors 11.
  • Page 23 www.acornfiresecurity.com Chapter 2: Installation Figure 5: Small cabinet and PCB layout (two-loop control panel) 1. Loop and fire system connectors 8. COM0 and COM1 interface connectors 2. Spirit level 9. Battery connector 3. Earth studs 10. Power supply connector 4. Ethernet connector 11.

  • Page 24: Cabinet Installation

    www.acornfiresecurity.com Chapter 2: Installation Cabinet installation Where to install the control panel Install the control panel in a location that is free from construction dust and debris, and immune to extreme temperature ranges and humidity. See Chapter 5 “Technical specifications” on page 117 for more information on the operating temperature and relative humidity specifications.

  • Page 25: Adding The Menu Inserts

    www.acornfiresecurity.com Chapter 2: Installation To fix the cabinet to the wall: 1. Hold the cabinet to the wall at the required installation height. 2. Ensure that the cabinet is level using the built-in spirit level and mark drill points on the wall. 3.

  • Page 26: Connecting The User Interface Cable

    www.acornfiresecurity.com Chapter 2: Installation The inserts are numbered 1, 2, 3, and 4, and are inserted at the location indicated (with the printed area facing the front of the control panel). For evacuation panels, remember to add descriptions for any output groups assigned to the programmable buttons to insert 3.

  • Page 27: Connecting The Internal Printer And Loading Paper

    www.acornfiresecurity.com Chapter 2: Installation Connecting the internal printer and loading paper This topic shows you how to connect the internal printer and load the printer with paper. See “Printer configuration” on page 73 for printer configuration options. The internal printer is only available on selected models. Connecting the internal printer Connect the internal printer as shown below.
  • Page 28 www.acornfiresecurity.com Chapter 2: Installation Loading paper Load the paper for the internal printer as shown below. Figure 11: Loading the paper for the internal printer ZP2 Series Installation Manual www.acornfiresecurity.com...

  • Page 29: Connections

    www.acornfiresecurity.com Chapter 2: Installation Connections Recommended cables Recommended cables for optimal system performance are shown in the table below. Table 9: Recommended cables Cable Cable requirements Maximum cable length Mains cable 3 × 1.5 mm Shielded cable (75 Ω and 700 nF max.) [1] Loop cable 3.5 km with KAL51A cable 12 to 26 AWG (0.13 to 3.31 mm²)

  • Page 30: Overview Of Fire System Connections

    www.acornfiresecurity.com Chapter 2: Installation The PCB terminal earthing connections only improve noise immunity in very specific environmental conditions. In some cases, leaving the earth fully isolated provides the best protection against EMI. To determine noise immunity, check the communications error rate and the stability of analogue values for installed devices.

  • Page 31: Connecting Loops

    www.acornfiresecurity.com Chapter 2: Installation Figure 13: Overview of EN 54-13 fire system connections with a single Class A loop 1. 2010-FS-EOL end-of-line device 2. Fault indicating equipment 3. Earth connection (connected to the earth studs in the control panel cabinet, not to the loop connector).
  • Page 32 www.acornfiresecurity.com Chapter 2: Installation • Install loop devices with a high current consumption as close as possible to the control panel. • Ensure that the loop cable complies with the cable specifications outlined in “Recommended cables” on page 26. • If using shielded loop cable, ensure that the shield is continuous (connected through to each loop device).

  • Page 33: Connecting Loop Devices

    www.acornfiresecurity.com Chapter 2: Installation Connecting loop devices Each loop can support up to 127 devices (using the address range 1 to 127). For detailed loop device installation information, see your device installation sheet. Connecting inputs Input functionality Each control panel has two supervised inputs, marked INPUT1 and INPUT2. For input configuration, see “Field configuration”...
  • Page 34 www.acornfiresecurity.com Chapter 2: Installation Output Description Supervision FIRE OUT This fire output is activated when the control panel Short circuit, open SUPERVIS [1] is in alarm status. circuit Note: This output does not comply with EN 54-13 requirements. FIRE OUT RELAY This relay output is activated (a short circuit Not supervised between the common (C) and normally open (NO)

  • Page 35: Connecting The Mains Power Supply

    www.acornfiresecurity.com Chapter 2: Installation Configurable outputs The number of configurable outputs depends on the control panel model and output class configuration, as shown below. Table 13: Configurable outputs for panels [1] Control panel Configurable outputs (Class B) Configurable outputs (Class A) One-loop panel 2 (OUT1 and OUT2) 1 (OUT1/OUT2)
  • Page 36 www.acornfiresecurity.com Chapter 2: Installation Keep mains cables separate from other cabling to avoid potential short circuits and interference. Use the provided cable ties to secure mains cables to the cabinet on either side of the fuse terminal block to prevent movement. Caution: If the control panel has a network board installed, the mains cable must enter the cabinet from the bottom for proper operation.

