Do you have a question about the YM-PREDATOR and is the answer not in the manual?
Questions and answers
Danny zavolta
August 1, 2025
Um I'm wondering what the magnaton setting is even for if you could explain that more for me because I have looked everywhere and haven't been able to find anything about it hahah thank you.
WARNING! Ø Please conduct a thorough inspection of your scooter before riding. Always wear protective gear. Ø Abide by local laws, regulations, and speed limits. INSPECTION BEFORE RIDING Turn on the control panel. Make sure the brakes work properly and brake pads are not worn excessively.
SAFETY PRECAUTIONS A. Always wear a helmet,knee pads and elbow pads when riding. B. Use low speeds initially, and gradually increase to higher speeds after as skills and confidence improve. C. Do not ride in the rain or through water puddles D.
STRUCTURE PARAMETER PERFORMANCE Maximum Speed 63 Mph (100Km/h) Maximum Range 100 Miles (160km dual motors mode)* Motor Power 4000W*2 dual motors with hall sensor Speed Modes 3 Gears x 2 Drives Charging Time 6-7 hours Battery Capacity 72V 50Ah Water Resistance IP 54 for the whole scooter Wheel Size 13 inch Tubeless Off Road Tire...
PACKING LIST - 2 l Battery l Thumb Throttle l User Manual (backup) l YUME Bag(gift) & Tools l Dampener l 2 NFC Keys l 2 Chargers l Stem Light Remote Remarks: Package 2 of the delivery list includes batteries, battery boxes and accessories.
Page 10
SCOOTER ASSEMBLY Unfolding Unbox your scooter 1. Now that your scooter is out of the Unseal the box using a box cutter. Inside the box, you should find a box, locate the head bar. protective styrofoam, in which 2. Lift the head bar up until the bar is your scooter is.
BATTERY ASSEMBLY ① Loosen the deck cover screw and ② Carefully place the battery into remove the deck plate. the battery box of the scooter. Be sure not to pinch any wires. ④ Turn on the two load switches as ③...
Page 12
SCOOTER ASSEMBLY Command Centre Installation ② Make sure the light switch, ① Check that the LCD control indicator light switch/horn and panel and display button screws display switch screws are tight. are tight. ③ Check that the left and right ④...
SCOOTER ASSEMBLY Kickstand Installation ① Predator kickstand ② Remove the top two screws at the kickstand mounting location. ③ Align the kickstand with the screw holes, and tighten the screws.
SCOOTER ASSEMBLY Kickstand Installation ④ Kickstand installation is now complete. Rear Fender Installation ①Align the rear fender bracket parallel to the screw holes, and then use the corresponding screws in the corresponding screw holes to install it. ②Align the rear fender bracket with the screw holes, and tighten the screws.
DAMPER ASSEMBLY Install the Dampener (1) Make sure the scooter is pointing straight during the installation. (2) Loosen screws "a" on the (3) Attach the bracket "3" as dampener clamp "2" with a hex shown in the photo above. wrench, and then slide dampener "1"...
Page 16
DAMPER ASSEMBLY Install the Dampener (4) Tighten the locking screw on the bracket "3". (5) Attach joint "b" on the dampener assembly to the bracket "3" and fasten as shown. (6) Attach the dampener to the mount "4" via the fixing bolt in "c".
Page 17
DAMPER ASSEMBLY Install the Dampener (7) While keeping the front tire straight, slide the center rod of the dampener so the exposed ends are equal in length. (8) After aligning the dampener and making suitable adjustments, tighten the fixing bolt "a". (9) Check that the front wheel turns freely.
CHARGING OPERATION 1. First, ensure that the two parts of the charger (i.e. the AC wall plug/power cord and the transformer) are firmly connected. 2. Next, locate the three-pin connector on one end of the charger. Open up the charging port’s cover to spot the charging hole.
COOLING SYSTEM OPERATION Instructions for use: The cooling system display is located under the deck and has already been present with all the necessary parameters at the factory. No changes are necessary. However, this manual will guide you in configuring the presets if you choose to tweak it. After turning on the scooter, the thermostat displays the current temperature of the controller.
Page 20
CHRGING&HANDLEBAR SECTION GET TO KNOW THE HANDLEBAR OF YOUR E-SCOOTER LCD Control Panel Display Button Turning Light Thumb Throttle Light Switch Switch/Horn...
