Asus E510MA Series Disassembly Procedure
  1. Manuals
  2. Brands
  3. Asus Manuals
  4. Laptop
  5. E510MA Series
  6. Disassembly procedure
Asus E510MA Series Disassembly Procedure

Asus E510MA Series Disassembly Procedure

Hide thumbs

Advertisement

Table of Contents

Disassembly Procedure
Please follow the information provided in this section to perform the complete disassembly procedure of
the Notebook. Be sure to use proper tools described before.
A
SUS E510MA Series notebook consists of various modules. This chapter describes the
procedure for the complete notebook disassembly and assembly (Assemble document
please look up from the last page). In addition, in between procedures, the detailed
disassembly procedure of individual modules will be provided for your service needs.
The disassembly procedure consists of the following steps:
Disassembly Procedure
1
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E510MA Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Asus E510MA Series

Summary of Contents for Asus E510MA Series

  • Page 1 Please follow the information provided in this section to perform the complete disassembly procedure of the Notebook. Be sure to use proper tools described before. SUS E510MA Series notebook consists of various modules. This chapter describes the procedure for the complete notebook disassembly and assembly (Assemble document please look up from the last page).
  • Page 2 Disassembly Procedure...

  • Page 3: Service Overview

    Disassembly Procedure Service Overview Pre-repair checklist Precautions Before you perform any service or repair on the notebook, please follow the steps below first. 1. Be sure that the notebook is powered down. 2. Before disassembling any part, please disconnect all power source. ex: AC plug/Battery connector/Power protect screw etc.
  • Page 4 Disassembly Procedure 4. Always wear a ground strap on your hand to protect the notebook from static discharge. 5. Please refer to “ANSI ESD S20.20” about ESD protection measure. 6. Put disassemble the parts in the functional PE BAG for avoid any damages of the A/B/C/D part.
  • Page 5 Disassembly Procedure 9. Screw Appearance Criteria. If the screws have the following damaged appearance, please do not use. a. Shape deformed. b. Paint scratched off. c. Rusty. d. Damaged head – unable to drive in. e. Damaged unable to securely tighten. 10.
  • Page 6 Disassembly Procedure Appropriate Tools The illustrations below show the appropriate tools that should be used for the notebook’s service and repair. ➢ Cross Screwdriver Please accord to different screw specification to choose different screwdriver and head. Below photos are for reference only. Use a cross screwdriver to fasten/remove screws.
  • Page 7 Disassembly Procedure ➢ Thickness gauge Thickness compass specification 0.05mm-1.5mm. Use it to measure the gap.
  • Page 8 Disassembly Procedure Bottom Case Module The illustrations below show how to remove the Bottom Case Module. Notice: After disassembling bottom case, if you want to replace any part, please be sure to disconnect the battery connector more than ten seconds to avoid damaging any part. 1.
  • Page 9 Disassembly Procedure Snaps as below For Plastic and Metal...
  • Page 10 Disassembly Procedure Parts: ⚫ Total screw * 10 ⚫ BOTTOM CASE *1 ⚫ (Actual part name depends on different SKU.)

  • Page 11: Battery Module

    Disassembly Procedure Battery Module The illustrations below show how to remove the Battery Module. Disconnect the battery connector. Follow below numbers to remove 4 screws on the battery module. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2.0KG±0.2kgf . 3.
  • Page 12 Disassembly Procedure Disconnect the battery cable. Parts: ⚫ Total screw * 4 ⚫ Battery SMP/LP485780/3S1P/11.55V/42WH *1 ⚫ (Actual part name depends on different SKU.)
  • Page 13 Disassembly Procedure IO Board The illustrations below show how to remove the IO Board. Disconnect the IO FFC remove 5 screws. Assembly Notice: follow the reverse numbers to lock screws. Screw tightening torque: 2.5KG±0.2kgf Screw tightening torque: 2.0KG±0.2kgf Rotate the hinge and take out the IO Board. Disconnect the IO FFC.
  • Page 14 Disassembly Procedure Assembly notice: Please change new one, If FFC is damage during disassembly. Here are some samples of FFC damage: Parts: ⚫ Total screw * 5 ⚫ IO FFC 16P 0.5MM,L204.5//GOO DONG/G12459-A*1 ⚫ IO_BD.//R2.0*1 ⚫ (Actual part name depends on different SKU.)

  • Page 15: Wlan Module

    Disassembly Procedure WLAN Module The illustrations below show how to remove the WLAN Module. Remove the antenna connectors. Remove 1 screw and take out the WLAN. Screw tightening torque: 2.0KG±0.2kgf M2*2.5L Take out the AUX Antenna. Please arrange the antenna well when you assemble it.
  • Page 16 Disassembly Procedure Parts: ⚫ Total screw * 1 ⚫ 802.11AC+BT5.0(2*2)M.2_WW//IN/9560.NGWG.NV957715JFP2/BLK *1 ⚫ (Actual part name depends on different SKU.)