  • Page 37: Connecting The Batteries

    www.acornfiresecurity.com Chapter 2: Installation Connecting the batteries The control panel requires two 12 V, rechargeable, sealed lead-acid batteries with 7.2, 12, or 18 Ah capacity (see “Battery maintenance” on page 115). Batteries are located inside the control panel cabinet and must be installed in series.
  • Page 38 www.acornfiresecurity.com Chapter 2: Installation Ring configuration Ring network configuration is recommended as it provides for redundancy in the transmission path. For ring configuration (Class A), use both ports to connect all network boards or control panels to form a ring, as shown below. Figure 18: Fire network ring configuration Bus configuration Caution:...

  • Page 39: Connecting An External Printer Or Ascii Terminal

    www.acornfiresecurity.com Chapter 2: Installation Connecting an external printer or ASCII terminal To print control panel events in real time, connect an external EPSON LX300 printer or ASCII terminal to COM0 or COM1. Note: This option requires the 2010-2-232-KIT (not supplied). The kit contains a 3 m cable and the 2010-2-232-IB isolation board required for external RS-232 device connections.

  • Page 40: Configuration And Commissioning

    www.acornfiresecurity.com Chapter 3 Configuration and commissioning Summary This chapter provides configuration and commissioning information for your control panel and fire detection system. Content Introduction 38 Load/Save configuration 68 User levels 38 Expansion board Configuration overview 39 configuration 70 Maintenance level operation and Load auxiliary files 70 configuration 41 System update 72...

  • Page 41: Introduction

    www.acornfiresecurity.com Introduction User levels Access to some of the features of this product is restricted by the user level assigned to a user account. Public The public level is the default user level. This level allows basic operational tasks, such as responding to a fire alarm or fault warning at the control panel.

  • Page 42: Configuration Overview

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Table 15: User level timeouts User level Automatic timeout period Operator 2 minutes Maintenance 10 minutes Installer 10 minutes To enter a password-protected level: 1. Press F4 (Main menu). The username and password prompt appears on the LCD.
  • Page 43 www.acornfiresecurity.com Chapter 3: Configuration and commissioning When configuring your fire system using the Configuration Utility: 1. Configure the communications settings if you plan to download configurations using an Ethernet connection. This is not required if you plan to save configurations to a PC connected to the control panel USB connector. 2.

  • Page 44: Maintenance Level Operation And Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Configuration options The options listed below are available when making configuration changes to the control panel. The control panel configuration (and configuration revision) is only updated when configuration changes are applied by pressing F3 (Apply). The configuration revision change and timestamp are recorded in the Revision report and can be accessed at operator, maintenance, and installer levels.

  • Page 45: The Field Setup Menu

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning The Main menu The maintenance level Main menu is shown below. Figure 20: Maintenance level Main menu The Field setup menu Use the Field setup menu to set timeout values for zone test and disablement operations.

  • Page 46: The Panel Setup Menu

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning The Panel setup menu Use the Panel setup menu to set the date and time, to synchronize the date and time in a fire network, and to set day or night mode sensitivity settings. Date and time Select Date and time to change the control panel date and time.
  • Page 47 www.acornfiresecurity.com Chapter 3: Configuration and commissioning To set a day/night schedule: 1. Select Panel setup from the Main menu. 2. Select Day/Night mode, and then select Day/Night schedule. 3. Select the day you want to configure. 4. Enter the time that day mode starts using the hh:mm format (for example, 08:00).
  • Page 48 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Additional day/night mode settings Select Day/Night setup to configure additional settings such as manual override of day/night mode schedule and holiday calendar mode changes or delay behaviour in night mode. The configuration options available are shown in the table below. Table 18: Additional day/night mode options Option Description...

  • Page 49: The Communications Menu

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Notes on day and night mode settings Day/night mode may be configured to change with a remote input. Depending on the installation settings, the system may be configured to use an external input to override the day/night mode setting until the following programmed change (if any).

  • Page 50: The Disable/Enable Menu

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Removing a USB device Select Remove USB device to safely remove a USB device connected to the control panel (for example, a flash drive). Caution: Failure to remove a USB flash drive as described may result in loss of data and/or damage to your flash drive.

