Related Manuals for RIDGID RP 350
Summary of Contents for RIDGID RP 350
- Page 1 RP 350/RP 351 anual RP 350/RP 351 Press Tools GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 2: Table Of Contents
RP 350/RP 351 Press Tools Table of Contents Recording Form For Machine Serial Number ......................1 Safety Symbols/Symbols..............................2 General Power Tool Safety Warnings Work Area Safety................................2 Electrical Safety ................................2 Personal Safety ................................3 Power Tool Use And Care ............................3 Battery Tool Use And Care ............................3 Service ..................................4... -
Page 3: Safety Symbols/Symbols
RP 350/RP 351 Press Tools Safety Symbols/Symbols In this operator’s manual and on the product, safety symbols and signal words are used to communicate important safe- ty information. This section is provided to improve understanding of these signal words and symbols. -
Page 4: Personal Safety
RP 350/RP 351 Press Tools trolled with the switch is dangerous and must be • If operating a power tool in a damp location is repaired. unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces •... -
Page 5: Service
The tool includes a second operating mode (“Control can break or throw parts and cause injury. Stand Mode”) that can be turned on using the RIDGID Link App. clear during use and wear appropriate protective equip- Control Mode allows the fitting to be engaged prior to ment, including eye protection. - Page 6 2 Attachment Mounting Pin 8 Handle 3 Tool Status Lights 9 Battery 4 ON/OFF Button Figure 1 – RIDGID RP 350 Press Tool and Standard 10 Run Switch Series Jaw 5 Warning Label 11 LED Work Light (RP 351 Underside)
- Page 7 Releasing the switch will not stop the tool once it has locked on. This assures consistent, repeatable press connection integrity. Mode can be changed with RIDGID Link App, see Bluetooth Functions section. Pressure Allows tool to be released without completing press. If used, press connection is not complete Release Button and must be repeated.
-
Page 8: Specifications
Duty Cycle ....3 Press /min. 3 Press /min Power Supply ....RIDGID RB-18XX Series 18 V Li-Ion Battery Pack or RIDGID RPA 120/220 AC Power Adapter (See Optional Equipment Section) Bluetooth Range ..33 ft. (10 m) 33 ft. (10 m) Permissible Humidity ..80% maximum... -
Page 9: Set-Up And Operaton
2. Inspect the work to be done and determine the cor- between the fully open and fully closed position. rect RIDGID tool and RIDGID attachment for the Pin should lock into each position. Confirm that the application per their specifications. Using incorrect run switch moves freely and does not bind or stick. -
Page 10: Pressing A Fitting With Typical Scissor Jaws
RP 350/RP 351 Press Tools 2. With dry hands, insert a fully charged battery or AC Adapter into tool. If using the corded power adapter with a GFCI, the GFCI (RCD) should have a rated residual current of 30 mA or less. Depress ON/OFF button one time to turn tool ON. -
Page 11: Pressing A Fitting With Typical Actuator And Press Ring Set
Transfer) Normal Mode: Depress the run switch (Figures 1 & 2). The RIDGID ® RP 350 and RP 351 Press Tools include Once the tool cycle begins and the rollers contact the Bluetooth ® wireless technology allowing wireless data... -
Page 12: Cold Weather Operation
Press tools should be less than 33 ft. operate. (10 m) from the device to be detected. Any Service and repair on the RP 350 and RP 351 Press Tools obstacle between the tool and device can must be performed by a RIDGID Independent Press Tool reduce the operational range. -
Page 13: Troubleshooting
To reduce the risk of serious injury, only use equip- 64383 RBC-30 Charger North America ment specifically designed and recommended for 56523 RBC-30 Charger Europe use with the RP 350 and RP 351 Press Tools, such 64388 RBC-30 Charger China as listed below. 64393 RBC-30 Charger Australia... -
Page 14: Disposal
RP 350/RP 351 Press Tools Electromagnetic Compatibility Disposal (EMC) Parts of these tools contain valuable materials and can be recycled. There are companies that specialize in recycling The term electromagnetic compatibility is taken to mean that may be found locally. Dispose of the components in the capability of the product to function smoothly in an compliance with all applicable regulations. -
Page 15: Ec Declaration Of Conformity
EC DECLARATION RIDGID ® RP 350/RP 351 Press Tools EC DECLARATION OF CONFORMITY 2006/42/EC, 2014/30/EU, 2011/65/EU IEC 62841-1, EN 61000-6-1, EN 61000-6-3 Complies with UL 62841-1 csa c22.2 No. 62841-1 E114309 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... - Page 16 © 2020 RIDGID, Inc. Printed 9/20 The Emerson logo and RIDGID logo are registered trademarks of Emerson Electric Co. or RIDGID, Inc. in the U.S. and other countries. 999-995-220.10 EC44835/11 All other trademarks belong to their respective holders.
Need help?
Do you have a question about the RP 350 and is the answer not in the manual?
Questions and answers