Related Manuals for YUME Y11+
Summary of Contents for YUME Y11+
- Page 1 YM Y11+ E-SCOOTER USER MANUAL Website: www.yumeway.com Mail: support@yumeway.com Facebook/Youtube: YUME Electric Scooter...
-
Page 2: Table Of Contents
CONTENTS Precautions for Riding .......... • Inspenction Before Riding......• Safety Precautions......... Product Description..........• Structure Parameter......... • Structure Diagram..........• Product Structure Size........• Product Packing List......... Product Assembly Operations....... • Pole Unfolding Operation......... • Install the Handlebar........• Install Command Centre........Product Use Operation......... -
Page 3: Precautions For Riding
WARNING! Ø Please conduct a thorough inspection of your scooter before riding. Always wear protective gear. Ø Abide by local laws, regulations, and speed limits. INSPECTION BEFORE RIDING Turn on the control panel. Make sure the brakes work properly and brake pads are not worn excessively. -
Page 4: Safety Precautions
SAFETY PRECAUTIONS A. Always wear a helmet,knee pads and elbow pads when riding. B. Use low speeds initially and gradually increase to higher speeds after as skills and confidence improve. C. Do not ride in the rain or through water puddles D. -
Page 5: Product Description
STRUCTURE PARAMETER PERFORMANCE Maximum Speed 50 Mph (80Km/h) Maximum Range 60 Miles (96km)* 3000W*2 dual motor with hall Motor Power sensor Speed Modes 3 Gears x 2 Drives Charging Time 6-7 hours Battery Capacity 60V 31.5Ah Water Resistance IP 54 for the whole scooter Wheel Size 11"... -
Page 6: Structure Diagram
STRUCTURE DIAGRAM... - Page 7 STRUCTURE SIZE...
-
Page 8: Product Packing List
CHECK AFTER UNPACKING When The Scooter After Unpacking: 1. Check if there are YUME bag & tools. 2. Check if there are 2 chargers. 3. Check if there are two NFC key. 4. Check if there is a display. 5. Seat installation (if available). -
Page 9: Product Assembly Operations
POLE UNFOLDING OPERATION Unfolding ① Press the silver snap ② Keep pressing the in the direction of the silver snap and push the arrow to completely lever in the direction of remove the snap from the arrow. the upper slot. ④... -
Page 10: Install The Handlebar
SCOOTER ASSEMBLY Handlebar Installation 1. Take out the handlebar, 2. Tighten the screws to align it with the pole and hold firmly in place. place it in a suitable position. 3. Take out the meter, 4. Finally, align the display loosen the two screws on to the center of the the meter, and remove it. -
Page 11: Install Command Centre
SCOOTER COMPONENTS SCOOTER ASSEMBLY Command Centre Installation ① Check that the LCD ② Make sure the light control panel and display switch,indicator light button screws are tight. switch/horn and display switch screws are tight. ③ Check that the left ④ Check that the thumb and right brake lever throttle screws are tight. -
Page 12: Product Use Operation
GET TO KNOW THE HANDLEBAR OF YOUR E-SCOOTER LCD Display Display Button Turning Signal Thumb Throttle Headlight Button Button/Horn... -
Page 13: Pole Folding Operation
POLE FOLDING OPERATION Folding Folding Mechanism. ① Release the locking bar and press the silver lever in the direction of the arrow to completely remove the latch from the slot. ② Lower the stem in the ③ When the silver latch direction of the arrow. -
Page 14: Display Function Operation
The password default password is: 1111(YUME RIDE application setting can change the password ). a. After turning the scooter on, place the NFC key near the display's NFC sensor to automatically unlock the scooter. -
Page 15: Display Button
DISPLAY BUTTON Button Name Function Press and hold the [power Button] for 3 seconds to switch on or off. Press the [Power Button] once to switch the 【Power Button】 display of MAX and AVG. Press the [Power Button] twice to switch the display units TRIP, TRIP TIME,Voltage. - Page 16 DISPLAY INTERFACE 1：Function Icon Introduction Menu Description Bluetooth - A flashing icon indicates no connection. Steady blue BLUETOOTH icon represents a successful connection to your phone. Battery meter - Battery levels are displayed in increments of 20%. BATTERY When battery level falls below 10%, the last red bar flashes. Current gear display - Press the "M"...
