PayFacto PAX A920 Installation Manual
Multi-terminal charging base
Hide thumbs
Also See for PAX A920:
- Configuration and setup (15 pages) ,
- Installation manual (8 pages) ,
- Quick reference manual (2 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PayFacto PAX A920
Summary of Contents for PayFacto PAX A920
- Page 1 December, 2022...
-
Page 2: Table Of Contents
Contents Introduction............................... 3 Charging Base Overview .......................... 5 Requirement............................5 Overview.............................. 5 Base Components..........................6 Charging Base Installation ........................7 Installing the Multi-Terminal Charging Base ..................7 Installing Terminal Silicone Sleeves....................9 Using the Charging Base ........................11 Powering the Charging Base On or Off ..................... 11 Charging Terminals.......................... -
Page 3: Introduction
Multi-Terminal Installation Guide Charging Base This document explains how to install the multi-terminal charging base for PAX A920 or A920 Pro terminals and included silicone sleeves. NOTE: The multi-terminal charging bases are designed to be used with only one model of PAX terminal, either the A920 or A920 Pro. - Page 4 PAX A920/A920 Pro Multi-Terminal Installation Guide Charging Base Copyright © 2022 PayFacto Inc. Page 4 of 13...
-
Page 5: Charging Base Overview
To ensure the best charging results, you must use the original AC power adapter that came with your PAX A920 or A920 Pro terminals. The AC power adapter should have the PAX logo printed on one side as shown below: Your multi-terminal charging base comes with the following:... -
Page 6: Base Components
PAX A920/A920 Pro Multi-Terminal Installation Guide Charging Base The following images show the location of the main charging base components: AC power cord Multi-terminal charging bases (x5) USB charging cables (x5) Six (6) outlet power bar Anti-slip rubber pads Copyright © 2022 PayFacto Inc. -
Page 7: Charging Base Installation
PAX A920/A920 Pro Multi-Terminal Installation Guide Charging Base Before you install and connect the multi-terminal charging base, make sure that the desired location is within reach of an AC outlet and that there is enough space to for the charging base and the terminals when connected. - Page 8 PAX A920/A920 Pro Multi-Terminal Installation Guide Charging Base Working one cable at a time, connect the cable’s USB plug into the AC adapter’s USB port. Plug the adapter into an outlet on the power bar. Repeat steps 4 and 5 for each additional charging cable. After you connect all 5 cables to the power bar, plug in the power bar's cable to an available AC outlet.
-
Page 9: Installing Terminal Silicone Sleeves
DO NOT connect any additional devices to the charging base's power bar. To protect your PAX A920 or A920 Pro terminals from minor impact damage, you should install the silicone sleeves provided with the multi-terminal charging base as the charging bases are designed specifically for terminals with the sleeve. - Page 10 PAX A920/A920 Pro Multi-Terminal Installation Guide Charging Base Insert the top of the terminal into the sleeve's printer protection until the sleeve fits snugly onto the terminal’s top. Pull the bottom of the sleeve over the bottom edge of the terminal. Repeat for every terminal you intend to place on the charging bases. NOTE: To add or change a SIM card, you need to remove the sleeve from the terminal.
-
Page 11: Using The Charging Base
PAX A920/A920 Pro Multi-Terminal Installation Guide Charging Base The multi-terminal charging base has a power switch on the attached power bar, shown below: • To power on the terminal charging base, make sure the power cord is plugged into a grounded AC outlet and that the power switch is in the On/RESETposition;... -
Page 12: Led Status Light
PAX A920/A920 Pro Multi-Terminal Installation Guide Charging Base NOTE: The charging base should only be used to charge your terminal(s); it is not designed to be a storage location for the terminal(s). If the status light remains blue after you place the terminal on the base, the terminal is not seated correctly, and not connecting to the base’s gold charging contacts. - Page 13 PAX A920/A920 Pro Multi-Terminal Installation Guide Charging Base Blue: Charging base is plugged in, no terminal connected. Red/Yellow: Terminal is charging. Green: Terminal is fully charged. Copyright © 2022 PayFacto Inc. Page 13 of 13...
Need help?
Do you have a question about the PAX A920 and is the answer not in the manual?
Questions and answers