Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any too(s listed
here.
Took Needed
[]
Flat=blade and Phillips
[]
Tape measure
screwdrivers
[]
Drilland %2" orsmallerbit
[]
Level
Through=the=Wall
Installation:
In addition to the tools listed above, the following tools are
needed for through4he-waU
installation.
[]
Saw
[]
1" (2.Scm) orthicker
lumber
[]
Wood preservative
[]
Caulk
[]
#10 x l" wood screws (7)
IMPORTANT:
Observe all governing codes and ordinances.
Check the location where air conditioner will be installed. Proper
installation is your responsibility,
Make sure you have everything
necessary (or correct installation.
The location should provide:
[]
Grounded electrical outlet within 4 ft (I 22 cm) of where the
power cord exits the air conditioner.
NOTE: Do not use an extension cord.
[]
Free movement of air in room to be cooled.
[]
A large enough opening for the air conditioner,
[]
Adequate wallsupportforweightof
air conditioner. Air
conditioner
weighs between 70 and 851bs (32 to 40 kg),
NOTE: Cabinet louvers must not be obstructed.
Air must be able
to pass freely through the cabinet louvers.
Parts Supplied (on some models)
Check that all parts are included in parts package.
C
B
E
F
H
G
A. Foam window sash seal
B. Window lock bracket
C. Side curtains (2)
D. Foam seal
D
E. #10x 7/2" pan-head
Phillipsscrews
(3)
F. #10x _" round-head screws (6)
G. Top channel
H. #10x
¼" pan-head Phillips screws (3)
A. Cabinet
louvers
NOTE: Installation parts are supplied (or double-hung
windows
up to 36" (91.4 cm) wide. A special Wide Window Kitis available
from your dealer or service center. See "Accessories."
NOTE: DO NOT USE ANY SCREWS OTHER THAN
THOSE SPECIFIED HERE
PiN 2020213A0016
1
Advertisement
Related Manuals for Frigidaire FAZ12ES2A
Summary of Contents for Frigidaire FAZ12ES2A
- Page 1 (or correct installation. Took Needed The location should provide: Flat=blade and Phillips Tape measure Grounded electrical outlet within 4 ft (I 22 cm) of where the screwdrivers power cord exits the air conditioner. Drilland %2" orsmallerbit Level NOTE: Do not use an extension cord.
-
Page 2: Window Installation
The wall opening measurements should be: Width: 22s/8"(57.5 cm) plus twice thickness of wood used to build frame. Height: 16" (40.6 cm) plus twice thickness of wood used to bui{d frame. Depth: 2_/2 " (6.4 cm) minimum to 6V2" (16.5cm) maximum. -
Page 3: Installation Instructions
Pull on the handles to slide the air conditioner out of the air conditioner, cabinet. Place the air conditioner on cardboard. Failure to do so can result in back or other injury. Remove packaging materials Remove and dispose of/recycle packaging... - Page 4 1. Locate provided bag of screws. 2. Place the top channel on top of the air conditioner cabinet, lining up the 3 holes in the top channel with the 3 holes on top A. Curtain housing of the air conditioner cabinet.
- Page 5 Front View The place where the power cord exits the air conditioner should be no more than 4 it (1 22 cm) from a grounded 3 prong outlet. Do not block the louvers on the front panel.
- Page 6 3. Use a 3/32" d rill bitto drill starter holes through the holes in the bracket into the window sash. 4. Attach the window lock-bracket to the window sash with 2-#10 x 3/4_' r ound-head screws to secure window in place.
- Page 7 Plug into a grounded 3 prong outlet. Press RESET on the power supply cord. 2. Insert front tabs of front panel into top of cabinet and swing front into place...