Advertisement
Time Flow Recess Adaptor
Installation and Maintenance Instructions
TFC794R
technical data
Working Pressure Range
Recommended Pressure
Maximum Static Pressure
Maximum Working Temperature
Inlet Connection
Operating Force
Flow Time
Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA) and AS/NZS3500.
Installations not complying with PCA and AS/NZS 3500 may void the product and performance warranty provisions.
Reference should also be made to the Australasian Health Facility Guidelines (AHFG), ABCB and Local Government
regulations when considering the choice of, and the installation of these products.
This product must be installed and commissioned by a qualified plumber.
For use with potable water only.
NOTE: Enware Australia advises:
1. Due to ongoing Research and Development, specifications may change without notice.
2. Component specifications may change on some export models.
I00258_22 Jan 2024
1300 369 273 | info@enware.com.au | enware.com.au
Min 50 kPa Max 500 kPa
250 - 300 kPa
1000 kPa (For testing purposes / system commissioning)
70°C
5/8" BSP (standard tap body)
47N @300 kPa
15 seconds
* Flow times are indicative only and may vary depending on water supply
pressure and flow conditions.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Watts ENWARE TFC794R
Summary of Contents for Watts ENWARE TFC794R
- Page 1 Time Flow Recess Adaptor Installation and Maintenance Instructions TFC794R technical data Working Pressure Range Min 50 kPa Max 500 kPa Recommended Pressure 250 - 300 kPa Maximum Static Pressure 1000 kPa (For testing purposes / system commissioning) Maximum Working Temperature 70°C 5/8”...
- Page 2 Locking ring Grub screw - M5X6 S/S 304 Time flow cartridge Body O-ring 17x12x2.5 Fibre washer 28.5x23x1.5MM Spanner www.enware.com.au Page 2 © Enware Pty Ltd...
-
Page 3: Installation
installation WALL/ • All supply lines must be flushed thoroughly to remove debris TILE SURFACE prior to the installation of this product, as per AS/NZS 3500.1. Strainers (40 mesh) are recommended if debris is an ongoing problem. • A thermostatic mixing valve and a pressure reduction valve may be required to comply with maximum temperature and pressure requirements. -
Page 4: Flow Adjustment
FLOW ADJUSTMENT The flow rate can be adjusted without shutting off the water supply or removing the mechanism. 1. Pull out the colour indicator in the centre of push button. 2. Insert a 3mm Allen key into the slot in the centre of push button. -
Page 5: Maintenance
maintenance TIME FLOW CARTRIDGE- CLEANING If the automatic shut-off takes too long or if there is continuous flow: 1. Unscrew cartridge [3] from body [4] and pull off Time Flow Chamber [12]. 2. Clean the inside of the Time Flow Chamber [12] using a clean, dry cloth, and clean the calibrated groove [11] with a non-metallic, sharp point. -
Page 6: Troubleshooting
troubleshooting PROBLEM CAUSE RECTIFICATION Water runs constantly / Debris fouling time flow Dismantle cartridge and clean. leaking from outlet cartridge If problem persists, replace components using service kit or replace cartridge. If debris is an ongoing problem, install a strainer (40 mesh) upstream Scale build up on time Dismantle cartridge and clean... - Page 7 dimensions 5/8" BSP All measurements are in millimetres. www.enware.com.au Page 7 © Enware Pty Ltd...
-
Page 8: Product Warranty Statement
- WATTS AUSTRALIA Effective 27 October 2023 3. Our responsibilities This Warranty Statement applies to products supplied by Australian Valve (a) In the event that the Supplier is reasonably satisfied that there is a Group Pty Ltd (ACN 068 227 270) (AVG) or Enware Pty Ltd (ACN 662...
Need help?
Do you have a question about the ENWARE TFC794R and is the answer not in the manual?
Questions and answers