Advertisement
Quick Links
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com
|
Phone: 818-991-1778
WARRANTY INFORMATION:
ALL SWITCH Works Electronics are covered by a limited 1 year warranty against defects
in material or workmanship. Contact SSV Works for further warranty information.
FEATURES & BENEFITS:
Left/Right Turn Signal with Automatic Canceling Feature
Dedicated Horn Output
License Plate Light Output
Emergency Hazard Light Switch
Direct plug in to the factory tail light connectors
RGB Backlight Buttons
Weather-Proof for Offroad Use
Built-In Circuit Protection Detects Any Short Circuits, Over Current, Under Current and Low Voltage
Programmable RGB Backlight Colors to Match the Dash Lights
|
Fax: 866-293-6751
230-SWTS-KRX
2020-2024 Kawasaki Teryx KRX1000
Turn Signal Kit with Horn
Please read and understand these
!
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
BY
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for SSV Works SWITCH WORKS TANGO 2 230-SWTS-KRX
Summary of Contents for SSV Works SWITCH WORKS TANGO 2 230-SWTS-KRX
- Page 1 230-SWTS-KRX 2020-2024 Kawasaki Teryx KRX1000 Turn Signal Kit with Horn SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com Phone: 818-991-1778 Fax: 866-293-6751 WARRANTY INFORMATION: Please read and understand these ALL SWITCH Works Electronics are covered by a limited 1 year warranty against defects instructions completely before in material or workmanship.
- Page 2 SWTS-KRX SWITCH Works Tango2 Parts List Tango2 Turn Signal Module Tango2 Turn Signal Rocker Tango2 Turn Signal Main Switch Harness [B-H3271] Front Turn Signal Extension Kawasaki KRX Rear Turn Signal KRX Tail light/Turn Signal Harness (x2) [B-S2959] Harness [B-H3112] Adapter Kit [B-H3122] Zip Ties (x10) Horn Assembly, 500hz Tango2 Front Turn Signal LED...
- Page 3 SWTS-KRX SWITCH Works TANGO2 Kawasaki Turn Signal Kit Wiring Diagram Description Part # Tango2 Turn Signal Module Tango2 Turn Signal Rocker Switch Tango2 Turn Signal Main Harness B-H2939 Power Connector to Busbar Pulse Connector Power Input Harness, 3 ft. B-H3413 Front Turn Signal Extension Harness (x2) B-H2959 LED Lamp (Front Right)
-
Page 4: Tools Needed For Installation
SWTS-KRX TOOLS NEEDED FOR INSTALLATION - Phillips Screw Driver - Drill - 3/4” Hole Saw A. Locate a suitable mounting location for the TANGO2 Turn Signal module. Secure the module to a panel using screws or zip tie it to a harness. B. - Page 5 SWTS-KRX D. Route the front left and right turn signal extension cables to the E. Run the TANGO2 rear turn signal harness (B-H3205) to the rear of front of the vehicle. Make sure to route the correct cable connector the vehicle. Use zip ties to secure the cable away from any moving end that will plug to the LED lamp.
- Page 6 SWTS-KRX J. Horn mounting recommendations: 1. Mount away from moving parts; K. Run the KRX Rear Turn Signal Harness (B-H3112) to the rear of the 2. Mount as high as possible; 3. Mount with the horn facing downward vehicle. Begin installation on the passenger side tail light. Unplug to protect from water damage.
- Page 7 SWTS-KRX N. Plug in the KRX TS Adapter (B-H3122) to the B-H3112 “DRIVER O. Crimp the ring terminals to the Power Input Harness (B-H3413). OUTPUT” connector and plug the other end to the tail light. Use zip ties to secure the harnesses. P.
- Page 8 4 seconds until the rocker switch backlight turns bright. Use the left and right buttons to select the color. Press the horn button to save the color. © 2024 SSV Works, Oxnard, CA 93030 SWTS-KRX Rev. A 2-9-24...
Need help?
Do you have a question about the SWITCH WORKS TANGO 2 230-SWTS-KRX and is the answer not in the manual?
Questions and answers