Related Manuals for Holzstar BTS Series
Summary of Contents for Holzstar BTS Series
- Page 1 Operating Instructions Belt and disk grinder BTS series BTS 150 | BTS 250 Status 23 Nov 2011 | Version 1.02...
- Page 2 BTS 250 Manufacturer Stürmer Maschinen GmbH Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt Telephone: 0049 (0) 951 96555 - 0 Fax: 0049 (0) 951 96555 - 55 E-mail: info@holzstar.de Internet: www.holzstar.de Information on Operating Instructions Original operating instructions Issue: 07/02/2012 Version: 2.01 Language:...
- Page 3 Dear customer, Thank you for buying a HOLZSTAR® product. HOLZSTAR® machines offer a high quality, optimum technical solution and are excellent value for money. Constant further development and product innovations are always a guarantee of the latest technological knowledge and safety. It is our great concern that you enjoy this product which will make your job easier and bring added value to your business.
-
Page 4: Table Of Contents
Table of contents Page Machine designation Designated use Technical data Noise level ..............................6 Safety information Residual risks............................7 Unpacking and installation Scope of delivery and accessories Scope of delivery ............................8 Special accessories ............................8 Control elements Assembly Safety stop ...............................10 Work table ..............................10 Settings Pivoting the work table ..........................11 Centring the work desk ..........................11... -
Page 5: Machine Designation
1. Machine designation A nameplate is fitted onto the machine which identifies the machine, article number and important technical data. Always keep the nameplate clean and in legible condition. 2. Designated use The belt grinder and disk grinder of said type is designed only for grinding wood or wood-like materials. -
Page 6: Noise Level
Noise level This machine emits noise (sound pressure level) which can exceed 82 dB(A) in the workplace. For this reason the operator should take noise and hearing protection measures. Note: It must be noted that the duration of exposure to noise, the type and nature of the work area and other machines in simultaneous operation can affect the noise level in the workplace. -
Page 7: Residual Risks
Wear tight working clothes, safety goggles and protective shoes and use hearing protection. Tie up long hair. Do not wear watches, wristbands, chains, rings or gloves (rotating parts!). Repair immediately any defect which can compromise safety. Never step on the machine. Heavy injuries can occur should the machine tilt over. ... -
Page 8: Scope Of Delivery And Accessories
Standard grinding belt and grinding disk Operator’s tools Set of screws Special accessories We recommend using only high-quality original Holzstar accessories. Faultless operation and optimal work results can be guaranteed only with original accessories. Identification article number Grinding belt Korn 60 (pack of 10) -
Page 9: Control Elements
7. Control elements 1 Track adjustment screw 9 Safety stop 2 Grinding belt bedding 10 Grinding belt 3 Clamping lever 11 Attachment bore 4 Work table holding bore 12 ON / OFF switch 5 Attachment bore 13 Grinding disk guard 6 Grinding unit adjustment screw 14 Work table 7 Clamping screw table pivoting... -
Page 10: Assembly
8. Assembly Safety stop Take the safety stop as shown in the figure and attach it by using the hexagon screw M6 x 1.0-14 and toothed washer. When tightening the screw, ensure that the safety stop is attached approx. 3 mm above the grinding belt. Do not tighten the screw entirely, otherwise you may strip the thread. -
Page 11: Settings
9. Settings Note: Before taking any action on the machine, the power supply must be disconnected. Only persons familiar with the handling and functionality of the machine may handle and work with the machine. Pivoting the work table Loosen the clamping screw and place the work desk in the desired position. -
Page 12: Replacing Grinding Disks
Replacing grinding disks Disassemble the work desk. Loosen both grinding unit guard screws and remove them. Replace the grinding disk with a new one and fix the guard again. Replacing grinding belts Reduce tension of the grinding belt by using the clamping lever. Now carefully pull the old grinding belt off. -
Page 13: Machine Control
10. Machine control 10.1 General Follow the instructions below to ensure that the results of your work are successful as expected. ATTENTION! Rotating parts! Work carefully and use common sense. Pay attention to what you are doing. Especially beware of the rotating parts. Wear tight clothes. Make sure that your hair or clothes are not caught by rotating parts! Wear a hair net. -
Page 14: Surface Grinding On The Grinding Belt
10.3 Surface grinding on the grinding belt Check if the safety stop is correctly mounted and properly tightened. Carefully push the work piece as shown in the figure with both hands against the grinding belt and safety stop. For better material collection, the work piece can easily be moved back and forth. -
Page 15: Grinding Round Pieces On The Grinding Disk
10.6 Grinding round pieces on the grinding disk Hold the work piece firmly with both hands and proceed as shown in the figure above. Attention: Grind round pieces only on the left side, on the side running downwards, otherwise the work pieces may be thrown off. 10.7 Grinding ends on the grinding disk If you need to grind the ends of a narrow work piece,... -
Page 16: Cleaning, Maintenance And Repairs
12. Cleaning, maintenance and repairs Prior to commencement of any cleaning, maintenance and/or repair work, always disconnect the machine from the power supply! Note: Oil, grease and cleaning agents are harmful to the environment and must not be disposed of in waste water or standard refuse. -
Page 17: V-Belt Replacement
12.4 V-belt replacement Prior to commencement of any cleaning, maintenance and/or repair work, always disconnect the machine from the power supply! Remove the belt casing guard by loosening the cross-head screw. Loosen the three fixing screws which hold the belt tight. Put the new belt in place and clamp it by placing a slotted screwdriver into the bore and pushing the belt casing upwards. -
Page 18: Ec Declaration Of Conformity
EC declaration of conformity Pursuant to machinery directive 2006/42/EC appendix II 1.A Manufacturer/distributor Stürmer Maschinen GmbH Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt Product group: Metallkraft Metal processing machines ® Machine identification: BTS 150 / BTS 250 Machine type: Belt and disk grinder Article number: 5904150 / 5904250 Serial number:... -
Page 19: Spare Parts Orders
16. Spare parts orders Spare parts can be ordered via vendors or directly from the manufacturer. The following key data must be reported when requesting or ordering a spare part: - device type - article number - position number - year of manufacture - amount - required mode of shipment (post, freight, sea, air, express) - shipping address... -
Page 20: Explosion Drawing Bts 150
17. Explosion drawing BTS 150... -
Page 21: Explosion Drawing Bts 250
18. Explosion drawing BTS 250... - Page 22 Stürmer Maschinen GmbH | Dr.-Robert-Pfleger-Str. 26 | D-96103 Hallstadt Telephone: 0049 (0) 951 96555-0 | Fax: 0049 (0) 951 96555-55 | E-mail: info@holzstar.de | Internet: www.holzstar.de The content of these Operating Instructions is under the exclusive ownership of Stürmer Maschinen GmbH. Distribution and copying of this document, and any usage and communication of its content are prohibited unless expressly permitted.
Need help?
Do you have a question about the BTS Series and is the answer not in the manual?
Questions and answers
Puis-je avoir la référence de la courroie de la machine BTS 250 pour que je puisse la commander,merci
The belt references for the Holzstar BTS 250 machine are:
- Grinding belt Korn 60 (pack of 10): 5911006
- Grinding belt Korn 80 (pack of 10): 5911008
- Grinding belt Korn 100 (pack of 10): 5911010
- Grinding belt Korn 120 (pack of 10): 5911012
- Grinding belt Korn 150 (pack of 10): 5911015
This answer is automatically generated