Advertisement
Quick Links
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com
|
Phone: 818-991-1778
WARRANTY INFORMATION:
All SWITCH Works Electronics are covered by a limited 1 year warranty against defects
in material or workmanship. Contact SSV Works for further warranty information.
FEATURES & BENEFITS:
Left/Right Turn Signal with Automatic Canceling Feature
Dedicated Horn Output
License Plate Light Output
Emergency Hazard Light Switch
Direct plug in to the factory tail light connectors
RGB Backlight Buttons
Weather-Proof for Offroad Use
Built-In Circuit Protection Detects Any Short Circuits, Over Current, Under Current and Low Voltage
Programmable RGB Backlight Colors to Match the Dash Lights
|
Fax: 866-293-6751
230-SWTS-RG3
2013-2018 Polaris Ranger
Turn Signal Kit with Horn
Please read and understand these
!
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
BY
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for SSV Works SWITCH WORKS TANGO 2 230-SWTS-RG3
Summary of Contents for SSV Works SWITCH WORKS TANGO 2 230-SWTS-RG3
- Page 1 230-SWTS-RG3 2013-2018 Polaris Ranger Turn Signal Kit with Horn SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com Phone: 818-991-1778 Fax: 866-293-6751 WARRANTY INFORMATION: Please read and understand these All SWITCH Works Electronics are covered by a limited 1 year warranty against defects instructions completely before in material or workmanship.
- Page 2 SWTS-RG3 SWITCH Works Tango2 Parts List Tango2 Turn Signal Module Tango2 Turn Signal Rocker Tango2 Turn Signal Main Switch Harness [B-H3271] Front Turn Signal Extension Polaris Ranger Rear Turn Signal Tango2 Front Turn Signal LED Harness (x2) [B-S2959] Harness [B-H3205] Lamps (x2) [B-H2813] Zip Ties (x10) Power Input Harness...
- Page 3 SWTS-RG3 SWITCH Works TANGO2 Polaris Ranger Turn Signal Kit Wiring Diagram Description Part # Tango2 Turn Signal Module Tango2 Turn Signal Rocker Switch Tango2 Turn Signal Main Harness B-H3271 Power Connector to Busbar Pulse Connector Power Input Harness, 3 ft. B-H3413 Front Turn Signal Extension Harness (x2) B-H2959...
-
Page 4: Tools Needed For Installation
SWTS-RG3 TOOLS NEEDED FOR INSTALLATION - Phillips Screw Driver - Drill - 3/4” Hole Saw A. Using a panel tool, remove the (4) push pins retaining the dash cover. B. Lift and gently pull the dash cover away from the vehicle to expose the dash cavity. - Page 5 SWTS-RG3 E. Route the front left and right turn signal extension cables to the F. Run the TANGO2 rear turn signal harness (B-H3205) to the rear of front of the vehicle. Make sure to route the correct cable connector the vehicle. Use zip ties to secure the cable away from any moving end that will plug to the LED lamp.
- Page 6 SWTS-RG3 K. Horn mounting recommendations: 1. Mount away from moving parts; L. Unplug the factory tail light connector and plug it to the “PASS. 2. Mount as high as possible; 3. Mount with the horn facing downward INPUT” connector of the Polari Ranger Rear Turn Signal Harness to protect from water damage.
- Page 7 SWTS-RG3 BATT BATT Q. Plug the 3-pin connector of the Power Input Harnes (B-H3413) to R. Run the BATT, ACC and GND wires of the Power Input Harness the Polaris Ranger Turn Signal Main harness (B-H3271). (B-H3413) to the factory busbar and screw in the ring terminals to the busbar.
- Page 8 With ACC off, press and hold either the left or right button for 4 seconds until the rocker switch backlight turns bright. Use the left and right buttons to select the color. Press the horn button to save the color. © 2024 SSV Works, Oxnard, CA 93030 SWTS-RG3 Rev.A 2-7-24...
Need help?
Do you have a question about the SWITCH WORKS TANGO 2 230-SWTS-RG3 and is the answer not in the manual?
Questions and answers