Appropriate Installation Location; Removing Packaging Reinforcement; Connecting Water Supply; Removing The Transportation Locks - Beko WMB 51021 CS PT Manual

2 Installation
Refer to the nearest Authorised Service Agent for
installation of the product. To make the product
ready for use, review the information in the
user manual and make sure that the electricity,
tap water supply and water drainage systems
are appropriate before calling the Authorized
Service Agent. If they are not, call a qualified
technician and plumber to have any necessary
arrangements carried out.
Preparation of the location and electrical,
C
tap water and waste water installations at
the place of installation is under customer's
responsibility.
Installation and electrical connections of
B
the product must be carried out by the
Authorized Service Agent. Manufacturer shall
not be held liable for damages that may arise
from procedures carried out by unauthorized
persons.
Prior to installation, visually check if the
A
product has any defects on it. If so, do not
have it installed. Damaged products cause
risks for your safety.
Make sure that the water inlet and discharge
C
hoses as well as the power cable are not
folded, pinched or crushed while pushing
the product into its place after installation or
cleaning procedures.

Appropriate installation location

• Place the machine on a rigid floor. Do not
place it on a long pile rug or similar surfaces.
• Total weight of the washing machine and the
dryer -with full load- when they are placed
on top of each other reaches to approx.
180 kilograms. Place the product on a solid
and flat floor that has sufficient load carrying
capacity!
• Do not place the product on the power
cable.
• Do not install the product at places where
temperature may fall below 0ºC.
• Place the product at least 1 cm away from
the edges of other furniture.

Removing packaging reinforcement

Tilt the machine backwards to remove the
packaging reinforcement. Remove the packaging
reinforcement by pulling the ribbon.

Removing the transportation locks

Do not remove the transportation
A
locks before taking out the packaging
reinforcement.
Remove the transportation safety bolts
A
before operating the washing machine,
otherwise, the product will be damaged.
1. Loosen all the bolts with a spanner until they
rotate freely.
2. Remove transportation safety bolts by
turning them gently.
3. Attach the covers supplied in the User
Manual bag into the holes on the rear panel.
Keep the transportation safety bolts in a safe
C
place to reuse when the washing machine
needs to be moved again in the future.
Never move the product without the
C
transportation safety bolts properly fixed in
place!

Connecting water supply

The water supply pressure required to run
C
the product is between 1 to 10 bars (0.1 – 1
MPa). It is necessary to have 10 – 80 liters of
water flowing from the fully open tap in one
minute to have your machine run smoothly.
Attach a pressure reducing valve if water
pressure is higher.
If you are going to use the double water-inlet
C
product as a single (cold) water-inlet unit,
you must install the supplied stopper to the
hot water valve before operating the product.
(Applies for the products supplied with a
blind stopper group.)
If you want to use both water inlets of the
C
product, connect the hot water hose after
removing the stopper and gasket group from
the hot water valve. (Applies for the products
supplied with a blind stopper group.)
Models with a single water inlet should not
A
be connected to the hot water tap. In such
a case the laundry will get damaged or the
product will switch to protection mode and
will not operate.
Do not use old or used water inlet hoses
A
on the new product. It may cause stains on
your laundry.
1. Connect the special hoses supplied with the
product to the water inlets on the product.
Red hose (left) (max. 90 ºC) is for hot water
inlet, blue hose (right) (max. 25 ºC) is for cold
water inlet.
Ensure that the cold and hot water
A
connections are made correctly when
installing the product. Otherwise, your
laundry will come out hot at the end of the
washing process and wear out.
3
EN