  • Page 51: The Test Menu

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Disabling a system feature or device To disable a feature or device: 1. Select Disable/Enable from the Main menu. 2. Select Disable (or Remote Disable if the feature or device is not local to the control panel).
  • Page 52 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Testing zones To test a zone: 1. Select Test from the Main menu. 2. Select Zones. 3. Select the zone to test, and then press the jog dial to start the test. Press the jog dial again to end the test for the selected zone.
  • Page 53 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Testing control panel and loop output activation To test activation of an output: 1. Select Test from the Main menu. 2. Select Output test from the Test menu, and then select Panel outputs or Loop outputs.
  • Page 54 www.acornfiresecurity.com Chapter 3: Configuration and commissioning To test remote features or devices: 1. Select Test from the Main menu, and then select Remote Test. 2. Select Panel and enter the control panel Firenet ID. 3. Select Element, and then select Device, Group, or Zone. Enter the device loop and address information, the group number, or the zone number.

  • Page 55: The Reports Menu

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning The Reports menu Use the Reports menu to view, clear, or back up the event log and to display a variety of system status reports. The reports available to maintenance users are shown in the table below. Table 19: Reports available to maintenance users Report Description...
  • Page 56 www.acornfiresecurity.com Chapter 3: Configuration and commissioning The event log can include a maximum of 9,999 entries. When the maximum number of entries is reached, the oldest entries are deleted as new entries are recorded. Backing up the event log Select Backup to create a backup of the event log. The backup reports are saved to a USB flash drive (not supplied) in XML format and can be viewed with the Configuration Utility.

  • Page 57: The Password Setup Menu

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Saving reports Select Save report to save a report. Reports are saved to a USB flash drive (not supplied) in XML format and can be viewed with the configuration utility PC application. Note: Use only FAT32 file system USB flash drives with a maximum capacity of 32 GB.
  • Page 58 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Managing users Select Manage users to edit, delete, or create operator user accounts. The control panel allows for a maximum of 20 user accounts (all user levels combined). To edit an operator user account: 1.

  • Page 59: Installer Level Operation And Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Installer level operation and configuration The installer level is password-protected and is reserved for authorized users installing and configuring the control panel and the fire system. The default password for the default installer user is 4444. The Main menu The installer level Main menu is shown below.

  • Page 60: Id Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Option Description Load auxiliary files Loads auxiliary files from a USB flash drive. Auxiliary files that can be loaded include custom standby and alarm screens, and updated language or font files for extended language support. System update Loads control panel firmware updates.

  • Page 61: Regional Options

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Regional options Select Regional options to set the regional operating mode. Available options are shown in the table below. Table 21: Regional operating modes Operating mode Region EN 54-2 (default) European Union EN 54-2 Evacuation European Union (Spain) NBN S 21-100 [1] European Union (Belgium)
  • Page 62 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Option Description Event filter Configures the types of events to repeat from other control panels in the fire network. Command filter Configures the types of commands sent to the fire network in control panels with the corresponding global controls configured. Class B Configures a Class B network.
  • Page 63 www.acornfiresecurity.com Chapter 3: Configuration and commissioning filter has condition and fault reporting disabled, the repeater repeats only alarm, prealarm, alert, and technical alarm conditions. Therefore, in Repeater mode the panel uses the network: • To process and display the events received from any remote panel that affect the local zones in the system •...
  • Page 64 www.acornfiresecurity.com Chapter 3: Configuration and commissioning 4. Press F4 (Enter), and then press F1 (Back). 5. Press F1 (Save), F3 (Apply), F4 (Discard), or F2 (Exit). Remember to apply saved settings from the Main menu. The commands that can be controlled globally are detailed in Table 24 below. Event filter Select Event filter to configure the types of events to repeat from other control panels in the fire network.

  • Page 65: Communications Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning To change the Command filter settings: 1. Select Panel setup from the Main menu. 2. Select Firenet, and then select Command filter. A list of available commands that can be configured is displayed. 3. Select all commands to be filtered. 4.
  • Page 66 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Option Description Default value Direct [2] If checked, enables direct email support Disabled Configures the DNS server IP address used for direct 000.000.000.000 email support [1] If the default port is changed, the port configuration in the Configuration Utility PC application must also be updated.
  • Page 67 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Email server Note: These settings have no effect if direct email support is enabled in TCP/IP. See “TCP/IP” on page 62. Select Email server to configure the email server settings for sending configured notification emails. IT support may be required to configure this option. To configure the email server: 1.

