Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Holzstar BTS 151
Summary of Contents for Holzstar BTS 151
- Page 1 Operating Instructions Belt and disc grinding machine BTS 151 BTS 151...
-
Page 2: Table Of Contents
15 Spare parts ...........19 itly permitted. Contraventions are liable to compensa- 15.1 Ordering spare parts........19 tion. 16 Spare parts drawing......20 17 Electrical wiring diagram.....21 Subject to technical modifications and error. 18 EC-Declaration of Conformity.....22 BTS 151 | Version 1.05... -
Page 3: Introduction
All information and notes in these operating instructions You have made a good choice by purchasing the Belt were summarised taking the applicable standards and and disc grinding machine made by HOLZSTAR. rules, the state-of-the-art and our long-term knowledge and experiences into consideration. -
Page 4: Obligations Of The Operating Company
- The operator must have all safety devices checked bears the legal product responsibility for the protection of the user, the staff or for third parties. regularly for their good working order and their in- tegrity. BTS 151 | Version 1.05... -
Page 5: Qualification Of Personnel
Certain works may only be performed by specialist per- sonnel of the manufacturer. Other personnel is not au- thorized to perform these works. Please contact our cus- tomer service for the execution of all arising work. BTS 151 | Version 1.05... -
Page 6: Safety Signs On The Machine
Please wear ear protection when working with the - Never change the electrical system. device. - Do not expose power tools to wet or damp conditi- ons. Water that enters a power tool increases the risk of electric shock. BTS 151 | Version 1.05... -
Page 7: Intended Use
The improper use of the belt and disc grinding machine as well as the disregard of the safety regulations or the operating instructions exclude a liability of the manu- facturer for resulting damage to persons or objects and cause the warranty to lapse! BTS 151 | Version 1.05... -
Page 8: Technical Data
The removal of danger spots, disturbances and unevenness at the time of trans- port by other employees leads to considerable dangers. Fig. 2: Type plate BTS 151 Careful planning of internal transport is therefore essen- tial. -
Page 9: Packaging
- Grinding belt 915x100mm K 80 13. Belt alignment Item number: 5911008 14. Bracket - Grinding belt 915x100mm K 100 15. Mounting holes Item number: 5911010 - Grinding belt 915x100mm K 120 Item number: 5911012 BTS 151 | Version 1.05... -
Page 10: Assembly
2 screws (Fig. 6). The edge of the table must be positioned so that there is a maximum di- stance of 2 mm to avoid pinching workpieces or fingers between the table and the grinding wheel. BTS 151 | Version 1.05... -
Page 11: Settings
Now carefully pull off the old sanding belt (11). Tighten the new sanding belt (11) and align it. Finally tighten the sanding belt (11) over the tensioning lever (10) and tigh- ten the screws of the grinding wheel (22). BTS 151 | Version 1.05... -
Page 12: Aligning The Abrasive Belt Holder
Remove the screw to remove the belt and disc grinding check the barrel. Change the run again if necessary. machine drive cover. Loosen the three fixing screws (Fig. 11.2) to be able to align the abrasive belt holder. Fig. 12: Adjustment the belt BTS 151 | Version 1.05... -
Page 13: Vertical Grinding
ON / OFF Switch To turn on the machine, press the green switch with the sign (|) for about one second. To switch off the machine, press the switch with the symbol (O), as shown in Fig. 15. BTS 151 | Version 1.05... -
Page 14: Surface Grinding On The Sanding Belt
Hold the workpiece firmly with both hands and apply light pressure to the sanding belt. Move the workpiece back and forth slightly. Hold the workpiece firmly with both hands and proceed as shown in Fig.19. BTS 151 | Version 1.05... -
Page 15: Grinding Ends On The Grinding Wheel
The edge of the worktable must be positioned so that there is a maximum distance of 2 mm to the grinding wheel to avoid pinching workpieces or fingers bet- ween the table and the grinding wheel. Fig. 20: Grinding ends BTS 151 | Version 1.05... -
Page 16: Care, Maintenance And Repair16
The belt and disc sanding machine is delivered ready to and mount the work table and the cover. use. Before each use, a functional test should be perfor- med. The sanding belt must be tensioned. BTS 151 | Version 1.05... -
Page 17: Maintenance
Wood burns during grinding Grinding wheel or belt is covered with Replace the sanding belt or the grinding lubricant. There is too much pressure wheel. Reduce the pressure on the work- on the workpiece piece. BTS 151 | Version 1.05... -
Page 18: Disposal Instructions/Recycling Facilities
14.3 Disposal of electrical appliances NOTE! Please wear in your and for the sake of Ensure that all components of the machine are dispo- sed of in the designated and approved BTS 151 | Version 1.05... -
Page 19: Spare Parts
- Only use original spare parts of the manufacturer or spare parts admitted by the manufacturer. - Type of device: BTS 151 - Always contact the manufacturer in case of uncer- - Item number: 5903151 tainties. -
Page 20: Spare Parts Drawing
The following drawing is intended to help in case of service, to identify necessary spare parts. To order send a copy of the parts drawing with marked components to your dealer. Fig. 22: Spare parts drawing BTS 151 BTS 151 | Version 1.05... -
Page 21: Electrical Wiring Diagram
Electrical wiring diagram 17 Electrical wiring diagram Fig. 23: Wiring diagram BTS 151 BTS 151 | Version 1.05... -
Page 22: Ec-Declaration Of Conformity
<= 16 A per phase and not subject to conditional connection Kilian Stürmer, Stürmer Maschinen GmbH, Responsible for documentation: Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 25.01.2019 ______________________ Kilian Stürmer Managing Director BTS 151 | Version 1.05... - Page 23 Notes 19 Notes BTS 151 | Version 1.05...
- Page 24 www.holzstar.de...
Need help?
Do you have a question about the BTS 151 and is the answer not in the manual?
Questions and answers