  • Page 17: Ssd Module

    Disassembly Procedure SSD Module The illustrations below show how to remove the SSD Module. 1. Remove 1 screw on Motherboard and take the SSD away. Assembly Notice: follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2.0KG±0.2kg SSD ABSORBER (optional) THM SSD PAD//LAIRD (optional) M2*2.5L...

  • Page 18: Speaker Module

    Disassembly Procedure Speaker Module The illustrations below show how to remove the Speaker Module. 1. Disconnect the TP FFC FP FFC. Assembly notice: Insert FFC to the bottom until just accord with the line when lock the latch. 2. Tear up the TP GASKET CABLE ACETONE TYPE.
  • Page 19 Disassembly Procedure 3. Disconnect the speaker cable and take out the speaker. Please arrange the speaker cable well when you assemble it. Assembly notice: Please change new one, If FFC is damage during disassembly. Here are some samples of FFC damage:...
  • Page 20 Disassembly Procedure Parts: ⚫ Total screw * 0 ⚫ SPEAKER MODULE * 1 ⚫ TP FFC 8P 0.5MM,L103.5//XINYA/X20AA1-9880-HP*1 ⚫ FP FFC 8P 0.5MM,L131.5//XINYA/X19AA1-8632-HP*1 ⚫ TP GASKET *1 ⚫ CABLE ACETONE TYPE*1 ⚫ (Actual part name depends on different SKU.)

  • Page 21: Touchpad Module

    Disassembly Procedure Touchpad Module The illustrations below show how to remove the Touchpad Module. Remove 3 screws and take out the touchpad. Assembly Notice: follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 1.6KG±0.2kgf. SCREW M2*1.5L Parts: ⚫...

