Handler 52CSU Owner's Manual

9. The Etcher Catcher has a Bussman GMC-1A fuse
that powers the fan and the light. The fuse and a
spare fuse are stored in the AC power cord recep-
tacle near the rear of the chamber. To check or
change the fuse, follow these directions:
Active
AC receptacle Pry open
Fuse Spare
with power cord
fuse drawer
Fuse
removed
Remove the power cord from the AC receptacle to
expose the fuse holder drawer. Use the blade of a
small screwdriver in the slot of the fuse holder and
gently pry outward. The active fuse is in the back of
the drawer and a spare fuse is in the front compart-
ment. If the glass case of the active fuse is darkened,
the fuse is blown. From the underside of the drawer,
push out the blown fuse using a small screwdriver.
Do not use a higher ampere fuse.
Replacement Parts
P52-01P Viewport
P52-02P Led Light Assembly
P52-03P Rubber Entry Sleeve
P52-04P Thumb Screw 10.5mm Long for Viewport
P52-05P Hinge Assembly W/ Washers & Nuts
P52-06P On/Off Switch
P52-07P Thumb Screw 2.5mm Long for
Rubber Sleeve
P52-08P Clear Protective Film
P52-09P Magnifier Assembly 2X/4X
P52-10P Fuse, 1A, Time Delay
P52-11P LED Driver
P52-12P Clean-Out Plug For 52csu
P550-01 Motor Suction 115 V for 52CSU
P550-01-E Motor Suction 230 V for 52CSU-E
52-FP Filter
Handler Manufacturing LLC
612 North Avenue, East
159 GRASSY PLAIN STREET
BETHEL, CT 06801 USA Westfield, NJ 07090 USA
908-233-7796
info@handlermfg.com
LIMITED WARRANTY
Warranty period is 1 year for the Handler Etcher
Catcher.
Handler manufacturing, LLC warrants, to the
original purchaser only, that its products will be
free from defects in material or workmanship
for the applicable period of time indicated above
following the purchase date. During the warran-
ty period, the defective product will be repaired
or replaced without charge or, at our sole
option, the purchase price will be refunded. This
warranty does not cover damage caused in tran-
sit or by accident, misuse or ordinary wear.
ALL IMPLIED WARRANTIES INCLUDING,
WITHOUT LIMITATION, IMPLIED WARRANTIES
OF FITNESS FOR A PARTICULAR PURPOSE
AND MERCHANTABILITY, ARE LIMITED IN
DURATION TO THE APPLICABLE WARRANTY
PERIOD. IN NO EVENT WILL WE BE LIABLE
FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states do not allow limitations
on how long an implied warranty lasts or the
exclusion or limitation of incidental or conse-
quential damages, so the above limitations or
exclusion may not apply to you.
At our sole option, repair, replacement or refund
will be made if the product is returned postage
prepaid to:
Handler Manufacturing LLC
612 North Avenue, East, Westfield, NJ 07090
159 GRASSY PLAIN STREET, BETHEL, CT 06801 USA
All warranty repairs must be done at our factory
at the above address. We will not pay any
shipping or transportation charges.
This warranty gives you specific legal rights,
and you may also have other rights which vary
from state to state.
Please retain your proof of purchase
for warranty repairs.
Repair Services
Authorized repair service is available. You must
call or email Handler to obtain the Return
Merchandise Authorization number before
returning the item. Send items for repair to the
factory marked:
"Attention: RMA No."
Handler Manufacturing LLC
612 North Avenue East
159 GRASSY PLAIN STREET
Westfield, NJ 07090 USA
BETHEL, CT 06801 USA
Enclose the item(s), a packing list, a description of
the problem or repairs needed, daytime phone
number and email address. Estimates of repair cost
will be made upon request.
Rev. 8/2020
Owner's Manual
#52CSU Etcher Catcher
For Your Own Safety
Please read this Manual before operating your Handler
•
Etcher Catcher.
Always wear eye protection while using power tools.
•
http://handlermfg.com