Advertisement

Available languages

Available languages

DJ DUAL VOCAL
USER MANUAL
INSTRUKCJA OBSŁUGI

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DJ DUAL VOCAL and is the answer not in the manual?

Questions and answers

Summary of Contents for DNA Professional DJ DUAL VOCAL

  • Page 1 DJ DUAL VOCAL USER MANUAL INSTRUKCJA OBSŁUGI...
  • Page 2 ENGLISH UHF DSP Wireless Microphone System Specification Modulation Method: ∏/4 – DQPSK Frequency Range: 518-542MHz, 2x1 CH Sampling Ratio: 48KHz Transmission Rate: 204.8Kbps Dynamic Range >90dB Total Harmonic Distortion: <0.1% Delay Time of Audio Transmission: <3ms S/N Ratio: >96dB Frequency Response: 30~20KHz RX Sensitivity: <-94dBm Unique ID Address: Yes Some tips to improve the performance of the system...
  • Page 3: Hand-Held Transmitter

    of the receiver is lighted. The receiver’s output voice volume can be controlled by adjusting the volume knob. Attention when you install the receiver It should be 1m high from the floor It should be more than 1m beyond the wall Antennas should be put out fully, otherwise it’ll influence receiving signals 1.
  • Page 4 3. Receiver Function 1) Front panel functions 2) Rear panel functions...
  • Page 5: Bodypack Transmitter Functions

    Bodypack transmitter functions  Elements 1) Antenna 2) Signal socket 3) Frequency display 4) Power indicator 5) LCD display 6) IR port 7) Battery tray 8) Battery cover 9) Microphone head  Replacing the battery...
  • Page 6: Troubleshooting

    4. Troubleshooting Trouble Status Solutions Turn on the transmitter power. Confirm that the +/- marks on The transmitter’s display is the battery match with the head joint of the transmitter. set off Insert a new battery. Confirm whether a head of the AC power adapter is plugged into the power outlet, and whether the other end is inserted Receiver’s display is set off into the DC power supply socket on the rear panel of the re-...
  • Page 7 POLSKI Specyfikacja techniczna Modulacja: ∏/4 – DQPSK Zakres częstotliwości: 518-542MHz, 2x1CH Współczynnik próbkowania: 48KHz Prędkość przesyłu danych: 204.8Kbps Zakres dynamiki: >90dB Całkowite zniekształcenia harmoniczne: <0.1% Opóźnienie transmisji audio: <3ms Stosunek dźwięku do szumów: >96dB Pasmo przenoszenia: 30~20KHz Czułość RX: <-94dBm Wskazówki pomagające w uzyskaniu najlepszego efektu ...
  • Page 8 Ostrzeżenia przy montowaniu odbiornika Powinien znajdować się minimum 1m nad ziemią Powinien znajdować się minimum 1m od ściany Anteny powinny być wyciągnięte w całości, inaczej może to wpływać na odbierany sygnał 1. Nadajnik doręczny 1) Główne funkcje 1 Główka mikrofonu 3 Przełącznik zasilania 2 Okno wyświetlacza 4 Obudowa baterii...
  • Page 9 2) Wymiana baterii Dwie baterie powinny wystarczyć na 8 godzin pracy. W mo- mencie gdy wskaźnik baterii pokazuje oznacza to, że należy wymienić baterię. Aby tego dokonać należy postępo- wać jak na rysunku po lewej stronie. 2. Funkcje odbiornika 1) Funkcje przedniego panelu 1 Przełącznik zasilania 2 Okno wyświetlacza 3 Regulacja głośności...
  • Page 10 3. Funkcje nadajnika przypaskowego  Budowa 1) Antena 2) Gniazdo sygnału 3) Wyświetlacz częstotliwości 4) Wskaźnik zasilania 5) Wyświetlacz LCD 6) Port IR 7) Miejsce na baterie 8) Pokrywa baterii 9) Główka mikrofonowa  Wymiana baterii...
  • Page 11: Rozwiązywanie Problemów

    4. Rozwiązywanie problemów Problem Status Rozwiązanie Wyświetlacz nadajnika jest Włącz nadajnik. Upewnij się, że znaczniki baterii +/- pasują do wyłączony gniazda baterii. Wymień baterię na nową. Wyświetlacz odbiornika jest Upewnij się, że zasilacz jest podłączony do prądu oraz do wyłączony gniazda z tyłu odbiornika.

Table of Contents