  • Page 68: Other Settings

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Other settings 24V auxiliary Select 24V AUX config to configure the 24V AUX output state during reset and when the control panel is running on battery power. The default setting for both options is NO (the 24V AUX output is not deactivated). To change the configuration: 1.
  • Page 69 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Sounders re-sound Select Sounder re-sound to configure stopped sounder functionality when new zone alarms are reported. The available configuration options are shown below. The default setting is YES (sounders re-sound for new zone alarms). Note: By default, sounders only re-sound for a new alarm (in the same zone) if a manual call point alarm is reported following a detector alarm.
  • Page 70 www.acornfiresecurity.com Chapter 3: Configuration and commissioning To change the configuration: 1. Select Panel setup from the Main menu. 2. Select Other settings, and then select Self-test. 3. Select and check the Enabled check box. 4. Select TestH, and then enter the start time for the self-test (00:00 to 23:59). 5.

  • Page 71: Load/Save Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning By default the standard alarm display format is used (except for control panels operating in regional mode VdS 2540). To change the configuration: 1. Select Panel setup from the Main menu. 2. Select Other settings, and then select VdS settings. 3.
  • Page 72 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Note: Use only FAT32 file system USB flash drives with a maximum capacity of 32 GB. To load a configuration: 1. Open the control panel door and insert the USB flash drive with the configuration file into either of the USB type A connectors (see Figure 4 on page 19).

  • Page 73: Expansion Board Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Remember to apply saved settings from the Main menu. Expansion board configuration Select Expansion boards to add an installed expansion board to the control panel configuration. Note: If the installed expansion board firmware is not compatible with the control panel, a warning message is displayed.
  • Page 74 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Adding custom standby and alarm screens Select Splash screens to add custom standby and alarm screens in binary (BIN) format. To prepare custom screen images: 1. Convert the graphics file to BIN format using a graphics file converter or the Configuration Utility.

  • Page 75: System Update

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning 7. Press F1 (Save), F3 (Apply), F4 (Discard), or F2 (Exit). Remember to apply saved settings from the Main menu. 8. Remove the USB flash drive as described in “Removing a USB device” on page 47.

  • Page 76: Printer Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Printer configuration Select Printer configuration to configure internal, external, or terminal printers, where available. Configuration options are shown in the table below. By default, all printer configuration options are disabled. Table 29: Printer configuration options Option Description Used...

  • Page 77: Dact Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning DACT configuration Select DACT configuration to configure settings for an installed DACT expansion board. Configuration options are shown in the table below. Table 30: DACT configuration options Option Description General config Configures the DACT status (used or not used) and event reporting options Ethernet config Configures Ethernet settings for monitoring network communication...
  • Page 78 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Ethernet configuration Select Ethernet configuration to configure settings for monitoring network communication with the central monitoring station (CMS). Configuration options are shown in the table below. Table 32: Ethernet configuration options Option Description Default value Period Configures the heartbeat period (in seconds) Fails...
  • Page 79 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Table 34: Site configuration event types Option Description Configures alarm reporting Configures fault reporting Configures condition reporting Configures alarm and fault reporting Configures alarm, fault, and condition reporting Configures fault and condition reporting Configures alarm and condition reporting To change the configuration: 1.
  • Page 80 www.acornfiresecurity.com Chapter 3: Configuration and commissioning To change the configuration: 1. Select Panel setup from the Main menu. 2. Select DACT config, and then select CMS config. 3. Select the CMS to configure (1 to 7). 4. Configure all required settings. 5.

  • Page 81: Panel Activation Key

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning GPRS configuration Select GPRS configuration to configure general packet radio service (GPRS) settings. Configuration options are shown in the table below. Note: GPRS functionality requires an optional GPRS expansion board to be installed. Table 37: GPRS configuration options Option Description Default value...

  • Page 82: Auto Date And Time

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Table 38: Panel activation keys Description 2010-2-PAK-NET128 Increases the network capability to 32 nodes and 128 loops [1] 2010-2-PAK-NET256 Increases the network capability to 64 nodes and 256 loops [1] 2010-2-PAK-RMSDK Enables custom event reporting and command control using the Edwards software development kit (SDK) 2010-2-PAK-RMOH Enables the Contact ID protocol over Ethernet...

  • Page 83: Bms Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning BMS Configuration Select BMS Config to configure building management protocol settings (BACnet, Modbus). By default neither protocol is enabled. Table 40: BMS configuration options Option Description Default value Protoc Configures the BMS protocol (NO, BACnet, or Modbus) InitPan [1] Configures the initial panel address when using...

