Subscribe to Our Youtube Channel
Related Manuals for unicraft HSWH Series
Summary of Contents for unicraft HSWH Series
- Page 1 Operating Instructions Hydraulic Bottle Jack HSWH 3 HSWH 30 HSWH 50 HSWH 30 HSWH 3...
-
Page 2: Table Of Contents
4 Technical Data ............7 4.1 Table..............7 4.2 Type plate............7 Fax: 0049 (0) 951 96555 - 55 5 Transport, packaging, storage.......7 Email: info@unicraft.de 5.1 Transport ............7 URL: www.unicraft.de 5.2 Packaging............7 5.3 Storage ............... 7 6 Description of device ..........8 7 Bevore the first use..........8... -
Page 3: Introduction
Introduction Introduction 1.3 Limitation of liability All information and notes in these operating instructions You have made a good choice by purchasing the UNI- were summarised while taking applicable standards CRAFT hydraulic bottle jack. and rules, the state-of-the-art technology and our long- term knowledge and experiences into consideration. -
Page 4: Obligations Of The Operating Company
Safety - The operating company must be informed about the applying industrial safety regulations and fur- CAUTION! ther analyse hazards resulting from the special This combination of symbol and signal words indica- working conditions at the place of use of the hy- tes a possibly dangerous situation which may lead draulic bottle jack. -
Page 5: Personal Protective Equipment
Safety Only persons reliable working procedures can be ex- 2.5 General safety regulations pected from, are allowed to perform all works. Persons the responsiveness of which is affected by e. g. drugs, alcohol or medication, are not allowed to work with the NOTE! machine. -
Page 6: Safety Instructions For The Operating Personnel
Intended use Intended use 2.6 Safety instructions for the operating personnel The hydraulic bottle jack is used exclusively for vertical lifting of vehicles up to the specified maximum load. It is Any operation that impairs the safety of the machine not intended for horizontal use!! must be avoided. -
Page 7: Technical Data
Technical Data Technical Data 4.2 Type plate 4.1 Table Model HSWH 3 HSWH 30 HSWH 50 Load-carrying capacity Min. height (A) 194 mm 188 mm 207 mm Stroke (B) 118 mm 118 mm 127 mm Adjustment height (C) 60 mm 60 mm 70 mm Lift height (D) -
Page 8: Description Of Device
Description of device Description of device Operation Illustrations in this manual may differ from the original. ATTENTION! - Avoid overload. Check that the load never exceeds the value indicated on the type plate - Never use a rusted or damaged hydraulic bottle jack. -
Page 9: Workflow
Operation 8.3 Workflow 8.3.2 Lower the vehicle Step 1: Open the drain valve by inserting the narrow end of the pump lever into the valve and slowly tur- 8.3.1 Lifting the vehicle ning the pump lever to the left. Step 1: Close the open drain valve (Pos. 2, Fig. 5) by tur- ning the narrow end of the pump lever to the Step 2: When the vehicle is completely lowered, pull the right (Pos. -
Page 10: Venting
Care, maintenance and repair Care, maintenance and repair 8.3.5 Venting After some time, air bubbles can penetrate the jack‘s hy- 9.1 Care by cleaning draulic system and impair its function. The hydraulic bottle jack should always be kept in a Venting the hydraulic cylinder is carried out as follows: clean condition. -
Page 11: Oil Changes
Disposal, recycling of used devices 10 Disposal, recycling of used devices 9.3 Oil changes In order to ensure that the hydraulic bottle jack functions Please take care in your own interest and in the interest of properly, change the oil regularly. the environment that all component parts of the machine Step 1: Retract the pistons completely. -
Page 12: Troubleshooting
Troubleshooting 11 Troubleshooting Fault / Possible cause Drain valve is not properly closed. Insufficient oil. Top up the hydraulic oil. Too much oil. Drain oil from the filling opening. Air in the cylinder. Open the drain valve and pump several times. Close the drain valve. -
Page 13: Spare Parts
Spare parts 12 Spare parts Example The pump lever for the hydraulic bottle jack HSWH 30 must be ordered. The pump lever has in the spare parts DANGER! drawing the number 23. Risk of injury due to use of incorrect spare parts! When ordering spare parts, send a copy of the spare The use of incorrect or faulty replacement parts may... -
Page 14: Spare Parts Drawing Hswh 30 And Hswh
Spare parts 12.2 Spare parts drawing HSWH 30 and HSWH 50 Fig. 7: Spare parts drawing HSWH 30 and HSWH 50 Pos. Description Qty. Pos. Description Qty. Round wire snap ring Spring Rectangular ring Spring holder O-Ring Ball bearing Ø 3 mm Stamp assembly Ball bearing Ø... -
Page 15: Eu Declaration Of Conformity
13 EU Declaration of Conformity According to machine directive 2006/42/EC Annex II 1.A Stürmer Maschinen GmbH Manufacturer/distributing company: Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt hereby declares that the following product Unicraft® Workshop technology Product group: Hydraulic Bottle Jack Type of machine: Designation*: Item number: HSWH 3... - Page 16 www.unicraft.de...
Need help?
Do you have a question about the HSWH Series and is the answer not in the manual?
Questions and answers