  • Page 22: Thermal Module

    Disassembly Procedure Thermal Module The illustrations below show how to remove the Thermal Module. Remove 6 screws. Assembly Notice: follow the reverse numbers to lock screws. Screw tightening torque: 2.0KG±0.2kgf Screw tightening torque: 2.0KG±0.2kgf Screw tightening torque: 2.0KG±0.2kgf 2. Take out the Thermal Module. SCREW M2*4L M2*2.5L SCREW M2*3L...
  • Page 23 Disassembly Procedure ⚫ Assembly Notice: After replacing a new MB, please clean remaining CPU GREASE on thermal module and then paste new U20A CPU PAD. Parts: ⚫ Total screw * 6 ⚫ THERMAL MODULE// *1 ⚫ (Actual part name depends on different SKU.)
  • Page 24 Disassembly Procedure Motherboard Module The illustrations below show how to remove the Motherboard Module. 1. Disconnect EDP Cable Keyboard Cable. Assembly Notice: Please well arrange the cables. 2. Remove 4 screws on the hinge and rotate it. Assembly Notice: follow the reverse numbers to lock screws. Screw tightening torque: 2.5KG±0.2kgf Take out the mainboard.
  • Page 25 Disassembly Procedure SCREW M2.5*5L Parts: ⚫ Total screw * 4 ⚫ MAIN_BD. *1 ⚫ (Actual part name depends on different SKU.)
  • Page 26 Disassembly Procedure Top Case Module The illustrations below show how to remove the Top Case Module. Follow the direction of the arrows to rotate the hinges, take out the Top Case . Parts: ⚫ Total screw * 0 ⚫ K/B_(ND)_MODULE*1 ⚫...
  • Page 27 Disassembly Procedure LCD Module for Plastic SKU The illustrations below show how to remove the LCD Module. 1. Remove 2 screw mylars. 2. Remove 2 screws on the Bezel. Screw tightening torque: 2.5KG±0.2kgf SCREW M2.5*3.5L 3. Use plastic blade to pry up the edge , take the LCD front bezel out .
  • Page 28 Disassembly Procedure Assembly Notice: Because of the LCD Bracket issue, there is a question which is “Large Gap Between LCD Cover and Bezel” after you assemble the LCD Bezel. Please follow below steps to assemble LCD Bezel: Press the stress points of red arrows on the bezel edge to assemble the bezel.
  • Page 29 Disassembly Procedure to confirm the “Gap Between LCD Cover and Bezel”. If the gap is Rotate the LCD Panel large, please repeat the step 1 to narrow the gap. If you find the hook of Bezel damage, please change new one. 4.
  • Page 30 Disassembly Procedure SCREW M2.5*3L Notice: If you need to replace hinges, please make sure hinge R and hinge L are the same vendor. Disconnect and arrange the EDP Cable MAIN Antenna. Please arrange the cable well when you assemble them.
  • Page 31 Disassembly Procedure 6. Remove 2 screws on the bracket. Assembly Notice: follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2.0KG±0.2kgf. SCREW M2*2.5L 7. Pry out the LCD Bracket and rotate the LCD carefully. 8. Disconnect the EDP Cable and take out the LCD Bracket carefully.
  • Page 32 Disassembly Procedure ⚫ Assembly Notice: Insert the left LCD Bracket into the left LCD Cover slot by pressuring, then lock the screw(M2*2.5). hook hook hook Insert the right LCD Bracket into the right LCD Cover slot by pressuring, then lock the screw. hook hook hook...
  • Page 33 Disassembly Procedure Connect the EDP Cable. Rotate the LCD Panel and insert it into LCD Bracket carefully.
  • Page 34 Disassembly Procedure 9. Tear up the foil and take out the Antenna Cable . Assembly Notice: Please well arrange the cable and put it in the hook slot as below. 10. Disconnect the EDP Cable and remove it.
  • Page 35 Disassembly Procedure Assembly Notice: Please well arrange the EDP Cable and put it in the hook slot as below. 11. Take out the camera. Snaps as below For Plastic SKU...
  • Page 36 Disassembly Procedure Parts: ⚫ Total screw * 10 ⚫ LCD BEZEL SCREW MYLAR *2 ⚫ LCD BEZEL SUB ASSY *1 ⚫ HINGE L*1 ⚫ HINGE R*1 ⚫ LCD BRACKET R ASM//TYT KS*1 ⚫ LCD BRACKET L ASM//TYT KS *1 ⚫ LCD COVER SUB ASSY *1 ⚫...
  • Page 37 Disassembly Procedure LCD Module for Metal SKU The illustrations below show how to remove the LCD Module. 1. Remove 2 screw mylars. 2. Remove 2 screws on the Bezel. Screw tightening torque: 2.5KG±0.2kgf SCREW M2.5*3.5L 3. Use plastic blade to pry up the edge , take the LCD front bezel out .
  • Page 38 Disassembly Procedure Assembly Notice: Because of the LCD Bracket issue, there is a question which is “Large Gap Between LCD Cover and Bezel” after you assemble the LCD Bezel. Please follow below steps to assemble LCD Bezel: Press the stress points of red arrows on the bezel edge to assemble the bezel.
  • Page 39 Disassembly Procedure to confirm the “Gap Between LCD Cover and Bezel”. If the gap is Rotate the LCD Panel large, please repeat the step 1 to narrow the gap. If you find the hook of Bezel damage, please change new one. Notice: 1.
  • Page 40 Disassembly Procedure X513FP LCD BEZEL ADHESIVE UP ◆ Use the thinner plastic blade to pry up the edge . The plastic blade thickness : Please refer to the Gap Step of LCD Bezel to Panel on the last page. Tips : Usually, it is hard to pry up the inside edge follow below position directly.
  • Page 41 Disassembly Procedure 4. Follow below numbers to remove 6 screws and take out the hinges . Assembly Notice: follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2.5KG±0.2kgf. SCREW M2.5*3L Notice: If you need to replace hinges, please make sure hinge R and hinge L are the same vendor .
  • Page 42 Disassembly Procedure 6. Pull out the easy-pull glue (adhesive) in left and right side gently, take out the panel.
  • Page 43 Disassembly Procedure Notice : Please slowly pull the adhesive up about 30 degree. 30゜ The position of the adhesive as below : please stick new ones when you assemble it.
  • Page 44 Disassembly Procedure 7. Disconnect the EDP Cable and take out the LCD Bracket carefully.
  • Page 45 Disassembly Procedure Tear up the foil and take out the Antenna Cable . Assembly Notice: Please well arrange the cable and put it in the hook slot as below. 12. Disconnect the EDP Cable and remove it.
  • Page 46 Disassembly Procedure Assembly Notice: Please well arrange the EDP Cable and put it in the hook slot as below. 13. Take out the camera. Snap as below: For Metal SKU...
  • Page 47 Disassembly Procedure Parts: ⚫ Total screw * 8 ⚫ LCD BEZEL SCREW MYLAR *2 ⚫ LCD BEZEL SUB ASSY *1 ⚫ HINGE L*1 ⚫ HINGE R*1 ⚫ LCD COVER SUB ASSY *1 ⚫ WIFI MAIN ANTENNA*1 ⚫ LCD panel *1 ⚫...

Table of Contents