  • Page 84: Autosetup

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Option Description Activation configuration Configures output group delays and regional investigation time options. Loop class Configures the installation loop wiring Class (Class A or Class B). Autosetup Select Autosetup to automatically configure installed loop devices. Autosetup assigns a default configuration for each device type detected.

  • Page 85: Loop Device Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Loop device configuration Select Loop device configuration to manually add devices or to change the default configuration settings after autosetup. To add a device or to change a device configuration: 1. Select Field setup from the Main menu, and then select Loop device configuration.
  • Page 86 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Remote zones The control panel also considers an additional zone called remote zone (REMT) which spans all the zones in the system outside the control panel zones range. This virtual zone can be configured like any other zone in the system and it is important to define output group activation requirements when the panel receives remote alarms.
  • Page 87 www.acornfiresecurity.com Chapter 3: Configuration and commissioning To change the configuration: 1. Select Field setup from the Main menu, and then Zone configuration. 2. Select General config. 3. Make the required configuration changes. 4. Press F4 (Enter), and then press F1 (Back). 5.
  • Page 88 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Configuring the number of global zones helps to avoid zone overlap in installations where zone numbering is configured to avoid sharing some zones across the network. By configuring this setting, the same number of shared zones is maintained after upgrading the control panel firmware to version 3.5 (or later) and unexpected cross-panel activations are avoided.
  • Page 89 www.acornfiresecurity.com Chapter 3: Configuration and commissioning To change the zone configuration settings: 1. Select Field setup from the Main menu, and then Zone configuration. 2. Select Zone configuration, and then select the corresponding zone from the list of zones displayed. 3.
  • Page 90 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Option Description sD(B) The alarm is confirmed by the same detector but with longer inhibition time than the sD(A) confirmation option. Alarms generated by a manual call point are not confirmed and activate a control panel alarm immediately. aDaZ (type B EN 54-2) The alarm is confirmed by the same detector or by a different detector in the same local area.
  • Page 91 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Zone operating modes All zones must be configured as Mixed, Manual, Auto, MSP, or MHA. Information for each of these zone operating modes is shown in the table below. By default all zones are mixed. Table 48: Zone operating modes Operating mode Description...

  • Page 92: Panel I/O Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Note: When configuring a confirmed zone, remember that remote zones with the same zone number can activate a control panel alarm without confirmation. To avoid this type of unwanted alarm, configure the remote zones accordingly. Panel I/O configuration Panel input configuration Configurable options for control panel inputs are shown below.
  • Page 93 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Type Description Detector alarm. This input type can be used for connecting to aspirating detector Fire1 outputs. Manual call point alarm. This input type can be used for connecting to aspirating detector Fire2 outputs. PREAL Prealarm (unlatched).
  • Page 94 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Type Description Manual call point alarm (“hausalarm”). KEYSW Keyswitch access. Activation enables the Operator access level for the control panel (no password required). Only one input per control panel can be configured to use this mode. To enable or disable a control panel input: 1.
  • Page 95 www.acornfiresecurity.com Chapter 3: Configuration and commissioning The default setting is Class B. 7. Press F4 (Enter), and then press F1 (Back). 8. Press F1 (Save), F3 (Apply), F4 (Discard), or F2 (Exit). Remember to apply saved settings from the Main menu. Configurable output types are shown in the table below.
  • Page 96 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Output groups Select Output groups to configure the control panel output groups. Control panel outputs must be assigned to output groups for activation. An output group is a collection of outputs of the same type that activate and deactivate at the same time (they are commanded simultaneously).
  • Page 97 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Configurable options for output groups are shown below. Table 54: Configurable options for output groups Option Description Group_n Configures the output group number Type Configures the output group type Control Enables or disables the output group [BLANK] Output description To configure a default output group:...
  • Page 98 www.acornfiresecurity.com Chapter 3: Configuration and commissioning 7. Press F4 (Enter), and then press F1 (Back). 8. Press F1 (Save), F3 (Apply), F4 (Discard), or F2 (Exit). Remember to apply saved settings from the Main menu. Output group activation Output groups can be activated by any of the following: •...
  • Page 99 www.acornfiresecurity.com Chapter 3: Configuration and commissioning To configure delayed output group activation: 1. Select Field setup from the Main menu, and then select Output groups. 2. Select Confirmations, and then select the output group to configure. A list of the available output groups that allow alarm confirmation configuration is displayed.
  • Page 100 www.acornfiresecurity.com Chapter 3: Configuration and commissioning By default, all programmable buttons are set to sounder group 1. Notes: • To comply with EN 54 requirements, default output groups 1 (SND), 2 (SND), 971 (FR), and 981 (FP) must be linked to a programmable button when any other output group of the same type is linked to a programmable button.

