Cool Mode; Fan Mode - GE AJHS10DCC Owner's Manual & Installation Instructions

ge.com
COOLMODE
Remote C ontrol
l. Px_ss COOLpad.
2. Px_ss LOW. IVIED or HIpads to set desired fire speed.
3. PI_SS the
INCREASEA/DECREASEV
pads to set the
desix_d tempenmu'e 60°F to 85°F in l °F increments.
Control P anel
l. Pxess fl_e MODEpad until tile COOLindicator lig]lt is
lit and the LOW. MEDor Hlin(ficator light is lit fi)r
die (lesix_(1thn speed.
2. Pxess the INCREASEA/DECREASET pads to set the
desix_d temperature 60°F to 85°F in l °F increments.
A them/ostat is used to maint_fin tile room
temperature. Tile compressor will e_cle on and off
to kee I) tile room at tile set level of (omfi)rt. Set tile
thermostat at a lower number and file indoor _firwill
become coolex; Set tile thermostat at a higher nmnber
and tile indoor air will become _mnex:
NOTE: ff theair conditioner i s off andis thenturnedon
whileset toCOOL, it willtakeapproximately 3minutesfor
thecompressor tostartandcoolingtobegin.
CoolingDescriptions
ForNormalCooling--Select tile COOL mode and
HIGHor MEDthn with a middle set temperature.
ForMaximum Cooling--Select tile COOLmode
and HIGHtim with a lower set temperatm>.
ForQuieter & Nighttime C ooling--Select tile COOL mode
and LOWthn widl a middle set temperature.
NOTE: If youswitchfroma COOL s ettingtoOFF or to
a fansetting,wait atleast3 minutes beforeswitchingback
toa COOL s etting.
Fan Switch
Tile thn switch is located behind tile ti'ont grille on the
control box. Access through a hole in control box.
_,_]mn set at
CYCLE (do_n)
tile thn e',cles on and ottl
When set at
CONT (continuous, up)
tile tim runs
all
tile
time providing a m(/x_ balanced mml)eraU/x_. The unit
is shipped in the
CONrsetting.
FAN MODE
Use tile FAN mode to provide _dr circulation and
filtering without cooling. Since fhn only settings (1(1 not
provkle cooling, a temperature setting will not be
displa}ed.
Remote Control
Px>ss FANpad. Press LOW. IVIED or HI pads to set
(lesix_(1 fhn speed.
Control Panel
Pxess die MODEpad until tile FANindicator light is lit
and tile LOW, IVIED or HIin(ficator light is lit fi)r the
(lesix_(1 fan speed.
Vent Control
The vent control is located behind tile ti'ont grille on
tile right side of tile air (fischarge area. "_\lmn set at
CLOSE, o nly the air inside fl_e room will be circulated
and conditioned. When set at OPEN, some inside air is
exhausted outside.
To opeIl or
close
tile vent:
1. Remove the ti'ont grille.
2. Remo\ e the vent card scx_.
3. Remove vent card, turn it over and replace it 17}
locating rear hole in card over locating pin inside air
discharge and reattaching scre_ at fi'ont.
Theunit leavesthe factoryset at theCLOSE position.
._Locating hole
Screw hole "_.
OPEN position
(Meshendtowardback)
Screwho
CLOSE position
(Meshendtowardfront)
A# Direction
Horizontal lomers
on fl_e Ii'ont grille let
you control tile air
(lirection up and
doPvI/.
Remove tile fi'ont
grille to a@/st the
vertical lou\'ers
side-to_ide to
dixect file air
left or fight.