Related Manuals for Profoto Elevate
Summary of Contents for Profoto Elevate
- Page 1 User guide Profoto Elevate For other languages visit: Pour les autres langues, veuillez consulter: www.profoto.com...
- Page 2 www.profoto.com...
- Page 3 Profoto Elevate As you unpack the latest addition to your studio, you’ll quickly realize that Elevate is more than just a product. It’s a gateway to endless possibilities in visual content creation, a solution you can shape according to your needs to exhaust its full potential.
-
Page 4: General Safety Instructions
If the product enclosure should crack, immediately stop using the product, disconnect the mains cable from the wall outlet and contact Profoto Service. It is unavoidable that the type of capacitor used in flash products can sometime break. If this should happen a sharp smell may emit from the flash product along with smoke. Avoid getting the emission in the face. - Page 5 To clean the unit, wipe with a soft cloth moistened with a little mild detergent. Use another soft dry cloth to wipe dry. Profoto Elevate is an all-in-one photo studio machine intended for the professional creation of photos and videos of apparel, fashion, and accessories.
-
Page 6: Table Of Contents
Table of Contents General safety instructions ..................... 4 System overview ........................ 7 Technical specifications ....................8 Unpacking Elevate ......................10 Operation of the Elevate machine ................13 Safety considerations ................... 13 Normal operation ....................14 Installation ...........................17 Installation location ..................17 Electrical conditions ..................17 Safety PPE ......................17... -
Page 7: System Overview
System overview www.profoto.com... -
Page 8: Technical Specifications
Technical specifications Model name Elevate Regulatory model Profoto Elevate (70050010) Maximum ambient operating 10°C to +30°C/+50°F to +86°F temperature (Tma) Size Height: 198 cm (77.95 inch), including wheels Width: 70 cm (27.56 inch), excluding wheels, with wheels 79 cm (31.10 inch) Length: 92 cm (36.22 inch), including... - Page 9 No direct light entering the machine area Environment: System should not be installed in a sprinkler-controlled environment Maximum ambient operating 0°C–40°C temperature (Tma) Max power consumption: 10A (max) Line voltage: 100–230V AC Operating Frequency 50/60 Hz For more technical specifications, go to profoto.com. www.profoto.com...
-
Page 10: Unpacking Elevate
Unpacking Elevate To unbox and set up Profoto Elevate you will need two people with lifting strength and a Philips head screwdriver (a battery powered screwdriver can be used). Start by carefully lifting the box into the upright position as shown below. The opening side is marked and is made up of two parts, the top cover and the bottom ramp element. - Page 11 Once the ramp is lowered and stable, start by releasing the front accessible wheel brakes. Next remove the plastic covering and using both people, carefully roll the unit down the ramp onto the floor and lock the brakes in place. Remove the protective foam retainers. www.profoto.com...
- Page 12 You are now ready to power up and calibrate the system using the included power cable and ethernet network cable. Unlock the wheels, move into position and power up. Now you can use the Operation guide above, or for the full manual, visit Profoto.com/support. www.profoto.com...
-
Page 13: Operation Of The Elevate Machine
Elevate Designed and manufactured in The Netherlands. Profoto B.V. Siriusdreef 32/68, 2132 WT Hoofddorp, The Netherlands. Profoto Ltd, Lytchett House, 13 Freeland Park, Wareham Road, Poole, Dorset, BH16 6FA, UK, www.profoto.com... -
Page 14: Normal Operation
Maintenance of the machine that requires opening of the housing should only be carried out by Profoto personnel, or under direct supervision by a Profoto trained support partner. To avoid the risk of electrical shock, the main switch must be turned off and the power cord disconnected from the inlet before performing maintenance and opening the machine. - Page 15 5. In the normal operation, the Profoto App on the iPad controls all functions of the machine. An operation manual can be found at: https:/ /support.profoto.com/support An example of the user interface is shown below. www.profoto.com...
- Page 16 7. If a hard reset of the machine is required, when instructed to by Profoto Support power off the camera pole using the power switch at the base, (pictured above). A restart will initiate a calibration sequence first.
-
Page 17: Installation
All electrical outlets and lighting should conform to local electrical safety requirements before installation commences. Power outlets to be used by the Elevate machine must conform to the technical characteristics outlined above in section 2. There is to be no ongoing electrical works taking place in the installation area during the installation of Profoto Elevate. -
Page 18: Risk Assessment
Installation works are not normally hazardous by nature, however the training in work procedures, safe systems of working and management systems that Profoto employ ensure that the works are completed in a safe manner. The following risks have been identified as potential hazards when installing Profoto Elevate: •... -
Page 19: Product End Of Life
Deinstallation should only be done following the same guidelines for installation and should only be performed by or under the guidance of trained Profoto technical staff. All risk, safety and PPE guidelines are the same as installation. -
Page 20: Annual Onsite Inspection
Annual onsite inspection • Clean inside and outside of the Elevate metal components, so there is no dust on vital components. • Check metal components for damage and repaint any small scratches using the provided paint. • Use a spirit level to make sure the camera pole is level. - Page 21 • Take pictures of the room and report anything that can be of any help for support. • Bring all photos back to the office or email them to support. www.profoto.com...
-
Page 22: Declaration Of Conformity
Declaration of Conformity EU Declaration of Conformity Hereby, Profoto Aktiebolag declares that the Profoto Elevate is in compliance with Directive 2014/53/ EU. The full text of the EU declaration of conformity can be found at https:/ /profoto.com/int/support/declaration-of-conformity Manufacturer: Profoto B.V. - Page 23 2. this device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications made to this equipment not expressly approved by Profoto may void the FCC authorization to operate this equipment. www.profoto.com...
- Page 24 • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. www.profoto.com...
- Page 25 www.profoto.com...
- Page 26 www.profoto.com...
- Page 27 www.profoto.com...
- Page 28 Profoto AB Box 1264, 172 25 Sundbyberg Sweden +46 (0) 8 447 53 00 info@profoto.com www.profoto.com...
Need help?
Do you have a question about the Elevate and is the answer not in the manual?
Questions and answers