Loading Door Lock; Child Lock; Progress Of Programme; Changing The Selections After Programme Has Started - Beko WMB 51021 CS PT Manual

lights and indicators will turn off. Once the
Programme Selection knob is rotated or
any button is pressed, indicator lights and
indicators will turn on again.

Child Lock

Use child lock function to prevent children from
tampering with the machine. Thus you can avoid
any changes in a running programme.
If the Programme Selection knob is rotated
C
when the child lock is active, the lights on the
1 and 2 auxiliary function buttons will blink
st nd
3 times. The child lock does not allow any
change in the programmes and the selected
temperature, speed and auxiliary functions.
Even if another programme is selected with
C
the Programme Selection knob while the
Child Lock is active, previously selected
programme will continue running.
When the Child Lock is active and the
C
machine is running, you can switch the
machine to Pause mode without deactivating
the Child Lock by turning the Programme
Selection knob to On / Off position. When
you turn the Programme Selection knob
afterwards, the programme will resume.
To activate the Child Lock:
1. Press and hold 1 and 2
st
buttons for 3 seconds. The lights on the 1
2 Auxiliary Function buttons will flash while you
nd
keep the buttons pressed for 3 seconds.
To deactivate the Child Lock:
Press and hold 1 and 2
st
buttons for 3 seconds while any programme is
running. The lights on the 1
Function buttons will flash while you keep the
buttons pressed for 3 seconds.
In addition to the method above, to
C
deactivate the Child Lock, switch the
Programme Selection knob to On / Off
position when no programme is running, and
select another programme.
When the power is restored after a power
C
failure or after your machine is unplugged
and plugged in again, the Child Lock will not
be deactivated when the machine resumes
operating.

Progress of programme

Progress of a running programme can be
followed from the Programme Follow-up indicator.
At the beginning of every programme step, the
relevant indicator light will turn on and light of the
completed step will turn off.
You can change the auxiliary functions, speed
and temperature settings without stopping the
programme flow while the programme is running.
To do this, the change you are going to make
must be in a step after the running programme
step. If the change is not compatible, relevant
lights will flash for 3 times.
Auxiliary Function
nd
and
st
auxiliary function
nd
and 2 Auxiliary
st nd
If the machine does not pass to the spinning
C
step, Rinse Hold function might be active
or the automatic unbalanced load detection
system might be activated due to the
unbalanced distribution of the laundry in the
machine.

Loading door lock

There is a locking system on the loading door of
the machine that prevents opening of the door in
cases when the water level is unsuitable.
Loading door light will start flashing when the
machine is switched to Pause mode. Machine
checks the level of the water inside. If the level is
suitable, Loading Door light illuminates steadily
within 1-2 minutes and the loading door can be
opened.
If the level is unsuitable, Loading Door light turns
off and the loading door cannot be opened. If
you are obliged to open the Loading Door while
the Loading Door light is off, you have to cancel
the current programme; see "Canceling the
programme".
Changing the selections after
programme has started
Switching the machine to pause mode
Press the Start/Pause button to switch the
machine to pause mode while a programme is
running. The light of the step which the machine
is in starts flashing in the Programme Follow-up
indicator to show that the machine has been
switched to the pause mode.
Also, when the loading door is ready to be
opened, Loading Door light will also illuminate
continuously in addition to the programme step
light.
Changing the speed and temperature
settings for auxiliary functions
Depending on the step the programme has
reached, you may cancel or activate the auxiliary
functions; see, "Auxiliary function selection".
You may also change the speed and temperature
settings; see, "Spin speed selection" and
"Temperature selection".
If no change is allowed, the relevant light will
C
flash for 3 times.
Adding or taking out laundry
Press the Start/Pause button to switch the
machine to pause mode. The programme follow-
up light of the relevant step during which the
machine was switched into the pause mode will
flash. Wait until the Loading Door can be opened.
Open the Loading Door and add or take out the
laundry. Close the loading door. Make changes
in auxiliary functions, temperature and speed
settings if necessary. Press Start/Pause button to
start the machine.
12
EN