Advertisement

GENUINE CAR-NAVIGATION UNIT
INSTALLATION INSTRUCTIONS
Thank you for purchasing a genuine Mazda accessory.
Before removal and installation, be sure to thoroughly read these instructions.
Please read the contents of this booklet in order to properly install and use the
car-navigation unit. Your safety depends on it.
Keep these instructions with your vehicle records for future reference.
• There are several
safety when installing or removing the car-navigation unit. Always read and follow them
in order to prevent injuries, accidents, and possible damage to the vehicle.
WARNING: Indicates a situation in which serious injury or death could result if
the warning is ignored.
CAUTION: Indicates a situation in which bodily injury or damage to the vehicle
could result if the caution is ignored.
• For areas indicating the tightening torque in this instruction manual, tighten to the
specified torque using a torque wrench. For areas in which the tightening torque is
indicated inside parentheses ( ), the tightening torque is indicated as a reference value,
however tightening using a torque wrench is not necessary.
• Do not modify the car-navigation unit.
• Do not install the car-navigation unit in any way other than described in the following
instructions.
• If in any doubt, please ask your Mazda dealer to install the accessory in order to
prevent errors in installation.
• If you have any questions about the use of the accessory, ask your Mazda dealer for
proper advice before using it.
• Mazda and its suppliers are not responsible for injuries, accidents, and damage to
persons and property that arise from the failure of the dealer or installer to follow these
instructions.
To ensure safety and reliability of the work, installation, removal and disposal work
must be carried out by an Authorized Mazda Dealership.
Be careful not to lose removed parts, and be sure that they are kept free from
scratches, grease or other dirt.
PART NUMBER: GHY9 79 EZX (LHD)
NOTE
To the dealer
• Please turn over these instructions to the customer after installation.
To the customer
• Keep these instructions after installation. The instructions may be necessary
for installing other optional parts or removal of this accessory.
• Should the vehicle or this accessory be resold, always leave these instructions
with it for the next owner.
WARNING
WARNING and
CAUTION sections in this booklet concerning
PART NAME: CAR-NAVIGATION UNIT
GJY7 79 EZX (RHD)
VEHICLE: MAZDA6
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GHY9 79 EZX and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Mazda GHY9 79 EZX

  • Page 1 • Do not install the car-navigation unit in any way other than described in the following instructions. • If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation. • If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before using it.
  • Page 2: Parts List

    ▼ PARTS LIST NOTE: • Before installation, verify that the kit includes all the following parts and that they are free of dirt, scratches, or damage. • GHY9 79 EZX (LHD), GJY7 79 EZX (RHD) Part Part name Qty. Part Part name Qty.
  • Page 3: Installation

    3. VEHICLE PARTS REMOVAL NOTE: The following vehicle parts removal procedure is for left-hand drive vehicles. Perform the same procedure for right-hand drive vehicles. Negative battery cable disconnection 1. Set the selector lever to P range. (AT vehicles only) WARNING •...
  • Page 4 GPS Antenna Installation GPS Antenna Screw connector 1. Install the GPS antenna and secure it using a screw (1) as shown in the figure. Tightening torque: (1.3 –1.5 N・m) 2. Connect the GPS antenna connector. 3. Install the speaker grille. 4.
  • Page 5 LH steering wheel only 4. Remove the wiring harness clips (2) on the back of the pocket assy (LH steering wheel only) Harness clips • Be careful not to apply excessive force to the wiring harness when removing the connectors. •...
  • Page 6 3. Press the clips (4 locations) shown in the figure and install the Car-navigation unit car-navigation unit to the lower panel. CAUTION • Be careful not to press the car-navigation unit when Clips Clips Clips installing it. Clips Lower panel 4.
  • Page 7: Operation Check

    5. OPERATION CHECK 1. Connect the negative battery cable and perform an operation check by referring to the owner’s manual applicable to the vehicle. 2. If there is any malfunction, disconnect the negative battery cable and verify that each connector is properly connected and the wiring harnesses are not damaged or pinched, then perform the operation check again.
  • Page 8 After switching to the Vehicle and Navi Signal Check screen, touch “ “on the screen to switch the display screen to “NAVI GPS ANT”. Verify that “NAVI GPS ANT: OK” is displayed. If not OK, verify the connection condition again. Press the POWER/VOLUME dial to switch to the AUDIO screen.
  • Page 9 (Vehicles with i-stop) Negative battery cable Switch the ignition off. Current Remove the negative battery cable. sensor connector • It is necessary to reset after this procedure. It is reset by removing the negative battery cable. Disconnect the current sensor connector. Wait for 10s or more after installing the negative battery cable Tightening torque: 4.0-6.0 N・m...
  • Page 10 4. Touch “Yes”. 5. Touch “I agree”. 6. Touch the screen. 7. Touch “Setting”. 8. Touch the location shown in the figure.
  • Page 11 9. Touch “Reset factory setting”. 10. Touch “Yes”. 11. Touch “Yes”. 12. Setting is finished when “Welcome” screen appears. 13. Switch the ignition off.
  • Page 12 Date Car-navigation unit INSTALLATION MAZDA6 INSPECTION GHY9 79 EZX (LHD) SHEET GJY7 79 EZX (RHD) Perform the following inspections Check 1. Inspection items after installation • Verify the fitting between the vehicle part and the installed part, and inspect for damage or dirt.

This manual is also suitable for:

Gjy7 79 ezxGhy9-79-ezxd

Table of Contents