Table of Contents
Advertisement
LAN
(10/100)
COAXIAL
ASSIGNABL
OUT
IN
1
IN
2
DC OUTPUT
for WIRELESS LAN
(OUTPUT 5 V
0.6 A MAX)
(
DVD
)
(
CD
)
Internet
ADAPTER PORT
(OUTPUT 5 V
0.1 A MAX)
TENNA
UNBAL
Modem
AM LOOP
RIUS
A
FRONT
CENTER
SURROUND
R
L
R
IN
SUBWOOFER
CAUTION:
ATTENTION:
Router
PRE OUT
SPEAKER IMPEDANCE
ENCEINTE D'IMPEDANCE DE
SPEA
6 -16 .
6 -16 .
WAN
DC 5V
Ethernet
WPS
Wireless LAN converter (AS-WL300)
Connecting an IR receiver
If you keep your stereo components in a closed
cabinet or shelving unit, or you wish to use the
sub zone remote control in another zone, you
can use an optional IR receiver (such as a Niles
or Xantech unit) to control your system instead
of the remote sensor on the front panel of this
receiver.
! Remote operation may not be possible if direct
light from a strong fluorescent lamp is shining
on the IR receiver remote sensor window.
! Note that other manufacturers may not use
the IR terminology. Refer to the manual that
came with your component to check for IR
compatibility.
! If using two remote controls (at the same
time), the IR receiver's remote sensor takes
priority over the remote sensor on the front
panel.
1 Connect the IR receiver sensor to the IR
IN jack on the rear of this receiver.
Closet or shelving unit
Pioneer
Non-Pioneer
component
component
CONTROL
IR
IN
IN
OUT
HDMI
IN
VIDEO IN
BD IN
DVD IN
DVR/BDR IN
OUT
LAN
1
DC OUTPUT
ASSIGNABLE
1
for WIRELESS LAN
(OUTPUT 5 V
0.6 A MAX)
CONTROL
VIDEO
AUDIO
ZONE 2
DVR/BDR CD-R/TAPE ZONE 2
IN
ADAPTER PORT
OUT
L
TV/SAT
VIDEO
(OUTPUT 5 V
OUT
IN
IN
OUT
OUT
0.1 A MAX)
MONITOR
IR
OUT
IN
R
ANTENNA
FM UNBAL
OUT
DVR/
CD
BDR
75
L
AM LOOP
12 V
1
SIRIUS
A
FRONT
C
TRIGGER
OUT
IN
DVD IN
IN
IN
R
L
IN
1
R
(OUTPUT
2
(DVD)
12 V
ASSIGN
IN
ABLE
TOTAL
IN
2
L
150 mA
(DVR/
MAX)
BDR)
IN
IN
R
SUBWOOFER
MONITOR
OUT
Y
P
P
TV/SAT VIDEO
DVD
B
R
CAUTION:
ATTENTION
RS-232C
COMPONENT VIDEO
PRE OUT
SPEAKER IMPEDANCE
ENCEINTE D'IMPE
6 -16 .
6 -16 .
IR receiver
2 Connect the IR IN jack of another
component to the IR OUT jack on the rear
of this receiver to link it to the IR receiver.
Please see the manual supplied with your IR
receiver for the type of cable necessary for the
connection.
! If you want to link a Pioneer component to
the IR receiver, see Operating other Pioneer
components with this unit's sensor on page
23 to connect to the CONTROL jacks instead
of the IR OUT jack.
Operating other Pioneer
components with this unit's
sensor
Many Pioneer components have SR CONTROL
jacks which can be used to link components
together so that you can use just the remote
sensor of one component. When you use a
remote control, the control signal is passed
along the chain to the appropriate component.
! If you want to control all your components
using this receiver's remote control, see page
53.
! If you have connected a remote control to the
CONTROL IN jack (using a mini-plug cable),
you won't be able to control this unit using the
remote sensor.
Important
! Note that if you use this feature, make sure
that you also have at least one set of analog
audio, video or HDMI jacks connected to
another component for grounding purposes.
1 Decide which component you want to
use the remote sensor of.
When you want to control any component in the
chain, this is the remote sensor at which you'll
point the corresponding remote control.
2 Connect the CONTROL OUT jack of that
component to the CONTROL IN jack of
another Pioneer component.
Use a cable with a mono mini-plug on each end
for the connection.
HDMI
IN
1
VIDEO IN
BD IN
DVD IN
DVR/BD
ASSIGNABLE
1
VIDEO
AUDIO
CONTROL
ZONE 2
DVR/BDR CD-R/TAPE ZONE 2
IN
OUT
L
TV/SAT
VIDEO
OUT
IN
IN
OUT
OUT
MONITOR
IR
OUT
IN
R
DVR/
OUT
CD
BDR
L
12 V
1
TRIGGER
IN
IN
OUT
IN
DVD IN
IN
1
2
R
(OUTPUT
(DVD)
12 V
ASSIGN
ABLE
TOTAL
IN
2
L
150 mA
(DVR/
MAX)
BDR)
IN
IN
R
MONITOR
OUT
Y
P
P
TV/SAT VIDEO
DVD
B
R
RS-232C
COMPONENT VIDEO
IN
OUT
IN
OUT
CONTROL
CONTROL
Connecting your equipment
3 Continue the chain in the same way for
as many components as you have.
Switching components on and
off using the 12 volt trigger
You can connect components in your system
(such as a screen or projector) to this receiver
so that they switch on or off using 12 volt
triggers when you select an input function.
However, you must specify which input func-
tions switch on the trigger using the The Input
Setup menu on page 26 . Note that this will only
work with components that have a standby
mode.
HDMI
IN
1
VIDEO IN
BD IN
DVD IN
DVR/BDR IN
ASSIGNABLE
1
CONTROL
VIDEO
AUDIO
ZONE 2
DVR/BDR CD-R/TAPE ZONE 2
IN
OUT
TV/SAT
VIDEO
OUT
IN
IN
OUT
OUT
MONITOR
OUT
IR
IN
DVR/
CD
OUT
BDR
12 V
1
TRIGGER
OUT
IN
DVD IN
IN
IN
IN
1
(OUTPUT
2
(DVD)
12 V
ASSIGN
ABLE
TOTAL
IN
2
150 mA
(DVR/
MAX)
BDR)
IN
IN
MONITOR
OUT
Y
P
P
TV/SAT VIDEO
DVD
B
R
RS-232C
COMPONENT VIDEO
12 V TRIGGER
INPUT
% Connect the 12 V TRIGGER jack of this
receiver to the 12 V trigger of another
component.
Use a cable with a mono mini-plug on each end
for the connection.
After you've specified the input functions that
will switch on the trigger, you'll be able to
switch the component on or off just by pressing
the input function(s) you've set on page 26.
03
L
(O
0
R
ANT
FM UN
75
L
SIRIU
R
L
R
SU
PR
23
En
- Quick Links:
- Rear Panel
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