  • Page 101: Activation Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Activation configuration Select Activation configuration options to configure the activation delays for output groups, investigation times, and general sounders behaviour (sounder silencing and second stage usage). Note: This option is not available on repeater panels. Delay configuration options are shown in the table below.
  • Page 102 www.acornfiresecurity.com Chapter 3: Configuration and commissioning To configure the output group delay: 1. Select Field setup from the Main menu, and then select Activation configuration. 2. Select the output group type to configure (Sounder, Fire routing, etc.). 3. Select Group_n, and then select ALL (to configure common delay settings for all output groups of the type selected) or select the output group number (to configure custom delay settings for a single output group of the type selected).
  • Page 103 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Notes • Global delay options only set the delays of the zones that are enabled to activate the sounder or fire routing group. For example, if sounders and fire routing activate for zone 1 with a delay of 10 seconds and for zone 5 with a delay of 2 minutes, when selecting this option, sounders and fire routing will activate with the same selected delay after alarms in zones 1 or 5 and will not activate for all the other zones.
  • Page 104 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Outputs assigned to an output group (for example, output group 5 SND) are activated depending on alarms in the fire network and with the corresponding delays. For example, if we have a one-loop control panel with the initial zone set to 100 and we want to configure sounder output group number 5, the following can be configured with this option: •...
  • Page 105 www.acornfiresecurity.com Chapter 3: Configuration and commissioning To configure general delays: 1. Select Field setup from the Main menu, and then select Activation configuration. 2. Select General delays. 3. Select Investigation mode, and then select the type of investigation mode required. See “Investigation mode”...
  • Page 106 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Table 59: Regional investigation time modes Setting Description NO (default) No investigation mode is required. MAX_ACK_T Maximum acknowledgement time. The configured investigation time starts to count down when the control panel reports a detector alarm. If the alarm is acknowledged during the investigation time (by pressing the Panel Silence button), then any sounder or fire routing delays continue to be processed as configured.
  • Page 107 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Investigation time Select Investigation time to configure the duration (in seconds) of the investigation time for the configured investigation mode. Minimum, maximum, and default values for each mode are shown in the table below. Table 60: Investigation time values per mode Investigation mode Minimum...
  • Page 108 www.acornfiresecurity.com Chapter 3: Configuration and commissioning There are three configurable time periods, as shown in the table below. Table 61: Warning time, warning delay, and delay Time period Description Warning time The time from when the alarm is reported until the sounders activate the evacuation tone (or the corresponding evacuation tone delay starts to count down) Warning delay [1]...

  • Page 109: Loop Class Configuration

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Sounders silence disable time Note: This feature is not available for control panels operating in NBN S21-100 or EN 54 Evacuation mode (any configured sounder silence disable times are ignored). To prevent the immediate silencing of sounders when an alarm is first reported, the Sounder Start/Stop button may be temporarily disabled for a preconfigured period of time when a configured sounder delay is counting down.

  • Page 110: Tests

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Tests Diagnostics Select Diagnostics for tools to support troubleshooting during installation. The diagnostics tests available are shown in the table below. Table 62: Diagnostics options Option Description Individual device Polls loop devices and retrieves raw data for device diagnostics. Important: This option alters the normal detection scan to only poll the device under test.

  • Page 111: Password Setup

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Table 63: Individual device diagnostics tests Polling mode [1] Description STA_AB, STA_A, STA_B Configures status polling mode AV1_AB, AV1_A, AV1_B Configures analogue value 1 polling mode AV2_AB, AV2_A, AV2_B Configures analogue value 2 polling mode GRP_AB, GRP_A, GRP_B Configures group status polling mode [1] AB, A, and B indicate the loop channel used.
  • Page 112 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Managing users Select Manage users to edit, delete, or create operator, maintenance, or installer user accounts. The control panel allows for a maximum of 20 user accounts (all user levels combined). To edit a user account: 1.
  • Page 113 www.acornfiresecurity.com Chapter 3: Configuration and commissioning Secure access Select Secure access to configure the control panel to allow secure or nonsecure access. The default setting is for secure access (all username and password information must be entered at each login). •...