-
Page 17: Display Specification
DISPLAY SPECIFICATION Model Display Specification u How to turn on/off the display: Use the included NFC key to turn the scooter on or off. u How to access the P setting: Long press "M" and "F" buttons at the same time to enter the P setting menu. -
Page 18: Display P-Value Introduction
Conversely, upshifting while riding will suddenly increase the amount of power delivered via the throttle. YUME recommends that the throttle be released/disengaged when changing modes. Please use the mode switch function with caution. -
Page 19: Nfc Key Binding
NFC KEY BINDING Ø Step 1: Mobile App Installation u To install the Android app, search for [YUME RIDE] in the App Gallery or scan the QR code below to install the app. u For Apple IOS system, you can search for [YUME RIDE] in the APP Store or scan the QR code below to install the app. - Page 20 Bluetooth icon on the upper left corner of the [YUME RIDE] application home page to open the Bluetooth scooter identification settings page. u Click YUME SCOOTER to connect your scooter. When prompted enter the password(The default six-digit password is 000000) to successfully connect with your...
- Page 21 NFC KEY BINDING Ø Step 3: “Add NFC” u Click to “Add NFC”. u Click “settings”. u Put the NFC key in the center of the display, and click the page to u The display wil “Search”. automatically search for NFC keys.
- Page 22 NFC KEY BINDING Ø Step 3: “Add NFC” u Click "Bind Card" to u You may then change recognize your NFC the name of the NFC key and bind it to connection. your scooter. Ø Step 4: NFC lock/unlock your scooter u When the scooter is turned on and detects the NFC key near the vehicle sensing area, the scooter is automatically locked/unlocked without a password.
- Page 23 RECHARGING OPERATION Charging 1.First insert aviation head to the charging port 2.Insert in socket NOTE: Ensure that the three-pin connector is precisely aligned with the charging socket. Failure to do so may cause a short circuit within the charging port. Recharging Battery a.
-
Page 24: Usage And Maintenance General
USAGE AND MAINTENANCE 1.Battery and charger The scooter is equipped with a dedicated Lithium battery and an intelligent charger. Please do not use another brand’s charge because it might not be suitable for the battery. The battery’s overall performance will change based on temperature, terrain, and weight of the user. - Page 25 USAGE AND MAINTENANCE 4. Brakes If you notice the braking performance deteriorating, check whether there is brake oil in the brake fluid reservoir or not. If there is none, do add it in order to get the brakes to the required sensitivity. If brake oil is added but the brake’s performance remains terrible, the brake pads might need urgent replacement.
-
Page 26: General Questions
GENERAL QUESTIONS SCOOTER CANNOT BE POWER ON Check whether the battery gets power or not. b. Open the foot pedal and check whether the issue is with the battery fuse. It might not be inserted properly or might have burnt out. Before closing the foot pedal, also check whether the main line between the electric scooter’s accelerator and controller is plugged in properly. - Page 27 How To Contact？ • We have after-sales service, please contact the dealer where you purchased from. • View more detaile warranty terms on the YUME official website. Please Attention Limited Warranty Does Not Cover: • Scooter malfunctioning caused by prolonged usage.
-
Page 28: Safety Tips
Remember that you’d need a little while to adjust to using your new scooter. Watch the Terrain and Always: Be at Alert When riding your YUME scooter, carefully maneuver around water, speed bumps, sand, gravel, and anything that could cause your front wheel to stop. - Page 29 CONTACT US Technical support Team：support@yumeway.com If you have inquires please feel to contact us. Official Store Scan the code to discover the latest from YUME...