Table of Contents
Advertisement
Quick Links
SHENZHEN ATESS POWER TECHNOLOGY CO.,LTD
GROWATT-ATESS Industrial Park, No.23 Zhulongtian Road, Shuitian Community,
Shiyan Street, Baoan District, Shenzhen
+86 755 2998 8492
T
E
info@atesspower.com
W
www.atesspower.com
Revised date: 2024-01-09
ATESS EVC-AC22S/DC200D-X
AC/DC charging equipment user manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ATESS EVC-AC22S
Summary of Contents for ATESS EVC-AC22S
- Page 1 ATESS EVC-AC22S/DC200D-X SHENZHEN ATESS POWER TECHNOLOGY CO.,LTD GROWATT-ATESS Industrial Park, No.23 Zhulongtian Road, Shuitian Community, Shiyan Street, Baoan District, Shenzhen AC/DC charging equipment user manual +86 755 2998 8492 info@atesspower.com www.atesspower.com Revised date: 2024-01-09...
- Page 2 This user manual is copyrighted by Shenzhen ATESS Power Technology Co., EVC series intelligent AC/DC charging equipment is a device that provides high- Ltd. (hereinafter referred to as “ATESS Power Technology”). No unit or individual efficiency, safe and stable AC/DC power supply for electric vehicles, which has a...
-
Page 3: Table Of Contents
Contents Product description Specification Packaging list Appendix 7.1 Electric diagram 7.2 Module installation Installation and wiring 7.3 Warranty 3.1 Installation conditions 7.4 Contact 3.2 Cable connection Parameter configuration 4.1 System Parameters 4.2 Network parameters 4.3 Protection parameters Operation instruction and LCD introduction 5.1 Charging mode and operation 5.2 LCD interface introduction 5.3 Troubleshooting... - Page 4 . Product description Crimp the below shown ring terminals on the end of the AC input wires and PE wires. Connect the wires into the terminal block of the chargepoint as below. Check the wiring then close the switch and the door. 1.Auxiliary power control breaker;...
-
Page 5: Installation Conditions
. Packaging list 2) The charger must be installed on a customized concrete foundation, the foundation is as below: Items Remark Charging equipment User manual Certificate of quality User card Hexagon head bolt, all thread,M12*90/GB5783, blue zinc plating Plain Washer,D12/GB97 1, plated blue zinc Standard Spring Washer,D12/GB93, plated blue zinc Hexagon Nuts,M12/GB6170, electro plated blue zinc . -
Page 6: Cable Connection
3.2 Cable connection . Parameter configuration Connect the buried three phase four wire AC cables to the input terminal of the charger with correct color order and phase sequence. The earth cable shall be After installed and connected, the charging equipment must first be configured connected to the grounding bar of the charger. -
Page 7: System Parameters
4.1 System Parameters Function description Parameters Charging mode setting. 1 is APP mode; 2 is RFID Charge type mode; 3 is Plug&charge mode Language setting. Currently support English and Language set France dual language display. Charge model (already preset in factory) Charge model (already preset in factory) After changing parameters, click the “Set”... -
Page 8: Protection Parameters
4.3 Protection parameters Function description Parameters The protection-related parameters, such as voltage, current, temperature, power, etc. Server address setting, used to set domain or IP Server URL1 address of back-office server. Address of backup server. This parameter is not Server URL2 available now, reserved for future use. -
Page 9: Charging Mode And Operation
4.4 Plug type RFID mode: Charging can only be initiated or ceased by swiping RFID card. There are ComboCCS2 and Type 2 two kind of plugs optional. RFID mode operation process flow . Operation instruction and LCD introduction Plug&Charge: Charging will start automatically after EV plugged in. If you want to stop the charging, just press the stop icon on the screen. -
Page 10: Lcd Interface Introduction
5.2 LCD interface introduction The charging equipment is equipped with a 7 inch industrial-grade resistor type touch panel. The display content is as below, System parameters page. When powered up, the charging equipment will show this display Network parameters page, used to set network related parameters of back-office server and the charging equipment. -
Page 11: Troubleshooting
5.3 Troubleshooting . Specification Fault description Model EVC-AC22S/DC200D-X Emergency stop is pressed! Dimension(mm) 787*800*1885(W*D*H) RFID communication fault! Weight(kg) 240-310kg Display Over temperature fault! Casing material Stainless steel&acrylic sheet Lightning protection fault! AC input Power module communication fault! 400V, 3 phase 5 wires... -
Page 12: Electric Diagram
. Appendix IP degree IP54 Working environment -25℃~50℃ Relative humidity <95％ 7.1 Electric diagram Altitude ≤2000m, derate for higher than 2000m 400V/AC input Cooling method Forced air cooling Remote monitoring Ethernet/WIFI/4G/485/232 Payment RFID/APP 200k 120k 160k Standby power Standards IEC-62196-2;EN61851 Mounting Ground Certificate... -
Page 13: Module Installation
7.2 Module installation ①. Press ▲ or ▼ to switch the current display to the information interface to be changed. 1.Module installation position: ②. Press ▲ or ▼ about 2.5 seconds after release, you can see the display flashing. ③. Press ▲ or ▼ to change the settings. ④. -
Page 14: Warranty
For warranty cases during the warranty period, the customer should present the Address: GROWATT-ATESS Industrial Park,No.23 Zhulongtian Road,Shuitian invoice of the purchase of the product to the service personnel of ATESS. At the Community,Shiyan Street,Baoan District,Shenzhen same time, the nameplate on the product should be clearly visible, otherwise the warranty claim might not be accepted.
Need help?
Do you have a question about the EVC-AC22S and is the answer not in the manual?
Questions and answers