Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Crosley Furniture CO1002A
Summary of Contents for Crosley Furniture CO1002A
- Page 1 C R O S L E Y F U R N I T U R E METAL CHAIR CO1001A...
- Page 2 C R O S L E Y F U R N I T U R E Congratulations! You have purchased a stylish piece of Crosley Furniture. We strive to provide fine furniture products, built with quality materials. Please carefully follow the assembly instructions to ensure your furniture is assembled correctly to provide long lasting enjoyment.
-
Page 3: Part List
PART LIST Chair Back Chair Seat Left leg Right Leg Leg Connector HARDWARE LIST 6.5 X 1.0 MM Short Allen Bolt Long Allen Bolt BOLT COVER 1/4" NUT WASHER 4 PCS 4 PCS 4 PCS 8 PCS 8 PCS FOOT CAP FOOT CAP NUT COVER HEX WRENCH... - Page 4 Step 1: Place the chair seat (B) on a solid flat surface. Position the chair back (A) as shown in (Figure 1) so that the holes in the chair back align with the holes in the chair seat. Insert Short Allen Bolt (1) through the holes of the chair back (A) and then through the holes in the chair seat.
- Page 5 Step 3: The holes in the chair seat/chair back assembly must be perfectly aligned with the holes in the chair leg assembly. While one person holds the chair seat/chair back assembly as shown in (Figure 3), have another person attach to the chair leg assembly.
- Page 6 In accordance with the "Moss-Magnuson Warranty Act" of July 10, 1975, this is termed a "limited warranty" which in no way compromises Crosley Furniture's high standards of Quality and Workmanship. 5 of 5...
- Page 7 C R O S L E Y F U R N I T U R E METAL STATIONARY LOVESEAT CO1002A...
- Page 8 C R O S L E Y F U R N I T U R E Congratulations! You have purchased a stylish piece of Crosley Furniture. We strive to provide fine furniture products, built with quality materials. Please carefully follow the assembly instructions to ensure your furniture is assembled correctly to provide long lasting enjoyment.
- Page 9 PART LIST Upper Back Crossbar Chair Back Chair Seat Lower Back Crossbar 2PCS 2PCS 2PCS Front Crossbar HARDWARE LIST 1/4" X 15 MM BOLT 1/4" X 25MM BOLT 1/4" X 32MM BOLT 1/4" X 40MM BOLT 1/4" X 42MM BOLT 8 PCS 1 PC 1 PC...
- Page 10 Step 1: Place the chair seat (B) on a solid flat surface. Position the chair back (A) as shown in (Figure 1) so that the holes in the chair back align with the holes in the chair seat. Insert 1/4"x15mm bolts (1) through the holes of the chair back (A) and then through the holes in the chair seat.
- Page 11 Step 4: Attach arm ( C) to seat (B) and back (A) using 1/4"x42mm bolts (5), two 6.5 x 1.0 washers (6), and 1/4" nuts (7) as shown in (Figure 4). Tighten with hex wrench (12) and Allen Key (13). Do not over tighten. Repeat for remaining Loveseat arm.
- Page 12 In accordance with the "Moss-Magnuson Warranty Act" of July 10, 1975, this is termed a "limited warranty" which in no way compromises Crosley Furniture's high standards of Quality and Workmanship. 5 of 5...
- Page 13 C R O S L E Y F U R N I T U R E METAL SIDE TABLE CO1011A...
- Page 14 C R O S L E Y F U R N I T U R E Congratulations! You have purchased a stylish piece of Crosley Furniture. We strive to provide fine furniture products, built with quality materials. Please carefully follow the assembly instructions to ensure your furniture is assembled correctly to provide long lasting enjoyment.
- Page 15 PART LIST Leg Connector HARDWARE LIST ST4.2 X 33 MM 6.5 X 1.0 MM 1/4" X 15 MM BOLT BOLT COVER 1/4" NUT WASHER BOLT 3 PCS 3 PCS 3 PCS 3 PCS 6 PCS FOOT CAP HEX WRENCH Allen Wrench FACTORY ASSEMBLY 1 PC 1 PC...
- Page 16 Step1: Place tabletop upside down on a flat, non-abrasive surface. Attach table leg to tabletop using 1/4"x 15mm bolt (1) and 1/4" (2) washer as shown in (Figure 1). Add 1/4" nut (4) to the end of bolt. Tighten a few revolutions only. Do not tighten completely at this time as some adjustments may be necessary to the alignment of the table legs.
- Page 17 Step3: Make any adjustments to the parts to ensure they are properly aligned. At this time tighten all nuts and bolts using Allen Wrench (6) and hex wrench (7). Tighten each bolt connection a few revolutions at a time, rotating between bolt connections until all nuts and bolts are completely tightened.
- Page 18 In accordance with the "Moss-Magnuson Warranty Act" of July 10, 1975, this is termed a "limited warranty" which in no way compromises Crosley Furniture's high standards of Quality and Workmanship. 5 of 5...
- Page 21 Leg Coupler Allen Wrench Allen Bolt Square Nut Flat Washer...
- Page 22 Insert Square Nuts (Part #3) into position in both of the Leg Couplers (C). Note - Be sure that the square nuts are completely inserted to the bottom of leg coupler. - Attach the Leg Coupler (C) to two of the Legs (B) using Allen Bolts (Part #1) &...
- Page 23 - Lay the Top (A) on a flat surface with the bottom lip facing up. Fit the flat ends of the legs under the lip of Top (A) aligning the hole of the Leg Coupler (C) with the hole in Top (A). - Add a third Leg (B) fitting the flat end under the lip of Top (A) and attach using an Allen Bolt (Part #1) and Flat Washer (Part #2) as shown.
- Page 24 - Attach the second Leg Coupler (C) to the three Legs (B) using Allen Bolts (Part #1) & Flat Washers (Part #2) as shown. - Add the fourth Leg (B) by fitting the flat end of the leg under the lip of the table and positioning the portion with the bolt holes into the Leg Coupler (C).
- Page 25 - Attach the fourth Leg (B) to the Leg Coupler (C) using Allen Bolts (Part #1) and Flat Washers (Part #2) as shown. Note - Be sure that the legs are aligned at 90 degree angles before tightening the fourth leg completely. - Turn the table over on a flat surface.
Need help?
Do you have a question about the CO1002A and is the answer not in the manual?
Questions and answers