Matco Tools MSC4FDFISH24 Manual

It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility of the device
owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or not legible, contact
Matco Tools for replacements. If the operator is not fluent in English, the product and safety instructions shall be read and discussed with the opera-
tor in the operator's native language by the purchaser/owner or his designee, making sure that the operator
comprehends its contents. PLEASE NOTE: Loading cart beyond rated capacity may cause structural damage to the cart as well as personal and /or
property damage. Please educate your customers to the dangers of overloading.
MSC4FD: Overall, Total Load Capacity: ............ 600 lbs.
MSC4: Overall, Total Load Capacity: .................. 500 lbs.
Lid: When Closed, Total Load Capacity: ............ 150 lbs. (evenly dispersed on top)
Lid: When Open, Total Load Capacity: .............. 5 lbs. (evenly dispersed on inside/outside)
Top Compartment Total Load Capacity: ............ 180 lbs. (evenly dispersed)
3" Split Drawers, Each: ...................................... 30 lbs. (evenly dispersed)
3" Non-Split Drawer:........................................... 70 lbs. (evenly dispersed)
4" Drawer: ........................................................... 70 lbs. (evenly dispersed)
5" Drawer: ........................................................... 70 lbs. (evenly dispersed)
Bottom Shelf ....................................................... 150 lbs. (evenly dispersed on bottom)
PLEASE NOTE: Loading cart beyond rated capacity may cause structural damage to the cart as well as personal and/or property
damage. Please educate your customers to the "dangers of overloading". Do
• Lock lid and drawers before moving. • Apply brake on locking casters anytime cart is in place. • Do not pull cart. Push from handle on end
to move. • Units can tip or fall causing damage or personal injury. • Cart is designed to roll easily on flat surfaces and should not be used on
uneven or inclined surfaces. • Do not open more than one loaded drawer at a time. • Do not stand on or step in drawers. • Keep children away
from unit. • Wear gloves when lifting edges. • Before connecting to a power supply, always check to make sure the power supply corresponds
to the voltage required on the product. • Fully insert plug to reduce the risk of electric shock. • Always unplug when not in use. • Disconnect
power before installing or servicing. • Do not try to plug in unit or product when hands are wet or damp, or if standing on a wet or damp
surface or in water. • Never attempt to pick up unit or plugged in product that should fall in standing water. • This unit is not waterproof
and is intended for general use indoors. • Do not use in potentially dangerous locations, such as flammable or explosive atmospheres.
• Keep cord away from heat, oil, sharp edges or moving parts. • Failure to heed these warnings may result in personal injury and/or property
damage.
WARNING: This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information go to www.P65Warnings.ca.gov.
TROUBLESHOOTING
Problem: Drawers appear not to fit, do not slide in accurately and
bump the cart sides.
Solution: The roller bearing slides must be fully engaged into the
mounting slots on all drawers. They potentially could fall out of posi-
tion during shipment. Check the side of the cart to determine which
slide is out of position.
Remove the drawer that is out of position. The drawer is removed by
the two clips on the actual roller bearing slide.
Simply push the roller bearing slide back down into position.
Insert the drawer back onto the roller bearing slides.
MSC4FDFISH24
FULL DRAWER SERVICE CART THEME - FISH 2024
WARNING
• Read and follow all instructions in User's Manual.
• Do not load carts beyond rated capacity
not attempt to push cart with items on the top lid.
Problem: Back Lock/Unlock Switch does not engage
the drawer.
Solution: The inside Lock/Unlock slide potentially could fall
out of its groove during shipment. Unscrew the four screws that are
holding the Lock/Unlock slide in place.
Once the screws are removed, simply place the latch back onto the
slide and tighten the four screws back down.
1
MSC4FDFISH24
Copyright © 2023
All rights reserved.
REV. 102323