Advertisement
Table of Contents
Advertisement
Table of Contents
Related Manuals for HH Electronics TESSEN INSTALL TNi-WPRO Series
Summary of Contents for HH Electronics TESSEN INSTALL TNi-WPRO Series
- Page 1 TNi-WPRO SERIES CABINETS USER MANUAL...
- Page 2 OVERVIEW The TNi-WPRO range comprises four sizes of high-power, 2-way, full-range loudspeakers ideally suited for environments where a higher SPL is required. Each TNi-WPRO model features a high- performance HH-designed low-frequency driver paired with a Celestion high-frequency compression driver. The custom-designed rotatable waveguide makes the TNi-WPRO series even more versatile, allowing for vertical or horizontal orientation with a 90°(H) x 60°(V) dispersion angle.
-
Page 3: Installation
INSTALLATION WALL BRACKET All cabinets in the TNi-WPRO range have four rear mounted M8 fixing points for use with the HH TNi- BRK30 wall bracket (sold separately) or other compatible hardware. TNi-BRK30 provides a solid, adjustable angle fixing in either horizontal or vertical installations and is available in either black or white finishes. - Page 4 SUSPENSION The TNi-WPRO cabinets come equipped with 7x M10 suspension points pre-fitted with travel bolts. These may be removed, and eye bolts inserted for flying cabinets. M10 eye bolts (not included) must be high quality forged shouldered type fittings specifically rated for the purpose. A minimum thread length of 30mm is mandatory.
- Page 5 LOGO ORIENTATION The logo may be rotated depending on your chosen installation orientation. Gently twist to your preferred orientation. The included spring locks will snap to 90-degree increments and hold firmly in place. Page 4...
- Page 6 WAVE GUIDE ORIENTATION The custom-designed waveguide may be rotated to suite your dispersion requirements. To access the waveguide, the front grille must first be removed by unscrewing the grille mounting screws indicated below. Next remove the waveguide by unscrewing the 8 waveguide screws and set to required orientation. There is no need to remove the horn entirely, just enough for it to be rotated.
- Page 7 CONNECTIONS The TNi-WPRO loudspeaker range is fitted with both with Euroblock and M4 screw input/output terminals. The I/O connections are wired in parallel so can be interchanged or used to link additional cabinets. Page 6...
- Page 8 WIRING Follow these steps when wiring up a Euroblock connector. You will need a flathead screwdriver with a 1.2mm or smaller head, as well as wire strippers (not provided). 1. Strip back the wire insulation using wire strippers, leaving around 7-10mm of exposed cable to allow ample wire to go into the plug.
-
Page 9: Specifications
SPECIFICATIONS TNi-W8PRO Specifications Model TNi-W8PRO System type 2-Way Full Range Passive Loudspeaker, 8" LF, Bass Reflex Woofer Size 8" Black 20050-8 HH Designed High Performance Driver, 2.0" Voice Coil Tweeter Size 1.0" Celestion CDX1-1070 Nominal System Impedance 8 ohm Power Rating 200W AES, 400W Continuous, 800W Peak Recommended Amplifier HH M-Series M-750D or equivalent with 400-800W @ 8 Ohms... - Page 10 TNi-W10PRO Specifications Model TNi-W10PRO System type 2-Way Full Range Passive Loudspeaker, 10" LF, Bass Reflex Woofer Size 10" Black 25050-8 HH Designed High Performance Driver, 2.0" Voice Coil Tweeter Size 1.4" Celestion CDX1-1445 Nominal System Impedance 8 ohms Power Rating 250W AES, 500W Continuous, 1000W Peak Recommended Amplifier HH M-Series M-750D or M-1500D or equivalent with 500-1000W @ 8 Ohms...
- Page 11 TNi-W12PRO Specifications Model TNi-W12PRO System type 2-Way Full Range Passive Loudpeaker, 12" LF, Bass Reflex Woofer Size 12" Black 30065-8 HH Designed High Performance Driver, 2.5" Voice Coil Tweeter Size 1.4" Celestion CDX1-1445 Nominal System Impedance 8 ohm Power Rating 300W AES, 600W Continuous, 1200W Peak Recommended Amplifier HH M-Series M-750D or M-1500D or equivalent with 600-1200W @ 8 Ohms...
- Page 12 TNi-W15PRO Specifications Model TNi-W15PRO System type 2-Way Full Range Passive Loudspeaker, 15" LF, Bass Reflex Woofer Size 15" Black 38080-8 HH Designed High Performance Driver, 3.0" Voice Coil Tweeter Size 1.75" Celestion CDX1-1742 Nominal System Impedance 8 ohms Power Rating 450W AES, 900W Continuous, 1800W Peak Recommended Amplifier HH M-Series M1500D or equivalent with 600-1200W @ 8 Ohms...
- Page 13 DIMENSIONS TNi-W8PRO Page 12...
- Page 14 TNi-W10PRO Page 13...
- Page 15 TNi-W12PRO Page 14...
- Page 16 TNi-W15PRO Page 15...
-
Page 17: Safety And Warnings
SAFETY AND WARNINGS To take full advantage of your new product and enjoy long and trouble-free performance, please read this owner's manual carefully, and keep it in a safe place for future reference. 1) Unpacking: On unpacking your product, please check carefully for any signs of damage that may have occurred whilst in transit from the HH factory to your dealer. - Page 18 Intended to alert the user to the presence of uninsulated ‘Dangerous Voltage’ within the products enclosure that may be sufficient to constitute a risk of electrical shock to persons. Ce symbole est utilisé pur indiquer à l’utilisateur de ce produit de tension non-isolée dangereuse pouvant être d’intensité...
- Page 19 HH AUDIO STEELPARK ROAD, COOMBSWOOD BUSINESS PARK WEST, HALESOWEN, B62 8HD HH AUDIO PART OF HEADSTOCK GROUP FOR THE LATEST INFORMATION PLEASE VISIT WWW.HHAUDIO.COM IN THE INTEREST OF CONTINUED DEVELOPMENT, HH RESERVES THE RIGHT TO AMEND PRODUCT SPECIFICATION WITHOUT PRIOR NOTIFICATION. V0.1 Page 18...
Need help?
Do you have a question about the TESSEN INSTALL TNi-WPRO Series and is the answer not in the manual?
Questions and answers