Related Manuals for Minnich A-1C-96
Summary of Contents for Minnich A-1C-96
-
Page 1: Chapter 1-Introduction
A-1C-96 DOWEL DRILL OPERATOR/SERVICE MANUAL Minnich Manufacturing 1444 ST RT 42 Mansfield,OH 44903 Contact Phone: (419)-903-0010 Email: sales@minnich-mfg.com Revision Date: 04/11/2024... -
Page 2: Table Of Contents
Chapter 2 - Parts Manual..........................20 Hammer Parts............................35 Notes...............................37 Warranty..............................38 Parts Ordering Online..........................39 It is Minnich’s policy to constantly strive to See engine manual for information pertaining improve our products. The information, spec- to the engine. ifications, and illustrations in this publication... -
Page 3: General Warnings
GENERAL WARNINGS CALIFORNIA PROPOSITION 65 Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the Sate of California to cause cancer, birth defects and other reproductive harm. -
Page 4: General Safety
GENERAL SAFETY Do not operate or service the equipment before SAFETY SYMBOLS reading the entire manual. Safety precautions Potential hazards associated with the operation should be followed at all times when operating this of this equipment will be referenced with hazards equipment. - Page 5 ∆ Never use accessories or attachments that are glasses, respirator protection, hearing pro- not recommended by Minnich for the equip- tection, steel-toes boots and other protec- ment. Damage to the equipment and/or injury tive devises required by the job or city and to user may result.
- Page 6 GENERAL SAFETY ENVIRONMENTAL SAFETY/DECOMMISSIONING ∆ DO NOT expose vibrator to rain. ∆ DO NOT use vibrator motor in damp or wet ∆ DO NOT pour waste or oil directly into the locations without proper electrical circuits. ground, down a drain or into any water ∆...
- Page 7 PINCH PIVOT POINTS proper size and pressure rating for the drill unit. WARNING ∆ Make sure the lubricator is filled with proper NOISE MAY DAMAGE HEARING lubricant. See Minnich recommended lubricant WEAR PROPER HEARING PROTECTION below. FLYING PARTICLES MAY CAUSE EYE INJURIES WEAR PROPER EYE STAND OWNERS MANUAL COMPLETELY.
- Page 8 Placement and consolidation To find the latest revision of this publication, visit our website at: www.minnich-mfg.com The force exerted by an internal concrete vibra- tor is controlled by the weight and the speed at which the eccentric rotates. The centrifugal...
- Page 9 GENERAL SAFETY TOOL USE AND CARE SERVICE 1. Only qualified persons should operate the 1. DO NOT run the drill unit while you make machine. Make sure you operate and service your adjustments and repairs unless the procedure is machine according to the instructions listed in this approved.
-
Page 10: General Specifications
GENERAL SPECIFICATION A-1C-96 Single Drill, On Slab Unit Model A-1C-96 Drill Steel Shank .875” x 3.25” (2.22cm x 8.26cm) Drill Steel Length 48” (121.92cm) (Under Collar) Drill Bit Diameter .625” - 1.625” (15.9mm - 41.3mm) Maximum Drill 42” (106.68cm) Depth* Drill Distance 1.5”... - Page 11 GENERAL SPECIFICATION Pneumatic Connection: • An approved air disconnect is required to be installed in accordance to all Local and National Codes. Environmental: • +5°C to +40°C (+41°F to +104°F) • 50% Rh at +40°C (+104°F), (90% Rh at +20°C (+68°F)) •...
-
Page 12: Safety Decal Location
SAFETY DECAL LOCATION All safety labels on Minnich Manufacturing units have been carefully placed so they can be easily seen at all times. There are several different types of labels on the units. Always keep these warnings free of dirt, concrete, or anything else that restricts visibility. - Page 13 SAFETY DECAL LOCATION 12287-42 12287-38 12287-36 12287-36 12287-37 Dowel Drill Manual...
