Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Embention R12F
Summary of Contents for Embention R12F
- Page 1 R12F Hardware Manual Release 1.0 Embention 2024-02-23...
-
Page 3: Table Of Contents
4.1.1 R12F OEM Assembly ........ - Page 5 R12F Hardware Manual, Release 1.0 Veronte R12F is a DC-DC converter with input voltage supply variable. Warning: Select your version before reading any user manual. The following image shows where to select a version from any Embention user manual. CONTENTS...
- Page 6 R12F Hardware Manual, Release 1.0 CONTENTS...
-
Page 7: Introduction
CHAPTER INTRODUCTION Fig. 1: Veronte R12F Veronte R12F is a DC-DC converter, with an input power supply variable from 14 to 160 V and 12 V of output voltage. - Page 8 R12F Hardware Manual, Release 1.0 Chapter 1. Introduction...
-
Page 9: Quick Start
CHAPTER QUICK START This user manual covers the of Veronte R12F. To use it, weld input and output wires according mechanical assembly to the section, then fix it to the assembly frame. Pinout Fig. 1: Input and output diagram 2.1 Warnings •... - Page 10 R12F Hardware Manual, Release 1.0 Chapter 2. Quick Start...
-
Page 11: Technical
CHAPTER THREE TECHNICAL 3.1 Variants Veronte R12F is offered in two versions: R12F and R12F OEM. Name Reference Description R12F P003960 Protected by an enclosure made of diecast aluminum, with watertight enclosure. R12F OEM P008605 Smaller, lighter and with better heat dissipation, but mechanical protection may be required. - Page 12 R12F Hardware Manual, Release 1.0 Fig. 2: R12F dimensions (mm) Fig. 3: R12F OEM dimensions (mm) Fig. 4: R12F OEM mounting holes position (mm) Chapter 3. Technical...
-
Page 13: Hardware Installation
CHAPTER FOUR HARDWARE INSTALLATION 4.1 Mechanical 4.1.1 R12F OEM Assembly M4 screws are recommended for mounting. In saline environments such as coastal and oceanic, the screw material must be stainless steel. To weld the cables read the section of this manual Pinout 4.1.2 R12F Assembly... -
Page 14: Vibration Isolation
There might be situations where external isolation components might be needed. Veronte R12F can be mounted in different ways in order to reject the airframe vibration. The simplest way could be achieved by just using double-sided tape on the bottom side. Other ways may use some external structure which could be rigidly attached to the airframe and softly attached to R12F (e.g. -
Page 15: Pinout
R12F Hardware Manual, Release 1.0 4.3 Pinout The following diagram shows the holes to weld each cable. • HV IN: Positive of the input power supply (from 14 to 160 V DC). • HV GND: Ground of the input power supply. - Page 16 R12F Hardware Manual, Release 1.0 Chapter 4. Hardware Installation...
-
Page 17: Maintenance
CHAPTER FIVE MAINTENANCE Apart from cleaning, no extra maintenance is required to guarantee the correct operation of Veronte R12F. In order to clean Veronte R12F properly follow the next recommendations. • Turn off the device before cleaning. • Use a clean, soft, damp cloth to clean the unit. - Page 18 R12F Hardware Manual, Release 1.0 Chapter 5. Maintenance...
-
Page 19: Acronyms And Definitions
CHAPTER ACRONYMS AND DEFINITIONS Direct Current DC-DC Direct Current to Direct Current Ground Original Equipment Manufacturer... - Page 20 R12F Hardware Manual, Release 1.0 Chapter 6. Acronyms and Definitions...
-
Page 21: Contact Data
CHAPTER SEVEN CONTACT DATA You can contact Embention if you need further help and support. Embention contact data is as follows: Email: support@embention.com Telephone: (+34) 965 421 115 Address: Polígono Industrial Las Atalayas, C/ Chelín, Nº 16, CP 03114, Alicante (España).
Need help?
Do you have a question about the R12F and is the answer not in the manual?
Questions and answers