  • Page 114: Commissioning

    www.acornfiresecurity.com Chapter 3: Configuration and commissioning Commissioning After the control panel and corresponding devices are installed and configured, the system must be commissioned. Check the following: • That the fire system is designed in accordance with all required regulations and standards •...
  • Page 115 www.acornfiresecurity.com Chapter 3: Configuration and commissioning ZP2 Series Installation Manual www.acornfiresecurity.com...

  • Page 116: Maintenance

    www.acornfiresecurity.com Chapter 4 Maintenance Summary This chapter includes information on fire alarm system and battery maintenance. Content Fire alarm system maintenance 114 Battery maintenance 115 ZP2 Series Installation Manual www.acornfiresecurity.com...

  • Page 117: Fire Alarm System Maintenance

    www.acornfiresecurity.com Chapter 4: Maintenance Fire alarm system maintenance To ensure correct functioning of your control panel and fire alarm system, and compliance with all European regulations, the following maintenance checks should be followed. Caution: Ensure that fire routing (where configured) has been disabled or that the fire brigade has been notified of any planned fire alarm tests.

  • Page 118: Battery Maintenance

    www.acornfiresecurity.com Chapter 4: Maintenance Battery maintenance The control panel requires two 12 V, rechargeable, sealed lead-acid batteries with 7.2, 12, or 18 Ah capacity. Compatible batteries for this product are shown in Table 65 below. Batteries are located inside the control panel cabinet and must be installed in series.
  • Page 119 www.acornfiresecurity.com Chapter 4: Maintenance Replacing batteries Batteries must be replaced periodically as recommended by the manufacturer. The useful life of the battery is approximately 4 years. Avoid the total discharge of the batteries. Always use the recommended replacement batteries. To replace the batteries: 1.

  • Page 120: Technical Specifications

    www.acornfiresecurity.com Chapter 5 Technical specifications Summary This chapter provides technical specifications for your control panel. Content Loop specifications 118 Power supply specifications 118 Battery and battery charger specifications 119 LCD specifications 120 Communication port specifications 120 Fire network specifications 120 Input and output specifications 120 Internal printer specifications 123 Mechanical and environmental specifications 123...

  • Page 121: Loop Specifications

    Control level voltage 8 VDC ±1 V Resistance 75 Ω max. (based on 3.5 km max. cable length with Ziton protocol 2 mm² diameter for up to 127 devices) 52 Ω max. (26 Ω per wire) 900 Series protocol Capacitance Ziton protocol 700 nF max.

  • Page 122: Battery And Battery Charger Specifications

    www.acornfiresecurity.com Chapter 5: Technical specifications Typical control panel current consumption (with no devices connected) One-loop control panel 135 mA at 24 VDC Two-loop control panel 155 mA at 24 VDC Two-loop control panel with printer 220 mA at 24 VDC Repeater panel 110 mA at 24 VDC Typical expansion board current...

  • Page 123: Lcd Specifications

    www.acornfiresecurity.com Chapter 5: Technical specifications LCD specifications Display type 240 x 128 dot graphic LCD (monochromatic) LCD dimensions (L x W) 83 x 44 mm (active area) Backlight type LED style Backlight colour White Communication port specifications Ethernet Ethernet 10/100BaseT port (10 Mbps) Note: For increased security, we recommend against using Ethernet for remote connection to the control panel via the...
  • Page 124 www.acornfiresecurity.com Chapter 5: Technical specifications Configurable inputs [1] 2 supervised inputs, end-of-line resistor 15 kΩ, 1/4 W Number of inputs 60.2 Ω ≤ active value ≤ 8 kΩ (0.33 to 15 VDC) Active value 10 kΩ ≤ value ≤ 20.2 kΩ (16.1 to 18.9 VDC) Standby value ≤...
  • Page 125 www.acornfiresecurity.com Chapter 5: Technical specifications Fire and fault outputs [1] Output voltage range in 21 to 28 VDC activation Less than −6.1 VDC Output voltage range in short circuit [1] Depending on the current requirements, output cable length restrictions may apply – see “Calculating the maximum output current as a function of the cable length”...

  • Page 126: Internal Printer Specifications

    www.acornfiresecurity.com Chapter 5: Technical specifications Internal printer specifications Note: The internal printer is only available on selected models. Printing method Thermal Resolution 203 dpi (8 dots/mm) Printing speed >50 mm/s Columns 24/40 Paper width 58 mm Paper weight 55 to 70 g/m² Roll dimension Ø...
  • Page 127 www.acornfiresecurity.com Chapter 5: Technical specifications Figure 27: Large cabinet dimensions and views ZP2 Series Installation Manual www.acornfiresecurity.com...
  • Page 128 www.acornfiresecurity.com Chapter 5: Technical specifications Figure 28: Small cabinet dimensions and views ZP2 Series Installation Manual www.acornfiresecurity.com...
  • Page 129 www.acornfiresecurity.com Chapter 5: Technical specifications ZP2 Series Installation Manual www.acornfiresecurity.com...

