nashi Yaiza Pro Instruction Manual

Toilet intelligent

Advertisement

Yaiza Pro
intelligent
Toilet
Instruction Manual
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Yaiza Pro and is the answer not in the manual?

Questions and answers

Summary of Contents for nashi Yaiza Pro

  • Page 1 Yaiza Pro intelligent Toilet Instruction Manual...
  • Page 2 Catalogue Technical specifications------------------------------ Detailed product information----------------- Manual-------------------------------- Daily maintenance------------------------------------ Remote control manual-----------------------...
  • Page 3: Technical Specifications

    Technical specifications 220VAC/50HZ 110VAC/60HZ Voltage 1030W Power 1270W Power Main module Minimum water pressure required 0.07 MPa (20L/min flow), maximum water pressure 0.8 Water pressure range MPa (hydrostatic pressure) 1.5m approx. Power cord Volume of water Tank capacity 200mL Heating power 1250W Hot water temperature Level 1-4...
  • Page 4: Detailed Product Information

    Detailed product information ① Screw (1 pc.) control unit ② Support (1 pc.) distance ③ ③ Remote control (1 pc.) ② ① ④ ④ Expansion screw (1 pc.) Manual Manual Manual ① inlet hose ③ (white) ② three way connector ③...
  • Page 5 Yaiza Pro Power indicator cable feeding Button light sensor Disassembly button Foot switch Dryer seat cover spray lance Nozzle Seat Night light Anal washing motherboard Ceramics Washed perineal/feminine...
  • Page 6 Yaiza Pro Power indicator cable feeding Button night light sensor Disassembly button Foot switch Dryer seat cover Nozzle spray lance Seat Night light Anal washing motherboard Washed perineal/feminine...
  • Page 7 Manual Connect the inlet hose to the angle valve Board Mounting plate Attach the gasket to the drain, insert the mounting piece into the clay and tighten until to be placed in the right place. Apply glass glue around of the plate, direct the toilet towards it and place it in its corresponding place.
  • Page 8 Manual Water supply and electrical preparation 2.Connect the plug to the power outlet, press the power button reboot. If the indicator light comes on, it means that there is current 1..Open the inlet angle valve and check that the screw threaded (press the leakage current test button;...
  • Page 9 Module control panel operation 1. Short press the power button to switch between e work and power saving mode. 2.Long press the power button for 3 seconds to put the main motor into standby mode. Short press the power to return to work mode. 3.
  • Page 10: Daily Maintenance

    Daily maintenance Module maintenance 1.Turn off the power. 2.Clean dirty parts with a dry cloth. 3.Connect it after cleaning. Nozzle maintenance 1.When the seat is not in use, press the "anal wash" button on the module control panel or the "child wash/self- cleaning"...
  • Page 11 Cleaning the mesh filter 1 Unplug, close the inlet valve, remove the inlet pipe. . Remove the mesh filter and use a brush to clean it. 2 Reassemble the mesh filter, connect the inlet pipe and open the inlet valve. Remove the mesh filter.
  • Page 12: Remote Control Manual

    Remote control manual...
  • Page 13 Catalogue 1.Installation preparation 01.Remote control installation 2.Instruction manual 01.Remote control description 02.Anal washing//Perineal/female washing 03.Children's wash/Nozzle cleaning. 04. Dryer 05.Massage 06.Nozzle position adjustment 07.Water pressure adjustment 08.Unloading the cistern 09.Light/Energy Saving 10.Temperature adjustment 11.Key combination...
  • Page 14 Installation Preparation Installing the remote control Installing the remote control holder (1) Use a drill to drill a 6mm diameter and 35mm deep hole (hole location: make sure for users to reach the remote control while using the toilet seat). (2) Tear off the paper of the double-sided adhesive tape.
  • Page 15 Instructions Anal washing//Perineal/female washing When you occupy the seat and press the "Anal Wash//Perineal Wash/Female" button, the washing function will be activated for one cycle and switch to the drying function automatically. If you press the "stop" button in the middle of the cycle, the anal wash/perineal wash/ feminine wash function will stop and the drying function will not start.
  • Page 16 Instructions Massage Press the "Anal Wash/Massage" button or the "Perineal Wash/Female//Motion" button, and then press it a second time to start the moving massage function. The nozzle moves back and forth to expand the range of the washing function. Press the button again to turn off the massage function. Nozzle position adjustment Press the button "▲"either "▼"to adjust the position of the nozzle to one of the 5 available levels while using the "Anal Wash", "Perineal/Female Wash"...
  • Page 17 Instructions Night light / Energy saving Night light By pressing the "Light/Energy Saving" button, it switches the mode between smart off/on modes; The mode changes each time this button is pressed. When you start smart mode, the night light flashes three times and automatically turns on or off based on the surrounding conditions. Energy saving Energy Saving Mode: Turns off the seat heating and water heating functions indefinitely.
  • Page 18 Instructions Temperature adjustment Seat temperature adjustment: Press the "Seat temperature" button and adjust the seat temperature. He The light indicator will show the level from 1 to 3 in blue. Adjusting water temperature: Press the "Water Temperature" button and adjust the water temperature. He The light indicator will show the level from 1 to 3 in red.

Table of Contents