Advertisement
Quick Links
Advertisement
Related Manuals for PRODIS CL Series
Summary of Contents for PRODIS CL Series
- Page 1 CL SERIES ICE MAKER USER MANUAL ICE MAKER CLS250220UM Rev 1.0...
-
Page 2: Installation
TABLE OF CONTENTS PART I WARNINGS PART II INSTALLATION PART III OPERATING INSTRUCTIONS PART IV MAINTENANCE AND CLEANING PART V TROUBLE SHOOTING CLS250220UM Rev 1.0... - Page 3 PART I 01. PROPER INSTALLATION, 13. IT IS THE USERS RESPONSIBILITY TO MAINTENANCE OF THIS MACHINE ARE ALL ENSURE ONGOING MAINTENANCE IMPORTANT FOR MAINTAINING PRODUCTION MAKER COMPLETED AND USER SAFETY. IN ORDER TO REDUCE ACCORDANCE WITH MANUFACTURERS FAILURE RATE PLEASE READ THESE INSTRUCTIONS LAID OUT IN THIS MANUAL.
- Page 4 PART II IMPORTANT iv. REMOVE THE PROTECTIVE PLASTIC FILM FROM THE EXTERIOR BEFORE INSTALLATION. IF 01. THIS MANUAL IS AN INTEGRAL PART THE ICEMAKER HAS BEEN EXPOSED TO SUN OR OF THE ICE MAKER AND SHOULD BE KEPT HEAT ALLOW THE ICE MAKER TO COOL DOWN AND PRESERVED BY THE USER FOR FUTURE BEFORE REMOVING THE PROTECTIVE FILM.
- Page 5 PART II LEVELLING THE ICE MAKER WARNING 01. CARE SHOULD BE TAKEN TO ENSURE THE ELECTRICAL CONNECTIONS MUST ICE MAKER IS PERFECTLY LEVEL FOR CORRECT CONFORM TO LOCAL REGULATIONS AND BE OPERATION. THE UNIT HAS 4 ADJUSTABLE FEET CARRIED OUT BY A QUALIFIED ENGINEER ON THE BOTTOM FOR LEVELLING.
- Page 6 PART II 05. PUSH THE FLEXIBLE DRAIN HOSE ON THE IS THE MACHINE CORRECTLY EARTHED? DRAIN SPIGOT AT THE REAR OF THE MACHINE AND SECURE WITH THE CLIP PROVIDED. THE DRAIN PIPE CAN BE CUT TO LENGTH TO ALLOW IS THE WATER TO THE ICE MAKER TURNED THE DRAIN CONNECTION TO HAVE A SLIGHT FALL IF NECESSARY IS THE POWER TO THE MACHINE SWITCHED...
- Page 7 PART III OPERATING INSTRUCTIONS ICE THICKNESS ADJUSTMENT WARNING AFTER TURNING OFF YOUR ICE MAKER YOU MUST WAIT AT LEAST 3 MINUTES BEFORE RESTARTING TO AVOID DAMAGE TO THE COMPRESSOR YOUR ICE MAKER FEATURES A SIMPLE CONTROL PANEL WITH THREE INDICATOR LIGHTS AND TWO AFTER THE INITIAL HARVEST CHECK THE SIZE OF BUTTONS.
- Page 8 PART III MAINTENANCE AND CLEANING OPERATING PRINCIPLE THE ICE MAKER WILL ENTER A 3 MINUTE CLEANING PERIODIC CLEANING AND PROPER MAINTENANCE CYCLE WHEN FIRST TURNED ON. WILL EXTEND THE LIFE OF YOUR ICE MAKER, ENSURE MAXIMUM EFFICIENCY AND DELIVER AFTER THE CLEANING CYCLE IS COMPLETE THE ICE BETTER TASTING ICE TO YOUR CUSTOMER.
- Page 9 PART IV EXTERIOR CLEANING TO CLEAN YOUR AIR FILTER SLIDE THE FILTER OUT FROM THE FRONT GRILL AND REMOVE ANY DUST ALWAYS CLEAN THE EXTERIOR STAINLESS STEEL OR DIRT USING A SOFT BRUSH AND A VACUUM PARTS OF THE ICE MAKER WITH A MICRO-FIBRE CLEANER.
-
Page 10: Specification
PART IV TURN OFF THE MAINS WATER SUPPLY AND WATER DISTRIBUTOR CLEANING DISCONNECT THE WATER INLET HOSE. IF YOUR ICE CUBES ARE NOT FORMING CORRECTLY REMOVE ALL REMAINING ICE FROM THE STORAGE OR THE OUTPUT OF ICE CUBES DROPS THE WATER BIN. -
Page 11: Troubleshooting
PART V TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE SUGGESTED SOLUTION • CHECK POWER IS ON AT THE SOCKET ICE MAKER NOT CONNECTED • CHECK CABLE IS CORRECTLY PLUGGED IN TO MAINS ELECTRICITY • CHECK FOR DAMAGE ON POWER CABLE, USE A QUALIFIED ENGINEER TO CORRECTLY REPLACE IF NECESSARY MACHINE IS TURNED OFF... - Page 12 Project Distribution Ltd Unit 1 Sun Street Stoke on Trent United Kingdom ST1 4JW Tel: 01782 280289 www.prodis.co.uk sales@prodis.co.uk CLS250220UM Rev 1.0...
Need help?
Do you have a question about the CL Series and is the answer not in the manual?
Questions and answers