  • Page 130: Appendix A Default Configurations

    www.acornfiresecurity.com Appendix A Default configurations The following table shows the settings for the default configuration of your panel. Table 67: Default configurations Description Default setting Power supply operation 230 VAC Control panel ID Day/night mode Full day to day mode Control panel network operation Stand-alone Network global commands...
  • Page 131 www.acornfiresecurity.com Appendix A: Default configurations Description Default setting OUT1, OUT2, etc. (Class B) Sounder output (all zones) Fire output Activated by fire alarms in all zones Fault output Follows the General Fault LED and is activated when there is no fault (fail-to-safe) IN1 and IN2 Technical alarm latched (T_AL) Delays...

  • Page 132: Appendix Bpstn Country Codes

    www.acornfiresecurity.com Appendix B PSTN country codes Use the PSTN country codes in the table below when configuring DACT board settings. Table 68: PSTN country codes Country Code Country Code Country Code Algeria Guam Philippines Argentina Hong Kong Poland Armenia Hungary Polynesia Australia Iceland...
  • Page 133 www.acornfiresecurity.com Appendix B: PSTN country codes Country Code Country Code Country Code Dubai Martinique Ukraine Ecuador Mexico Egypt Moldova Uruguay El Salvador Morocco Estonia Netherlands Uzbekistan Finland New Zealand Venezuela France Nigeria Yemen Georgia Norway Zambia Germany Oman Serbia Ghana Pakistan Greece Paraguay...

  • Page 134: Appendix C Menu Maps

    www.acornfiresecurity.com Appendix C Menu maps Fire alarm control panels Maintenance user level Menu level 1 Menu level 2 Menu level 3 Field Setup Zone configuration Test/Disable t_out Panel setup Date and time Day/Night mode Day/Night schedule Holiday calendar Day/Night setup Communications Email accounts Remove USB device...
  • Page 135 www.acornfiresecurity.com Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Reports Event log View all Clear Attention required Revision Firmware revision Configuration revision Serial numbers Contact details Zone status Zone mapping Device status Panel I/O status Output groups status Rules status Firenet status...
  • Page 136 www.acornfiresecurity.com Appendix C: Menu maps Installer user level Menu level 1 Menu level 2 Menu level 3 Field setup Autosetup Loop device configuration Zone configuration General configuration Zone configuration Area configuration Test/Disable t_out Panel I/O configuration Panel inputs Panel outputs Output groups Group configuration Confirmations...
  • Page 137 www.acornfiresecurity.com Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Other settings 24V aux. configuration Fault notifications Buzzer Re-sound sounders Self-test configuration Device LEDs Pulse activation VdS settings Det dirty warning Configuration Restore configuration Load configuration Save configuration Default configuration Expansion boards...
  • Page 138 www.acornfiresecurity.com Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Test Zone test Output test Panel outputs Loop outputs Output group test Locate device Service mode Remote test Diagnostics Individual device Outputs current Power supply Loop values UI test Indicator test Keyboard test...
  • Page 139 www.acornfiresecurity.com Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Rules status Firenet status PAK list Alarm counter Password setup Change password Manage users Secure access Fire alarm repeater panels Maintenance user level Menu level 1 Menu level 2 Menu level 3 Panel setup...
  • Page 140 www.acornfiresecurity.com Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Firenet status Save/Print reports Current events Event log Attention required Panel I/O status Firenet status PAK list Alarm counter Password setup Change password Manage users Installer user level Menu level 1 Menu level 2 Menu level 3...
  • Page 141 www.acornfiresecurity.com Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 SNTP server Other settings 24V aux. configuration Fault notification Buzzer Configuration Restore configuration Load configuration Save configuration Default configuration Expansion boards Load auxiliary files Splash screens Languages Language fonts System update...
  • Page 142 www.acornfiresecurity.com Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Reports Event log View all Clear Attention required Revision Firmware revision Configuration revision Serial numbers Contact details Panel I/O status Firenet status Rules status Save/Print reports Current events Event log Attention required...

This manual is also suitable for:

Zp2 seriesZp2-f1-s-99

Table of Contents