Related Manuals for Para systems MINUTEMAN Endeavor Series
Summary of Contents for Para systems MINUTEMAN Endeavor Series
- Page 1 Endeavor Series Battery Pack User’s Manual Endeavor Series minutemanups.com | 800.238.7272...
-
Page 3: Table Of Contents
Table of Contents Introduction ………………………………………………………………… 1 Installation ………………………………………………………………….. 3 Connecting to a UPS…………………………………………………….. 6 Replacing the Battery Module………………………………………. 8 Obtaining Service ………………………………………………………… 10 Specifications ………………………………………………………………. 11 Warranty ……………………………………………………………………… 12 minutemanups.com | 800.238.7272... -
Page 4: Introduction
ONLY and must adhere to all local electrical codes. Any changes or modifications made to this unit, without expressed written permission from Para Systems, Inc. will void the warranty of the product. This Battery Pack module is only intended to be installed in an indoor, temperature-controlled environment that is free of conductive contaminants, dust or direct sunlight. - Page 5 The ambient operating temperature range for this device is 32° ~ 104°F (0° ~ 40°C). To ensure the proper ventilation and cooling of the UPS, do not block any of the ventilation cutouts in the case. Adequate space must be provided around all sides of the Battery Pack to allow for proper air flow. Do not mount the device with its front or rear panel facing down at any angle.
-
Page 6: Installation
Life Support Policy: As a general policy, Para Systems does not recommend the use of any of our products in life support applications where failure or malfunction of the product can be reasonably expected to cause failure of the life support device or to significantly affect its safety or effectiveness. - Page 7 Receiving Inspection: Once the product arrives, it should be visually inspected for any damage that may have occurred in shipping. Immediately notify the carrier and place of purchase if any damage is found. Warranty claims for damage caused by the carrier are the responsibility of the purchaser. The product packing materials were carefully designed to meet ISTA 1A and minimize any potential shipping damage.
- Page 8 Tower Installation: Use caution as the Battery Pack is very heavy. Two or more individuals are recommended for installation. 1. Locate the UPS to its final installation location. 2. Orient the Battery Pack vertically with the nameplate in line with the UPS. 3.
-
Page 9: Connecting To A Ups
Battery Pack Rear Panels: BP192V5CRTXL BP192V10CRTXL DC Breaker – Overcurrent Protection AC Output Battery Pack Detection Port AC Input AC Circuit Breaker CD Connector (to UPS or 2 Battery Pack) Connecting to a UPS All wiring used for the installation of the UPS must be in accordance with the local electrical codes and regulations and performed using the following instructions by a licensed electrician. - Page 10 Charging the Battery These Battery Packs will charge the internal batteries whenever the Battery Pack is connected to an AC source and there is an acceptable AC voltage present (100 - 240VAC). It is recommended that the Battery Packs be charged for a minimum of 4 hours before use. The Battery Pack maybe used immediately, however, the “On-Battery”...
-
Page 11: Replacing The Battery Module
9. Connect one end of the second External Battery Detection cable to the bottom External Battery Detection Port on the rear panel of the first Battery Pack. 10. Connect the other end of the second External Battery Detection cable to the top External Battery Detection Port on the rear panel of the second Battery Pack. - Page 12 To maintain the optimal performance of the Endeavor UPS, it is important to only use battery modules designed to work with the series. Using third-party or inferior batteries will affect the negatively affect the performance and life of the UPS. Replacement battery modules are available from Minuteman at https://minutemanups.com/buy-ups- replacement-batteries/ or by contacting Minuteman service at 800.238.7272.
-
Page 13: Obtaining Service
Figure 7 1) Remove the front panel of the battery pack by pulling from each end, directly away from the metal case. (Figure 1) 2) Separate the black Anderson connectors for the battery modules. (Figure 2) 3) Using a Philips screwdriver, loosen and remove the battery retention bracket by turning screws counterclockwise until they release from the battery cage. -
Page 14: Specifications
4) Mark the RMA # on the outside of all packages. The factory cannot accept any package without the RMA # marked on the outside. 5) Return the unit by insured, prepaid carrier to: Para Systems Inc. MINUTEMAN UPS 2425 Technical Drive... -
Page 15: Warranty
No employee, salesman, or agent of Para Systems is authorized to add to or vary the terms of this warranty. Please go to our website at www.minutemanups.com/warranty/ to fill out the Warranty Registration. - Page 16 Life Support Policy Para Systems does not support the use of any of its products in life support applications where the failure or malfunction of the product can be reasonably expected to cause failure to life support devices or to significantly affect their safety or effectiveness.
Need help?
Do you have a question about the MINUTEMAN Endeavor Series and is the answer not in the manual?
Questions and answers