-
Page 14: Pressure Regulator
PRESSURE REGULATOR OPERATION A regulator is used in a compressed air system to maintain nearly constant outlet pressure despite changes in the inlet air pressure and changes in downstream flow requirements. Outlet pressure is controlled by the adjusting screw (1). clockwise rotation increases and counter- clockwise rotation decreases outlet pressure setting. -
Page 15: Standard Setup
STANDARD SETUP UNLOADING THE UNIT POSITION MACHINE FOR DRILLING If you’re A-1C unit is on a truck bed or other • Position the drill unit where the first set of plat-form and needs to be lifted into position, holes is to be drilled, keeping the drill unit back use the from the edge of the slab slightly. -
Page 16: Drilling Operations
DRILLING OPERATIONS 1. Make sure the lubricator is full. See OPERATOR POSITION recommended lubricants on page 3-1. A-1C series units should be filled every two hours. 2. Use a 3/4” (19mm) hose to supply air to the Failure to follow the instructions below may re- drill unit for A-1C series units. -
Page 17: Troubleshooting
Troubleshooting Air Drill PROBLEM: DRILL DOES NOT RUN Cause Remedy DRILL NOT GETTING AIR 1. On Multi Drill units, switch airline with drill that is working properly. If drill now runs check the air control valve. If the valve works, check the drill. - Page 18 Troubleshooting Air Drill PROBLEM: DRILL RUNS SLOW OR DOES NOT DRILL EFFECTIVELY Cause Remedy NOT ENOUGH AIR REACHING On Multi Drill units. Turn off one or two drills. If DRILL. IT SHOULD HAVE 100SCFM the remaining drills pick up speed, check the air (47.2DM^3/ .) PER DRILL AND 110 compressor.
-
Page 19: Recommended Oil
RECOMMENDED Be sure lubricator is full. See recommended oils below. Step 1 Step 2 Make sure slab wheels are square against face of slab. Step 3 Using feed control valve, feed bit against slab. Using drill control valve, turn drill on and drill until the Step 4 drill slider is against the stop clamp, which should be set for the required depth of hole. -
Page 20: Chapter 2 - Parts Manual
PARTS MANUAL Dowel Drill Manual... - Page 21 GENERAL SAFETY Dowel Drill Manual...
- Page 22 PARTS MANUAL Dowel Drill Manual...
- Page 23 GENERAL SAFETY Dowel Drill Manual...
- Page 24 PARTS MANUAL Dowel Drill Manual...
- Page 25 PARTS MANUAL Dowel Drill Manual...
- Page 26 PARTS MANUAL Dowel Drill Manual...
- Page 27 PARTS MANUAL Dowel Drill Manual...
- Page 28 PARTS MANUAL Dowel Drill Manual...
- Page 29 PARTS MANUAL Dowel Drill Manual...
- Page 30 PARTS MANUAL Dowel Drill Manual...
- Page 31 PARTS MANUAL Dowel Drill Manual...
- Page 32 PARTS MANUAL Dowel Drill Manual...
- Page 33 PARTS MANUAL Dowel Drill Manual...
- Page 34 GENERAL SAFETY Dowel Drill Manual...
-
Page 35: Hammer Parts
GENERAL SAFETY 50# (23kg) Rock Drill 0A9350-00000 Dowel Drill Manual... - Page 36 PARTS MANUAL *WHEN ORDERING REPLACEMENT PARTS YOU NEED TO FURNISH THE MODEL AND SERIAL NUMBER OF THE DRILL TOOL* Dowel Drill Manual...
-
Page 37: Notes
NOTES Dowel Drill Manual... -
Page 38: Warranty
The product must have been purchased resulting from the installation or removal of this directly from Minnich or from an authorized product from any installation, any unauthorized Minnich reseller. tampering with this product, any repairs at-... -
Page 39: Parts Ordering Online
Scan for Helpful Videos! WE ACCEPT THE FOLLOWING CARDS! NON-DEALER AND INTERNATIONAL COSTUMERS: Contact Minnich Manufacturing through the following num- ber to locate a dealer near you. (419-903-0010) All orders are treated as Standard Orders and will ship the same day if received prior to...
Need help?
Do you have a question about the A-1C-96 and is the answer not in the manual?
Questions and answers