POLE FOLDING OPERATION Folding 2. Unlock the 3. Turn the foldable frame by 1. Get to know the foldable frame to first turning it foldable frame. unlock it. outward to unlock the folding lever. 6. Continue folding until 4. Then lift up the 5.
The password default password is: 1111(YUME RIDE application setting can change the password ). a. After turning the scooter on, place the NFC key near the display's NFC sensor to automatically unlock the scooter.
DISPLAY BUTTON Button Name Function Press and hold the [Power Button] for 3 seconds to switch on or off. Press the [Power Button] once to switch the display in turn: 【Power Button】 Current speed SPEED, maximum speed MAX, and average speed AVG. Press the [Power Button] twice to switch the display in turn: voltage, single trip TRIP, and single trip time TRIP TIME Briefly press the ["+"...
Page 24
DISPLAY INTERFACE 1:Function Icon Introduction Menu Description Bluetooth - A flashing icon indicates no connection. Steady blue BLUETOOTH icon represents a successful connection to your phone. Long press and hold the ["+" button] to switch the light on, the LIGHTING light on the icon will light up, the light off, and the icon will not light up.
DISPLAY SPECIFICATION Model Display Specification u How to turn on/off the display: Use the included NFC key to turn the scooter on or off. u How to access the settings menu: Long press "+" and "-" buttons at the same time to enter the setting menu.
Conversely, upshifting while riding will suddenly increase the amount of power delivered via the throttle. YUME recommends that the throttle be released/disengaged when changing modes. Please use the mode switch function with caution.
NFC KEY BINDING Ø Step 1: Mobile App Installation u To install the Android app, search for [YUME RIDE] in the App Gallery or scan the QR code below to install the app. u For Apple IOS system, you can search for [YUME RIDE] in the APP Store or scan the QR code below to install the app.
Page 28
Bluetooth icon on the upper left corner of the [YUME RIDE] application home page to open the Bluetooth scooter identification settings page. u Click YUME SCOOTER to connect your scooter. When prompted enter the password(The default six-digit password is 000000) to successfully connect with your...
Page 29
NFC KEY BINDING Ø Step 3: “Add NFC” u Click “settings”. u Click to “Add NFC”. u Put the NFC key in the center of the display, and click the page to u The display wil “Search”. automatically search for NFC keys.
Page 30
NFC KEY BINDING Ø Step 3: “Add NFC” u Click "Bind Card" to u You may then change recognize your NFC the name of the NFC key and bind it to connection. your scooter. Ø Step 4: NFC lock/unlock your scooter u When the scooter is turned on and detects the NFC key near the vehicle sensing area, the scooter is automatically locked/unlocked without a password.
USAGE AND MAINTENANCE 1.Battery and charger The scooter is equipped with a dedicated Lithium battery and an intelligent charger. Please do not use another brand’s charge because it might not be suitable for the battery. The battery’s overall performance will change based on temperature, terrain, and weight of the user.
Page 32
USAGE AND MAINTENANCE 4. Brakes If you notice the braking performance deteriorating, check whether there is brake oil in the brake fluid reservoir or not. If there is none, do add it in order to get the brakes to the required sensitivity. If brake oil is added but the brake’s performance remains terrible, the brake pads might need urgent replacement.
GENERAL QUESTIONS SCOOTER CANNOT BE POWER ON Check whether the battery gets power or not. b. Open the foot pedal and check whether the issue is with the battery fuse. It might not be inserted properly or might have burnt out. Before closing the foot pedal, also check whether the main line between the electric scooter’s accelerator and controller is plugged in properly.
Page 34
How To Contact? • We have after-sales service, please contact the dealer where you purchased from. • View more detaile warranty terms on the YUME official website. Please Attention Limited Warranty Does Not Cover: • Scooter malfunctioning caused by prolonged usage.
Remember that you’d need a little while to adjust to using your new scooter. Watch the Terrain and Always: Be at Alert When riding your YUME scooter, carefully maneuver around water, speed bumps, sand, gravel, and anything that could cause your front wheel to stop.
Page 36
CONTACT US Technical support Team: support@yumeway.com If you have inquires please feel to contact us. We will reply within 8:30 am- 6:00 pm. Official Store Scan the code to discover the latest from YUME...
Need help?
Do you have a question about the YM-PREDATOR and is the answer not in the manual?
Questions and answers
Um I'm wondering what the magnaton setting is even for if you could explain that more for me because I have looked everywhere and haven't been able to find anything about it hahah thank you.